Nanomaterials-Based Ion-Imprinted Electrochemical Sensors for Heavy Metal Ions Detection: A Review

Application Prospect of Ion-Imprinted Polymers in Harmless Treatment of Heavy Metal Wastewater

With the rapid development of industry, the discharge of heavy metal-containing wastewater poses a significant threat to aquatic and terrestrial environments as well as human health. This paper provides a brief introduction to the basic principles of ion-imprinted polymer preparation and focuses on the interaction between template ions and functional monomers. We summarized the current research status on typical heavy metal ions, such as Cu(II), Ni(II), Cd(II), Hg(II), Pb(II), and Cr(VI), as well as metalloid metal ions of the As and Sb classes. Furthermore, it discusses recent advances in multi-ion-imprinted polymers. Finally, the paper addresses the challenges faced by ion-imprinted technology and explores its prospects for application.

Supramolecular Self-Assembled Nanostructures Derived from Amplified Structural Isomerism of Zn(II)-Sn(IV)-Zn(II) Porphyrin Triads and Their Visible Light Photocatalytic Degradation of Pollutants

Two structural isomeric porphyrin-based triads (Zn(II)porphyrin-Sn(IV)porphyrin-Zn(II)porphyrin) denoted as T1 and T2 were prepared from the reaction of meso-[5-(4-hydroxyphenyl)-10,15,20-tris(3,5-di-tert-butylphenyl)porphyrinato]zinc(II) (ZnL) with trans-dihydroxo-[5,10-bis(3-pyridyl)-15,20-bis(phenyl)porphyrinato]tin(IV) (SnP1) and trans-dihydroxo-[5,15-bis(3-pyridyl)-10,20-bis(phenyl)porphyrinato]tin(IV) (SnP2), respectively. All the compounds were characterized using UV-vis spectroscopy, emission spectroscopy, ESI-MS, 1H NMR spectroscopy, and FE-SEM. Most importantly, the two structurally isomeric porphyrin-based triads supramolecularly self-assembled into completely different nanostructures. T1 exhibits a nanosphere morphology, whereas T2 exhibits a nanofiber morphology. The amplified geometric feature in the structural isomeric porphyrin-based triads dictates the physical and chemical properties of the two triads. Both compounds showed the morphology-dependent visible light catalytic photodegradation of rhodamine B dye (74-97% within 90 min) and tetracycline antibiotic (44-71% within 45 min) in water. In both cases, the photodegradation efficiency of T2 was higher than that of T1. The present investigation can significantly contribute to the remediation of wastewater by tuning the conformational changes in porphyrin-based photocatalysts.

Electrochemical Sensors for Heavy Metal Ion Detection in Aqueous Medium: A Systematic Review

Heavy metal ions (HMIs) are very harmful to the ecosystem when they are present in excess of the recommended limits. They are carcinogenic in nature and can cause serious health issues. So, it is important to detect the metal ions quickly and accurately. The metal ions arsenic (As3+), cadmium (Cd2+), chromium (Cr3+), lead (Pb2+), and mercury (Hg2+) are considered to be very toxic among other metal ions. Standard analytical methods like atomic absorption spectroscopy, atomic fluorescence spectroscopy, and X-ray fluorescence spectroscopy are used to detect HMIs. But these methods necessitate highly technical equipment and lengthy procedures with skilled personnel. So, electrochemical sensing methods are considered to be more advantageous because of their quick analysis with precision and simplicity to operate. They can detect a wide range of heavy metals providing real-time monitoring and are cost-effective and enable multiparametric detection. Various sensing applications necessitate severe regulation regarding the modification of electrode surfaces. Numerous nanomaterials such as graphene, carbon nanotubes, and metal nanoparticles have been extensively explored as interface materials in electrode modifiers. These nanoparticles offer excellent electrical conductivity, distinctive catalytic properties, and high surface area resulting in enhanced electrochemical performance. This review examines different HMI detection methods in an aqueous medium by an electrochemical sensing approach and studies the recent developments in interface materials for altering the electrodes.

