Heterogeneity of Ex Vivo and In Vivo Properties along the Length of the Abdominal Aortic Aneurysm

Morphology of Abdominal Aortic Aneurysms and Correlation with Biomechanical Tests of Aneurysmal Wall Fragments

BACKGROUND

Evaluate how specific morphologic aspects of abdominal aortic aneurysms (AAAs), including asymmetries, curvatures, tortuosities, and angulations, among others can influence the intrinsic biomechanical properties of the AAA's wall. This study analyzed the correlation of geometric measurements (1-dimensional, 2-dimensional, and 3-dimensional) of preoperative tomographic images of AAA with uniaxial biomechanical tests of the arterial wall fragments of these AAA obtained in open surgical repair of aneurysms.

METHODS

It was a multicenter, experimental, and observational study, and initially 54 individuals were selected who underwent open surgical of AAA, with valid biomechanical tests of the anterior wall of the AAA. Seven individuals were excluded because they had poor preoperative quality computed tomography scans and/or artifacts that impeded image segmentation and extraction of AAA geometric indices. The aortic fragments were subjected to uniaxial biomechanical destructive tests to obtain the following data: maximum load, failure stress, failure tension, failure strain energy, strain, and fragment thickness. In the same patients, preoperative computed tomography scans were performed with the extraction of 26 geometric indices, subdivided into 9 1-dimensional indices, 6 2-dimensional indices, and 11 3-dimensional indices. Data were subjected to statistical analysis using SPSS version 28.

RESULTS

Comparing ruptured and unruptured AAA, no statistical difference was observed between the biomechanical and geometric parameters. The fragment thickness of the ruptured AAA was lower than that of the unruptured AAA (P < 0.05). By comparing tomographic geometric indices and biomechanical parameters of the aortic fragments using Pearson's coefficient, positive and linear correlations (P < 0.05) were observed between the geometric variable maximum diameter (Dmax) of the AAA with maximum load (r = 0.408), failure tension (r = 0.372), and failure stress (r = 0.360). Positive and linear correlations were also observed between the variable diameter/height ratio (DHr) and the maximum load (r = 0.360), failure tension (r = 0.354), and failure stress (r = 0.289). The geometric variable DHr was dependent and correlated with Dmax. Simple regression analysis showed that R2 varied between 8.3% and 16.7%, and all models were significant (P < 0.05).

CONCLUSIONS

Dmax and DHr were linearly and positively correlated with the resistance parameters (maximum load, failure tension, and failure stress) of the AAA fragments. The DHr variable is dependent and correlated with Dmax. There was no correlation between the other geometric indices and the biomechanical parameters of the AAA wall. The asymmetries did not globally influence the biomechanics of AAA wall; however, they may influence regionally. Larger AAAs were stronger than smaller ones. Therefore, such findings may point toward Dmax is still the main geometric parameter, which influences the anterior wall, and possibly globally in the AAA.

Lengthwise regional mechanics of the human aneurysmal ascending thoracic aorta

The prognosis of patients undergoing emergency endovascular repair of ascending thoracic aortic aneurysm (ATAA) depends on defect location, with root disease bearing worse outcomes than proximal or distal aortopathy. We speculate that a spatial gradient in aneurysmal tissue mechanics through the length of the ascending thoracic aorta may fuel noted survival discrepancies. To this end, we performed planar biaxial testing on 153 root, proximal, and distal segments of ATAA samples collected from 80 patients receiving elective open surgical repair. Following data averaging via surface fitting-based interpolation of strain-controlled protocols, we combined in-vitro and in-vivo measurements of loads and geometry to resolve inflation-extension kinematics and evaluate mechanical metrics of stress, stiffness, and energy at consistent deformation levels. Representative (averaged) experimental data and simulated in-vivo conditions revealed significantly larger biaxial stiffness at the root compared to either proximal or distal tissues, which persisted as the entire aorta stiffened during aging. Advancing age further reduced biaxial stretch and energy storage, a measure of aortic function, across all ATAA segments. Importantly, age emerged as a stronger predictor of tissue mechanics in ATAA disease than either bicuspid aortic valve or connective tissue disorders. Besides strengthening the general understanding of aneurysmal disease, our findings provide specifications to customize the design of stent-grafts for the treatment of ATAA disease. Optimization of deployment and interaction of novel endovascular devices with the local native environment is expected to carry significant potential for improving clinical outcomes. STATEMENT OF SIGNIFICANCE: Elucidating the lengthwise regional mechanics of ascending thoracic aortic aneurysms (ATAAs) is critical for the design of endovascular devices tailored to the ascending aorta. Stent-grafts provide a less invasive alternative to support the long-term survival of ATAA patients ineligible for open surgical repair. In this study, we developed a numerical framework that combines semi-inverse constitutive and forward modeling with in-vitro and in-vivo data to extract mechanical descriptors of ATAA tissue behavior at physiologically meaningful deformation. Moving distally from the aortic root to the first ascending aortic branch, we observed a progressive decline in biaxial stiffness. Furthermore, we showed that aging leads to reduced aortic function and is a stronger predictor of mechanics than either valve morphology or underlying syndromic disorder.

Tissue Mechanics and Tissue Engineering

Tissue engineering (TE) combines scaffolds, cells, and chemical and physical cues to replace biological tissues [...]