Advanced Catalytic Materials for Ethanol Oxidation in Direct Ethanol Fuel Cells

Optimized Electrodeposition of Ni2O3 on Carbon Paper for Enhanced Electrocatalytic Oxidation of Ethanol

The urgent need for sustainable and efficient energy conversion technologies has propelled research into novel electrocatalysts for fuel cell applications. This study investigates a carbon paper (CP)-supported Ni2O3 catalyst for the electrocatalytic oxidation of ethanol. We utilized electrodeposition to uniformly deposit/dop Ni2O3 onto the CP, creating an effective electrocatalyst. Our approach allows the tailoring of the doping degree by adjusting the electrodeposition potential. The optimal doping degree, achieved at a medium deposition potential, results in an electrode with high intrinsic activity and a substantial electrochemically active surface area (ECSA), thereby enhancing its electrocatalytic activity. This catalyst efficiently facilitates the oxidation of ethanol to formic acid while maintaining good stability. The enhanced performance is attributed to the effective interface and interaction between Ni2O3 and CP. This work not only provides insights into the design of efficient Ni-based catalysts for ethanol oxidation but also paves the way for developing advanced materials for renewable energy conversion.

Facile Synthesis of High-Entropy Alloy Nanowires for Electrocatalytic Alcohol Oxidation

Considering the structural and compositional advantages of high-entropy alloy (HEA) as high-efficient electrocatalysts, we here present a facile method to prepare high-entropy alloy nanowires with seven elements in an aqueous solution. The as-synthesized PdPtCuAgAuPbCo nanowires possess dispersed one-dimensional morphology and exhibit enhanced electrocatalytic performance with the mass activity of 9.9 A mgPd+Pt -1 toward ethanol electrooxidation. The HEA nanowires also perform superior stability, resistance to CO poisoning, and good electrocatalytic activities toward other alcohols (e. g., ethylene glycol and methanol) oxidation. The synthesis strategy is easy to operate with low cost and has wide application prospects for preparing desired electrocatalysts for fuel cells.

Laser Irradiation Synthesis of AuPd Alloy with Decreased Alloying Degree for Efficient Ethanol Oxidation Reaction

The preparation of electrocatalysts with high performance for the ethanol oxidation reaction is vital for the large-scale commercialization of direct ethanol fuel cells. Here, we successfully synthesized a high-performance electrocatalyst of a AuPd alloy with a decreased alloying degree via pulsed laser irradiation in liquids. As indicated by the experimental results, the photochemical effect-induced surficial deposition of Pd atoms, combined with the photothermal effect-induced interdiffusion of Au and Pd atoms, resulted in the formation of AuPd alloys with a decreased alloying degree. Structural characterization reveals that L-AuPd exhibits a lower degree of alloying compared to C-AuPd prepared via the conventional co-reduction method. This distinct structure endows L-AuPd with outstanding catalytic activity and stability in EOR, achieving mass and specific activities as high as 16.01 A mgPd-1 and 20.69 mA cm-2, 9.1 and 5.2 times than that of the commercial Pd/C respectively. Furthermore, L-AuPd retains 90.1% of its initial mass activity after 300 cycles. This work offers guidance for laser-assisted fabrication of efficient Pd-based catalysts in EOR.

Ultrafast synthesis of efficient TS-PtCoCu/CNTs composite with high feed-to-product conversion rate by Joule heating for electrocatalytic oxidation of ethanol

Due to the challenges involved in achieving high metal load, uniform metal dispersion and nanosized metal particles simultaneously, it is difficult to develop a simple protocol for the rapid and efficient synthesis of Pt-based composites for electrocatalytic ethanol oxidation reaction (EOR). In this study, a facile ultrafast thermal shock strategy via Joule heating was applied to fabricate a series of PtCoCu ternary nanoalloys decorated carbon nanotube composites (TS-PtCoCu/CNTs), without the need for a reducing agent or surfactant. The TS-PtCoCu/CNTs with optimal Pt content (∼15 %) exhibited excellent EOR activity, with mass and specific activity of 3.58 A mgPt-1 and 5.79 mA cm-2, respectively, which are 3.8 and 13.5 times higher than those of Pt/C. Compared with the control prepared through the traditional furnace annealing, the catalyst also showed excellent activity and stability. DFT calculations revealed that the TS-PtCoCu/CNTs possesses a downshifted d-band center, weakened CO adsorption and higher OH affinity compared with monometallic Pt, all of which lead to the preferred C1 pathway for EOR. This study demonstrates an ultrafast construction of a highly efficient Pt-Co-Cu ternary catalyst for EOR. Additionally, it provides insights into the reaction mechanism based on structural characterization, electrochemical characterization, and theoretical calculations.

