Thermal Behavior and Morphology of Thermoplastic Polyurethane Derived from Different Chain Extenders of 1,3- and 1,4-Butanediol

Preparation and Properties of a Novel Cross-Linked Network Waterborne Polyurethane for Wood Lacquer

Waterborne polyurethane (WPU) is a waterborne coating with excellent physicochemical properties. Its deficiencies of water resistance, chemical resistance, staining, and hardness have limited the wide application of polyurethane in the wood lacquer market. In this study, polycarbonate diols (PCDL) were used as soft segments and WPCU was modified by cross-linking using Trimethylolpropane (TMP) to prepare polycarbonate type WPU (WPCU) with cross-linked network structure. The new wood lacquer was prepared by adding various additives and tested by applying it on wood board. The successful synthesis of WPCU was determined by FTIR testing, and the cross-linking degree of WPCU was probed by low-field NMR. The viscosity of the cross-linked WPCU emulsion showed a decreasing trend compared to the uncross-linked WPCU emulsion, and WPCU-2 had the smallest particle size. Compared with the uncrosslinked WPCU film, the crosslinked WPCU film had lower water absorption (2.2%), higher water contact angle (72.7°), excellent tensile strength (44.02 MPa), higher thermomechanical, and better water and alcohol resistance. The effect of crosslinker content on the microphase separation of WPCU chain segments on the surface roughness of the film was investigated by SEM. The wood paint prepared by WPCU emulsion has good dry heat resistance, chemical resistance, and adhesion, and the hardness of the wood paint when the TMP content is 3% reaches H. It also has good resistance to sticky stains, which can be used to develop new wood lacquer.

4D Printing of Electroactive Triple-Shape Composites

Triple-shape polymers can memorize two independent shapes during a controlled recovery process. This work reports the 4D printing of electro-active triple-shape composites based on thermoplastic blends. Composite blends comprising polyester urethane (PEU), polylactic acid (PLA), and multiwall carbon nanotubes (MWCNTs) as conductive fillers were prepared by conventional melt processing methods. Morphological analysis of the composites revealed a phase separated morphology with aggregates of MWCNTs uniformly dispersed in the blend. Thermal analysis showed two different transition temperatures based on the melting point of the crystallizable switching domain of the PEU (T_m~50 ± 1 °C) and the glass transition temperature of amorphous PLA (T_g~61 ± 1 °C). The composites were suitable for 3D printing by fused filament fabrication (FFF). 3D models based on single or multiple materials were printed to demonstrate and quantify the triple-shape effect. The resulting parts were subjected to resistive heating by passing electric current at different voltages. The printed demonstrators were programmed by a thermo-mechanical programming procedure and the triple-shape effect was realized by increasing the voltage in a stepwise fashion. The 3D printing of such electroactive composites paves the way for more complex shapes with defined geometries and novel methods for triggering shape memory, with potential applications in space, robotics, and actuation technologies.

Effect of Aromatic Chain Extenders on Polyurea and Polyurethane Coatings Designed for Defense Applications

The present work describes the synthesis of new versatile polyurea (PU) and polyurethane (PUR) matrices, including different chain extenders, which facilitate the design of distinct, tunable properties, and high-performance derivatives. These polymers can be used for various defense and security applications, such as coatings for ballistic protection, CBRN protection, binders for energetic formulations, etc. Combining aliphatic and aromatic molecules in PU or PUR structures enables the synthesis of polymers with improved and controllable thermo-mechanical properties. Thus, for polyurea synthesis, we utilized two types of polymeric aliphatic diamines and three types of aromatic chain extenders (1,1'-biphenyl-4,4'-diamine, benzene-1,2-diamine, and 1,2-diphenylhydrazine). An analogous method was used to synthesize polyurethane films by employing one polymeric aliphatic polyol and three types of aromatic chain extenders (benzene-1,3-diol, benzene-1,4-diol, and benzene-1,2,3-triol). Subsequently, various analytic techniques (Fourier transform infrared spectroscopy-attenuated total reflectance (FTIR-ATR), single cantilever dynamic mechanical analysis (DMA), thermogravimetric analysis (TGA), frequency-dependent shear modulus survey, tensile tests, water contact angle measurements, and scanning electron microscopy (SEM) with energy-dispersive X-ray analysis (EDX)) have been utilized to characterize the synthesized materials and to evaluate the influence of each chain extender on their final properties.