The complexometric behavior of selected aroyl-S,N-ketene acetals shows that they are more than AIEgens

Using the established synthetic methods, aroyl-S,N-ketene acetals and subsequent bi- and multichromophores can be readily synthesized. Aside from pronounced AIE (aggregation induced emission) properties, these selected examples possess distinct complexometric behavior for various metals purely based on the underlying structural motifs. This affects the fluorescence properties of the materials which can be readily exploited for metal ion detection and for the formation of different metal-aroyl-S,N-ketene acetal complexes that were confirmed by Job plot analysis. In particular, gold(I), iron(III), and ruthenium (III) ions reveal complexation enhanced or quenched emission. For most dyes, weakly coodinating complexes were observed, only in case of a phenanthroline aroyl-S,N-ketene acetal multichromophore, measurements indicate the formation of a strongly coordinating complex. For this multichromophore, the complexation results in a loss of fluorescence intensity whereas for dimethylamino-aroyl-S,N-ketene acetals and bipyridine bichromophores, the observed quantum yield is nearly tripled upon complexation. Even if no stable complexes are formed, changes in absorption and emission properties allow for a simple ion detection.

Recent advance of nanomaterials modified electrochemical sensors in the detection of heavy metal ions in food and water

As one of the main pollutants, heavy metal ions can accumulate in the human body and cause a cascade of damage. Electrochemical sensors provide great prospects for tracing heavy metal ions because of their properties of high sensitivity, low detection limits and fast response. Electrode surface modification materials play a key role in enhancing the performance of electrochemical sensors. Herein, we summarize in detail the recent work on electrochemical sensors modified by carbon nanomaterials (graphene and its derivatives, carbon nanofibers and carbon nanotubes), metal nanomaterials (gold, silver, bismuth and iron), complexes (MOFs, ZIFs and MXenes) and their composites for the detection of heavy metal ions (mainly include Cd(II), Hg(II), Pb(II), As(III), Cu(II) and Zn(II)) in food and water. The synthetic strategies, mechanisms, innovations, advantages, challenges and prospects of various electrode modification nanomaterials for the detection of heavy metal ions in food and water are discussed.

High Selectivity and Sensitivity in Chemiresistive Sensing of Co(II) Ions with Liquid-Phase Exfoliated Functionalized MoS2 : A Supramolecular Approach

Chemical sensing of water contamination by heavy metal ions is key as it represents a most severe environmental problem. Liquid-phase exfoliated two-dimensional (2D) transition metal dichalcogenides (TMDs) are suitable candidates for chemical sensing thanks to their high surface-to-volume ratio, sensitivity, unique electrical characteristics, and scalability. However, TMDs lack selectivity due to nonspecific analyte-nanosheet interactions. To overcome this drawback, defect engineering enables controlled functionalization of 2D TMDs. Here, ultrasensitive and selective sensors of cobalt(II) ions via the covalent functionalization of defect-rich MoS2 flakes with a specific receptor, 2,2':6',2″-terpyridine-4'-thiol is developed. A continuous network is assembled by healing of MoS2 sulfur vacancies in a tailored microfluidic approach, enabling high control over the assembly of thin and large hybrid films. The Co2+ cations complexation represents a powerful gauge for low concentrations of cationic species which can be best monitored in a chemiresisitive ion sensor, featuring a 1 pm limit of detection, sensing in a broad concentration range (1 pm - 1 µm) and sensitivity as high as 0.308 ± 0.010 lg([Co2+ ])-1 combined with a high selectivity towards Co2+ over K+ , Ca2+ , Mn2+ , Cu2+ , Cr3+ , and Fe3+ cations. This supramolecular approach based on highly specific recognition can be adapted for sensing other analytes through specific ad-hoc receptors.

Recent Advances in and Applications of Electrochemical Sensors Based on Covalent Organic Frameworks for Food Safety Analysis

The international community has been paying close attention to the issue of food safety as a matter of public health. The presence of a wide range of contaminants in food poses a significant threat to human health, making it vital to develop detection methods for monitoring these chemical contaminants. Electrochemical sensors using emerging materials have been widely employed to detect food-derived contaminants. Covalent organic frameworks (COFs) have the potential for extensive applications due to their unique structure, high surface area, and tunable pore sizes. The review summarizes and explores recent advances in electrochemical sensors modified with COFs for detecting pesticides, antibiotics, heavy metal ions, and other food contaminants. Furthermore, future challenges and possible solutions will be discussed regarding food safety analysis using COFs.