Electrodeposition-Assisted Crystal Growth Regulation of PdBi Clusters on Carbon Cloths for Ethanol Oxidation

Carbon-supported Pd-based clusters are one of the most promising anodic catalysts for ethanol oxidation reaction (EOR) due to their encouraging activity and practical applications. However, unclear growth mechanism of Pd-based clusters on the carbon-based materials has hindered their extensive applications. Herein, we first introduce multi-void spherical PdBi cluster/carbon cloth (PdBi/CC) composites by an electrodeposition routine. The growth mechanism of PdBi clusters on the CC supports has been systemically investigated by evaluating the selected samples and tuning their compositions, which involve the big difference in standard redox potential between Pd2+/Pd and Bi3+/Bi and easy adsorption of Bi3+ on the surface of Pd-rich seeds. Benefitting from the ensembles of many nanocrystal subunits, multi-void spherical PdBi clusters can present collective properties and novel functionalities. In addition, the outstanding characteristics of CC supports enable PdBi clusters with stable nanostructures. Thanks to the unique structure, Pd20Bi/CC catalysts manifest higher EOR activity and better stability compared to Pd/CC. Systematic characterizations and a series of CO poisoning tests further confirm that the dramatically enhanced EOR activity and stability can be attributed to the incorporation of Bi species and the strong coupling of the structure between PdBi clusters and CC supports.

Wet-chemistry synthesis of two-dimensional Pt- and Pd-based intermetallic electrocatalysts for fuel cells

Two-dimensional (2D) noble-metal-based nanomaterials have attracted tremendous attention and have widespread promising applications as a result of their unique physical, chemical, and electronic properties. Especially, 2D Pt- and Pd-based intermetallic nanoplates (IMNPs) and nanosheets (IMNSs) are widely studied for fuel cell (FC)-related reactions, including the cathodic oxygen reduction reaction (ORR) and anodic formic acid, methanol and ethanol oxidation reactions (FAOR, MOR and EOR). Wet-chemistry synthesis is a powerful strategy to prepare metallic nanocrystals with well-controlled dispersity, size, and composition. In this review, a fundamental understanding of the FC-related reactions is firstly elaborated. Subsequently, the current wet-chemistry synthesis pathways for 2D Pt- and Pd-based IMNPs and IMNSs are briefly summarized, as well as their electrocatalytic applications including in the ORR, FAOR, MOR, and EOR. Finally, we provide an overview of the opportunities and current challenges and give our perspectives on the development of high-performance 2D Pt- and Pd-based intermetallic electrocatalysts towards FCs. We hope this review offers timely information on the synthesis of 2D Pt- and Pd-based IMNPs and IMNSs and provides guidance for the efficient synthesis and application of them.

Ethanol Oxidation via 12-Electron Pathway on Spiky Au@AuPd Nanoparticles Assisted by Near-Infrared Light

In this work, ethanol oxidation reaction (EOR) via 12-electron (C1-12e) pathway on spiky Au@AuPd nanoparticles (NPs) with ultrathin AuPd alloy shells is achieved in alkaline media with the assistance of the near-infrared (NIR) light. It is found that OH radicals can be produced from the OH_ads species adsorbed on the surfaces of Pd atoms led by surface plasmon resonance (SPR) effect of spiky Au@AuPd NPs under the irradiation of NIR light. Moreover, OH radicals play the key role for the achievement of EOR proceeded by the desirable C1-12e pathway because OH radicals can directly break the C-C bonds of ethanol. Accordingly, the electrocatalytic performance of spiky Au@AuPd NPs toward EOR under NIR light is greatly improved. For instance, their mass activity can be up to 33.2 A mg_pd ^-1 in the 0.5 m KOH solution containing 0.5 m ethanol, which is about 158 times higher than that of commercial Pd/C catalysts (0.21 A mg_pd ^-1 ) and is better than those of the state-of-the-art Pd-based catalysts reported in literature thus far, to the best of our knowledge. Moreover, their highest mass activity can be further improved to 118.3 A mg_pd ^-1 in the 1.5 m KOH solution containing 1.25 m ethanol.

