Revisiting Total Particle Number Measurements for Vehicle Exhaust Regulations

Real-time detection of vehicle-originated condensable particulate matter through thermodenuder integrated aerosol measurement method at tailpipes

Condensable particulate matter (CPM) corresponds to primary particulate matter ≤2.5 μm (PM_2.5) obtained through the condensation of gaseous air pollutants caused by temperature drops in the atmosphere. The internal combustion of vehicle engines can produce CPM because of the condensable compounds in the exhaust gas. Conventional CPM measurement methods have been developed for coal-fired power plants with stable emissions through sampling and off-site analyses. They are therefore unsuitable for detecting the rapidly changing vehicle-originated CPM. In addition, the current system for evaluating PM_2.5 from vehicles, based on the particle measurement program (PMP) protocol, provides only the emission factors of total PM_2.5 (and not CPM separately) at a fixed temperature (∼25 °C) and dilution ratio (∼ × 35). This study reports, for the first time, the development of a real-time detection method for vehicle-originated CPM through a thermodenuder (TD) integrated with real-time aerosol instruments. This method was designed to reduce the loss of CPM due to condensation and diffusion while sampling the exhaust gas. It permits the investigation of the effects of dilution gas temperature (5-45 °C) and dilution ratio (up to × 30) on the formation of CPM. During the feasibility test of this method using a diesel vehicle (Euro-4), the real-time total particle number concentrations (PNs) matched well with those obtained by a PMP protocol-based evaluation system. Moreover, this method detected PNs concentrations ten times higher than the detection limit (4 × 10⁶ particles/cm³) of the PMP-based system. The emission factors of the total PM_2.5 with a bulk density (1 g/cm³) measured by this method also showed consistency with the results of the PMP protocol. The mass emission factor of CPM determined by deploying the TD was ∼14.57 mg/km (∼63% contribution to the total PM_2.5).

Impact of Active Diesel Particulate Filter Regeneration on Carbon Dioxide, Nitrogen Oxides and Particle Number Emissions from Euro 5 and 6 Vehicles under Laboratory Testing and Real-World Driving

Particulate mass concentration is a crucial parameter for characterising air quality. The diesel particulate filter (DPF) is the primary technology used to limit vehicle particle emissions, but it needs periodic cleaning, a process called regeneration. This study aims to assess the impact of active DPF regeneration on the performance and emissions of Euro 5 and 6 vehicles. The study examined both carbon dioxide (CO2) and pollutant (nitrogen oxides (NOx) and particle number (PN)) emissions for eight vehicles tested in the laboratory and on the road. Apart from the DPF, a wide range of emission control systems was covered in this experimental campaign, including exhaust gas recirculation (EGR), diesel oxidation catalyst (DOC), lean NOx trap (LNT) and selective catalytic reduction (SCR) catalyst, revealing the different impacts on NOx emissions. The regeneration frequency and duration were also determined and used to calculate the Ki factor, which accounts for the emissions with and without regeneration, weighted over the distance driven between two consecutive regeneration events. Based on these outcomes, representative emission factors (EF) were proposed for the regeneration phase only and the complete regeneration interval. In addition, the effect of regeneration on efficiency was estimated and compared with other energy consumers. The results indicated a significant impact of DPF regeneration on CO2, NOx and PN emissions, higher in the case of driving cycle testing in the laboratory. The relevant mechanisms behind the elevated emission levels were analysed, focusing on the regeneration period and the test phase following immediately after. The calculation of the Ki factor and the comparison with the official values revealed some weaknesses in its application in real-world conditions; to overcome these, new NOx EF values were calculated, depending on the emission control system. It was revealed that Euro 6 vehicles equipped with SCR could comply with the applicable limits when considering the complete regeneration interval. Finally, it was indicated that the DPF regeneration impact on vehicle efficiency is similar to that of driving with the air conditioning (A/C) system and headlights on.