Synthesis, Characterization, and Applications of Nanomaterials for Energy Conversion and Storage

Ever since the commencement of the Industrial Revolution in Great Britain in the mid-18th century, the annual global energy consumption from various fossil fuels, encompassing wood, coal, natural gas, and petroleum, has demonstrated an exponential surge over the past four centuries [...].

Fabrication of magneticα-Fe2O3/Fe3O4heterostructure nanorods via the urea hydrolysis-calcination process and their biocompatibility with LO2and HepG2cells

β-FeOOH nanorods were prepared via the urea hydrolysis process with the average length of 289.1 nm and average diameter of 61.2 nm, while magneticα-Fe2O3/Fe3O4heterostructure nanorods were prepared via the urea calcination process withβ-FeOOH nanorods as precursor, and the optimum conditions were the calcination temperature of 400 °C, the calcination time of 2 h, theβ-FeOOH/urea mass ratio of 1:6. The average length, diameter, and the saturation magnetization of the heterostructure nanorods prepared under the optimum conditions were 328.8 nm, 63.4 nm and 42 emu·g-1, respectively. The Prussian blue test demonstrated that the heterostructure nanorods could be taken up by HepG2 cells, and cytotoxicity tests proved that the heterostructure nanorods had no significant effect on the viabilities of LO2 and HepG2 cells within 72 h in the range of 100-1600μg·ml-1. Therefore, magneticα-Fe2O3/Fe3O4heterostructure nanorods had better biocompatibility with LO2 and HepG2 cells.

Molecularly Imprinted Polymer-Based Biomimetic Systems for Sensing Environmental Contaminants, Biomarkers, and Bioimaging Applications

Molecularly imprinted polymers (MIPs), a biomimetic artificial receptor system inspired by the human body's antibody-antigen reactions, have gained significant attraction in the area of sensor development applications, especially in the areas of medical, pharmaceutical, food quality control, and the environment. MIPs are found to enhance the sensitivity and specificity of typical optical and electrochemical sensors severalfold with their precise binding to the analytes of choice. In this review, different polymerization chemistries, strategies used in the synthesis of MIPs, and various factors influencing the imprinting parameters to achieve high-performing MIPs are explained in depth. This review also highlights the recent developments in the field, such as MIP-based nanocomposites through nanoscale imprinting, MIP-based thin layers through surface imprinting, and other latest advancements in the sensor field. Furthermore, the role of MIPs in enhancing the sensitivity and specificity of sensors, especially optical and electrochemical sensors, is elaborated. In the later part of the review, applications of MIP-based optical and electrochemical sensors for the detection of biomarkers, enzymes, bacteria, viruses, and various emerging micropollutants like pharmaceutical drugs, pesticides, and heavy metal ions are discussed in detail. Finally, MIP's role in bioimaging applications is elucidated with a critical assessment of the future research directions for MIP-based biomimetic systems.

Electrochemical System for Field Control of Hg2+ Concentration in Wastewater Samples

The paper presents the validation of an electrochemical procedure for on-site Hg²⁺ ions determination in wastewater samples using a modified carbon screen-printed electrode (SPE) with a complexing polymeric film based on poly(2,2'-(ethane-1,2-diylbis((2-(azulen-2-ylamino)-2-oxoethyl)azanediyl))diacetic acid) (polyL). Using metal ions accumulation in an open circuit followed by anodic stripping voltammetry, the SPE-polyL electrode presents a linear range in the range of 20 µg/L to 150 µg/L, with a limit of detection (LOD) = 6 µg/L, limit of quantification (LOQ) = 20 µg/L, and an average measurement uncertainty of 26% of mercury ions. The results obtained in situ and in the laboratory using the SPE-polyL modified electrode were compared with those obtained by the atomic absorption spectrometry coupled with the cold vapor generation standardized method, with the average values indicating excellent recovery yields.