ZIF-67-Derived NiCo-Layered Double Hydroxide@Carbon Nanotube Architectures with Hollow Nanocage Structures as Enhanced Electrocatalysts for Ethanol Oxidation Reaction

The rational design of efficient Earth-abundant electrocatalysts for the ethanol oxidation reaction (EOR) is the key to developing direct ethanol fuel cells (DEFCs). Among these, the smart structure is highly demanded for highly efficient and stable non-precious electrocatalysts based on transition metals (such as Ni, Co, and Fe). In this work, high-performance NiCo-layered double hydroxide@carbon nanotube (NiCo-LDH@CNT) architectures with hollow nanocage structures as electrocatalysts for EOR were prepared via sacrificial ZIF-67 templates on CNTs. Comprehensive structural characterizations revealed that the as-synthesized NiCo-LDH@CNTs architecture displayed 3D hollow nanocages of NiCo-LDH and abundant interfacial structure between NiCo-LDH and CNTs, which could not only completely expose active sites by increasing the surface area but also facilitate the electron transfer during the electrocatalytic process, thus, improving EOR activity. Benefiting from the 3D hollow nanocages and interfacial structure fabricated by the sacrificial ZIF-67-templated method, the NiCo-LDH@CNTs-2.5% architecture exhibited enhanced electrocatalytic activity for ethanol oxidation compared to single-component NiCo-LDH, where the peak current density was 11.5 mA·cm^-2, and the j_f/j_b value representing the resistance to catalyst poisoning was 1.72 in an alkaline environment. These results provide a new perspective on the fabrication of non-precious metal electrocatalysts for EOR in DEFCs.

Promoting the Electrocatalytic Ethanol Oxidation Activity of Pt by Alloying with Cu

The development and commercialization of direct ethanol fuel cells requires active and durable electro-catalysts towards the ethanol oxidation reactions (EOR). Rational composition and morphology control of Pt-based alloy nanocrystals can not only enhance their EOR reactivity but also reduce the consumption of precious Pt. Herein, PtCu nanocubes (NCs)/CB enclosed by well-defined (100) facets were prepared by solution synthesis, exhibiting much higher mass activity (4.96 A mgPt−1) than PtCu nanoparticles (NPs)/CB with irregular shapes (3.26 A mgPt−1) and commercial Pt/C (1.67 A mgPt−1). CO stripping and in situ Fourier transform infrared spectroscopy (FTIR) experiments indicate that the alloying of Cu enhanced the adsorption of ethanol, accelerated the subsequent oxidation of intermediate species, and increased the resistance to CO poisoning of PtCu NCs/CB, as compared with commercial Pt/C. Therefore, alloying Pt with earth-abundant Cu under rational composition and surface control can optimize its surface and electronic structures and represents a promising strategy to promote the performance of electro-catalysts while reduce the use of precious metals.

Ethanol Electrooxidation at 1-2 nm AuPd Nanoparticles

We report a systematic study of the electrocatalytic properties and stability of a series of 1-2 nm Au, Pd, and AuPd alloy nanoparticles (NPs) for the ethanol oxidation reaction (EOR). Following EOR electrocatalysis, NP sizes and compositions were characterized using aberration-corrected scanning transmission electron microscopy (ac-STEM) and energy dispersive spectroscopy (EDS). Two main findings emerge from this study. First, alloyed AuPd NPs exhibit enhanced electrocatalytic EOR activity compared to either monometallic Au or Pd NPs. Specifically, NPs having a 3:1 ratio of Au:Pd exhibit an ~8-fold increase in peak current density compared to Pd NPs, with an onset potential shifted ~200 mV more to the negative compared to Au NPs. Second, the size and composition of AuPd alloy NPs do not (within experimental error) change following 1.0 or 2.0 h chronoamperometry experiments, while monometallic Au NPs increase in size from 2 to 5 nm under the same conditions. Notably, this report demonstrates the importance of post-catalytic ac-STEM/EDS characterization for fully evaluating NP activity and stability, especially for 1-2 nm NPs that may change in size or structure during electrocatalysis.