Evaluation of Measurement Procedures for Solid Particle Number (SPN) Measurements during the Periodic Technical Inspection (PTI) of Vehicles

Periodic technical inspection (PTI) of vehicles guarantees safety and environmental compliance during their lifetime. Particulate matter emissions of diesel vehicles are controlled with opacity measurements. After the introduction of diesel particulate filters (DPFs), particulate matter emissions have drastically decreased and the sensitivity of the opacity method is questioned. Several countries have already or are planning to introduce a solid particle number (SPN) method at their PTI that will either substitute or complement opacity measurements. However, there are differences in the measurement procedures and the limit values. In this study, we compared the different approaches and investigated topics which are still not well defined, such as the uncertainty of the SPN-PTI instruments, repeatability of the procedures, impact of the DPF fill state, and the correlation between type-approval SPN emissions and SPN concentrations during PTI tests. Finally, we compared the SPN-PTI instruments with the opacity meters. Our results showed that SPN-PTI measurements can detect tampered and defective DPFs. We also made suggestions on the measurement procedures and the concentration limit.

Emissions of Carbonaceous Particulate Matter and Ultrafine Particles from Vehicles—A Scientific Review in a Cross-Cutting Context of Air Pollution and Climate Change

Airborne particulate matter (PM) is a pollutant of concern not only because of its adverse effects on human health but also on visibility and the radiative budget of the atmosphere. PM can be considered as a sum of solid/liquid species covering a wide range of particle sizes with diverse chemical composition. Organic aerosols may be emitted (primary organic aerosols, POA), or formed in the atmosphere following reaction of volatile organic compounds (secondary organic aerosols, SOA), but some of these compounds may partition between the gas and aerosol phases depending upon ambient conditions. This review focuses on carbonaceous PM and gaseous precursors emitted by road traffic, including ultrafine particles (UFP) and polycyclic aromatic hydrocarbons (PAHs) that are clearly linked to the evolution and formation of carbonaceous species. Clearly, the solid fraction of PM has been reduced during the last two decades, with the implementation of after-treatment systems abating approximately 99% of primary solid particle mass concentrations. However, the role of brown carbon and its radiative effect on climate and the generation of ultrafine particles by nucleation of organic vapour during the dilution of the exhaust remain unclear phenomena and will need further investigation. The increasing role of gasoline vehicles on carbonaceous particle emissions and formation is also highlighted, particularly through the chemical and thermodynamic evolution of organic gases and their propensity to produce particles. The remaining carbon-containing particles from brakes, tyres and road wear will still be a problem even in a future of full electrification of the vehicle fleet. Some key conclusions and recommendations are also proposed to support the decision makers in view of the next regulations on vehicle emissions worldwide.

Detailed Characterization of Solid and Volatile Particle Emissions of Two Euro 6 Diesel Vehicles

The solid particle number emissions of Diesel vehicles are very low due to the particulate filters as exhaust aftertreatment devices. However, periodically, the trapped particles are oxidized (i.e., active regeneration) in order to keep the backpressure at low levels. The solid particle number emissions during regenerations are only partly covered by the regulations. Many studies have examined the emissions during regenerations, but their contribution to the overall emissions has not been addressed adequately. Furthermore, the number concentration of volatile particles, which is not included in the regulations, can be many of orders of magnitude higher. In this study, the particulate emissions of two light-duty Euro 6 vehicles were measured simultaneously at the tailpipe and the dilution tunnel. The results showed that the weighted (i.e., considering the emissions during regeneration) solid particle number emissions remained well below the applicable limit of 6 × 1011 #/km (solid particles > 23 nm). This was true even when considering solid sub-23 nm particles. However, the weighted volatile particle number emissions were many orders of magnitude higher, reaching up to 3 × 1013 #/km. The results also confirmed the equivalency of the solid particle number results between tailpipe and dilution tunnel locations. This was not the case for the volatile particles which were strongly affected by desorption phenomena. The high number of volatiles during regenerations even interfered with the 10 nm solid particle number measurements at the dilution tunnel, even though a catalytic stripper equipped instrument was also used in the dilution tunnel.