New Generation of Hybrid Materials Based on Gelatin and Bioactive Glass Particles for Bone Tissue Regeneration

Chemical interactions in composites of gellan gum and bioactive glass: self-crosslinking and in vitro dissolution

We investigated the interactions between the organic-inorganic phases in composites and the impact on in vitro dissolution. The composite consists of a hydrogel-forming polysaccharide gellan gum (GG, organic phase) and a borosilicate bioactive glass (BAG, inorganic phase). The BAG loading in the gellan gum matrix varied from 10 to 50 wt%. While mixing GG and BAG, the ions released from BAG microparticles crosslinked with the carboxylate anions of GG. The nature of the crosslinking was assessed, and its impact on mechanical properties, swelling ratio, and enzymatic degradation profile upon immersion for up to 2 weeks was studied. Loading up to 30 wt% of BAG in GG caused an increase in mechanical properties associated with an increasing crosslinking density. At higher BAG loading, excess divalent ions and percolation of particles led to a decrease in the fracture strength and compressive modulus. Upon immersion, a decrease in the composite mechanical properties was attributed to the dissolution of the BAG and the loosening of the glass/matrix interface. The enzymatic degradation of the composites was inhibited at higher BAG loadings (40 and 50 wt%) even when the specimen was immersed for 48 h in PBS buffer with lysozyme. During in vitro dissolution in both SBF and PBS, the ions released from the glass led to the precipitation of hydroxyapatite already at day 7. In conclusion, we thoroughly discussed the in vitro stability of the GG/BAG composite and established the maximum BAG loading to enhance the GG crosslinking and mechanical properties. Based on this study, 30, 40, and 50 wt% of BAG in GG will be further investigated in an in vitro cell culture study.

Robocasting and Laser Micromachining of Sol-Gel Derived 3D Silica/Gelatin/β-TCP Scaffolds for Bone Tissue Regeneration

The design and synthesis of sol-gel silica-based hybrid materials and composites offer significant benefits to obtain innovative biomaterials with controlled porosity at the nanostructure level for applications in bone tissue engineering. In this work, the combination of robocasting with sol-gel ink of suitable viscosity prepared by mixing tetraethoxysilane (TEOS), gelatin and β-tricalcium phosphate (β-TCP) allowed for the manufacture of 3D scaffolds consisting of a 3D square mesh of interpenetrating rods, with macropore size of 354.0 ± 17.0 μm, without the use of chemical additives at room temperature. The silica/gelatin/β-TCP system underwent irreversible gelation, and the resulting gels were also used to fabricate different 3D structures by means of an alternative scaffolding method, involving high-resolution laser micromachining by laser ablation. By this way, 3D scaffolds made of 2 mm thick rectangular prisms presenting a parallel macropore system drilled through the whole thickness and consisting of laser micromachined holes of 350.8 ± 16.6-micrometer diameter, whose centers were spaced 1312.0 ± 23.0 μm, were created. Both sol-gel based 3D scaffold configurations combined compressive strength in the range of 2–3 MPa and the biocompatibility of the hybrid material. In addition, the observed Si, Ca and P biodegradation provided a suitable microenvironment with significant focal adhesion development, maturation and also enhanced in vitro cell growth. In conclusion, this work successfully confirmed the feasibility of both strategies for the fabrication of new sol-gel-based hybrid scaffolds with osteoconductive properties.

Fabrication and Characterization of Bioactive Gelatin-Alginate-Bioactive Glass Composite Coatings on Porous Titanium Substrates

In this research work, the fabrication of biphasic composite implants has been investigated. Porous, commercially available pure Ti (50 vol % porosity and pore distributions of 100-200, 250-355, and 355-500 μm) has been used as a cortical bone replacement, while different composites based on a polymer blend (gelatin and alginate) and bioactive glass (BG) 45S5 have been applied as a soft layer for cartilage tissues. The microstructure, degradation rates, biofunctionality, and wear behavior of the different composites were analyzed to find the best possible coating. Experiments demonstrated the best micromechanical balance for the substrate containing 200-355 μm size range distribution. In addition, although the coating prepared from alginate presented a lower mass loss, the composite containing 50% alginate and 50% gelatin showed a higher elastic recovery, which entails that this type of coating could replicate the functions of the soft tissue in areas of the joints. Therefore, results revealed that the combinations of porous commercially pure Ti and composites prepared from alginate/gelatin/45S5 BG are candidates for the fabrication of biphasic implants not only for the treatment of osteochondral defects but also potentially for any other diseases affecting simultaneously hard and soft tissues.

Multifunctional polyethylene imine hybrids decorated by silica bioactive glass with enhanced mechanical properties, antibacterial, and osteogenesis for bone repair

Inorganic/organic hybrids and bioactive glasses demonstrate promising potential as bone substitute biomaterials. A sol-gel hybrid consisting of silica bioactive glass and biodegradable polymer can combine the high bioactivity of a glass with the toughness of a polymer. In this study, multifunctional hybrids with a combination of organic-inorganic hybrid structure class II consisting of polyethyleneimine (PEI) generation 4 (G4) and bioactive glass with enhanced mechanical properties, mineralization, antibacterial, and osteogenesis activities were synthesized by the sol-gel method. Glycidoxypropyl) trimethoxysilane (GPTMS) with different concentrations was used as a covalent bonding agent between PEI polymer and bioactive glass. The effect of GPTMS content was assessed in the presence and absence of calcium in the hybrid structures in terms of morphology, wettability, mechanical properties, antibacterial activity, cell viability, and in vitro osteogenic differentiation properties. By increasing the amount of GPTMS, the compressive strength increased from 1.95 MPa to 2.34 MPa, which was comparable to human trabecular bone. All the hybrids presented antibacterial activity against Staphylococcus aureus, forming an inhibition zone of 13-16 mm. An increase in cell viability of 82.22% in PSCaG90 was obtained after 1 day of MG-63 cell culture. Alkaline phosphatase expression and mineralization of MG-63 cells increased in the PSCaG90 hybrid in the absence of an osteogenic medium compared to PSG60 and PSG90. The PSCaG90 hybrid indicated considerable in vitro osteogenic capacity in the absence of a differentiation medium, expressing high levels of bone-specific proteins including collagen I (COL1A1), Runt-related transcription factor 2 (RUNX2), osteopontin (OPN), and osteocalcin (OCN), compared to calcium-free hybrids. Overall, our results suggest that the presence of calcium in the PSCaG90 leads to a significant increase in osteogenic differentiation of MG-63 cells even in the absence of differentiation medium, which suggests these hybrid structures with multifunctional properties as promising candidates for bone repair.