Analysis of Thermoplastic Copolymers by Mild Thermal Degradation Coupled to Ion Mobility Mass Spectrometry

Thermal desorption/degradation with an atmospheric solids analysis probe (ASAP) and ion mobility (IM) separation are coupled with mass spectrometry (MS) analysis and tandem mass spectrometry (MS/MS) fragmentation to characterize thermoplastic elastomers. The compounds investigated, which are used in the manufacture of a wide variety of packaging materials, are mainly composed of thermoplastic copolymers, but also contain additional chemicals ("additives"), like antioxidants and UV stabilizers, for enhancement of their properties or protection from degradation. The traditional method for analyzing such complex mixtures is vacuum pyrolysis followed by electron or chemical ionization mass spectrometry, often after gas chromatography separation. Here, an alternative, faster approach, involving mild degradation at atmospheric pressure (ASAP) and subsequent characterization of the desorbates and pyrolyzates by IM-MS, and if needed, MS/MS is presented. Such multidimensional dispersion considerably simplifies the resulting spectra, permitting the conclusive separation, characterization, and classification of the multicomponent materials examined.

Investigating Physio-Thermo-Mechanical Properties of Polyurethane and Thermoplastics Nanocomposite in Various Applications

The effect of the soft and hard polyurethane (PU) segments caused by the hydrogen link in phase-separation kinetics was studied to investigate the morphological annealing of PU and thermoplastic polyurethane (TPU). The significance of the segmented PUs is to achieve enough stability for further applications in biomedical and environmental fields. In addition, other research focuses on widening the plastic features and adjusting the PU-polyimide ratio to create elastomer of the poly(urethane-imide). Regarding TPU- and PU-nanocomposite, numerous studies investigated the incorporation of inorganic nanofillers such as carbon or clay to incorporating TPU-nanocomposite in several applications. Additionally, the complete exfoliation was observed up to 5% and 3% of TPU-clay modified with 12 amino lauric acid and benzidine, respectively. PU-nanocomposite of 5 wt.% Cloisite®30B showed an increase in modulus and tensile strength by 110% and 160%, respectively. However, the nanocomposite PU-0.5 wt.% Carbone Nanotubes (CNTs) show an increase in the tensile modulus by 30% to 90% for blown and flat films, respectively. Coating PU influences stress-strain behavior because of the interaction between the soft segment and physical crosslinkers. The thermophysical properties of the TPU matrix have shown two glass transition temperatures (Tg's) corresponding to the soft and the hard segment. Adding a small amount of tethered clay shifts Tg for both segments by 44 °C and 13 °C, respectively, while adding clay from 1 to 5 wt.% results in increasing the thermal stability of TPU composite from 12 to 34 °C, respectively. The differential scanning calorimetry (DSC) was used to investigate the phase structure of PU dispersion, showing an increase in thermal stability, solubility, and flexibility. Regarding the electrical properties, the maximum piezoresistivity (10 S/m) of 7.4 wt.% MWCNT was enhanced by 92.92%. The chemical structure of the PU-CNT composite has shown a degree of agglomeration under disruption of the sp2 carbon structure. However, with extended graphene loading to 5.7 wt.%, piezoresistivity could hit 10-1 S/m, less than 100 times that of PU. In addition to electrical properties, the acoustic behavior of MWCNT (0.35 wt.%)/SiO2 (0.2 wt.%)/PU has shown sound absorption of 80 dB compared to the PU foam sample. Other nanofillers, such as SiO2, TiO2, ZnO, Al2O3, were studied showing an improvement in the thermal stability of the polymer and enhancing scratch and abrasion resistance.