Passive Small Direct Alcohol Fuel Cells for Low-Power Portable Applications: Assessment Based on Innovative Increments since 2018

Passive small direct alcohol fuel cells (PS-DAFCs) are compact, standalone devices capable of electrochemically converting the chemical energy in the fuel/alcohol into electricity, with low pollutant emissions and high energy density. Thus, PS-DAFCs are extremely attractive as sustainable/green off-grid low-power sources (milliwatts to watts), considered as alternatives to batteries for small/portable electric and electronic devices. PS-DAFCs benefit from long life operation and low cost, assuring an efficient and stable supply of inherent non-polluting electricity. This review aims to assess innovations on PS-DAFC technology, as well as discuss the challenges and R&D needs covered on practical examples reported in the scientific literature, since 2018. Hence, this compilation intends to be a guidance tool to researchers, in order to help PS-DAFCs overcome the barriers to a broad market introduction and consequently become prime renewable energy converters and autonomous micropower generators. Only by translating research discoveries into the scale-up and commercialization process of the technology can the best balance between the economic and technical issues such as efficiency, reliability, and durability be achieved. In turn, this will certainly play a crucial role in determining how PS-DAFCs can meet pressing sustainable energy needs.

In-Situ surface enhanced infrared absorption spectroscopy study of electrocatalytic oxidation of ethanol on Platinum/Gold surface

The behavior of ethanol oxidation reaction on composite electrodes prepared by deposition platinum on a gold surface (Pt/Au) were studied by cyclic voltammetry and surface enhanced infrared absorption spectroscopy (SEIRAS) analysis. The results show that the Pt electrode has high oxidation activity and significant poison behavior; on the contrary, the Au electrode demonstrates low activity without a poison peak. The SEIRAS analyses reveal that both carbon monoxide (CO) and carbon dioxide (CO₂) appear during anode sweeping, and the CO peak density decreases with increasing potential and finally is eliminated. During the cathodic scanning, the CO peak reappears, and the peak intensity increases with scanning cycles, demonstrating a high poison behavior and the C1 reaction route on Pt. On the Au electrode, CO₂ and CO peaks were not observed; instead, an acetic acid peak appeared, indicating a C2 reaction path. For the Pt/Au composited electrodes, the electrochemical activities of the electrodes, as well as their poison behavior, increased with the deposition amount of Pt. However, the intensities of the poison peaks are smaller than those of oxidation ones; therefore, a higher tolerance to the CO poison can be achieved. For the 2 m-Pt/Au composite electrode, the activity is close to that of pure Pt, but the poison tolerance is 3 times the value of Pt.

Enhanced Electrocatalytic Oxidation of Small Organic Molecules on Platinum-Gold Nanowires: Influence of the Surface Structure and Pt-Pt/Pt-Au Pair Site Density

The electrochemical oxidation of small organic molecules (SOMs) such as methanol and glucose is a critical process and has relevant applications in fuel cells and sensors. A key challenge in SOM oxidation is the poisoning of the surface by carbon monoxide (CO) and other partially oxidized intermediates, which is attributed to the presence of Pt-Pt pair sites. A promising pathway for overcoming this challenge is to develop catalysts that selectively oxidize SOMs via "direct" pathways that do not form CO as a primary intermediate. In this report, we utilize an ambient, template-based approach to prepare PtAu alloy nanowires with tunable compositions. X-ray photoelectron spectroscopy measurements reveal that the surface composition matches that of the bulk composition after synthesis. Monte Carlo method simulations of the surface structure of PtAu alloys with varying coverage of oxygen adsorbates and varying degrees of oxygen adsorption strength reveal that oxygen adsorption under electrochemical conditions enriches the surface with Pt and a large fraction of Pt-Pt sites remain on the surface even with the Au content of up to 50%. Electrochemical properties and the catalytic performance measurements of the PtAu nanowires for the oxidation of methanol and glucose reveal that the mechanistic pathways that produce CO are suppressed by the addition of relatively small quantities of Au (∼10%), and CO formation can be completely suppressed by 50% Au. The suppression of CO formation with small quantities of Au suggests that the presence of Pt-Au pair sites may be more important in determining the mechanism of SOM oxidation rather than Pt-Pt pair site density.

Mxene coupled over nitrogen-doped graphene anchoring palladium nanocrystals as an advanced electrocatalyst for the ethanol electrooxidation

Development of good support materials is widely adopted as a valid strategy to fabricate high performance electrocatalysts for the ethanol oxidation reaction (EOR). In this study, the small diameter Ti₃C₂T_x MXene thin nanosheets inserted into three-dimensional nitrogen-doped grapheme (NG) was constructed via a facile hydrothermal method and employed as support materials for anchoring Pd nanocrystals (Pd/Ti₃C₂T_x@NG). The obtained-Pd/Ti₃C₂T_x@NG as EOR electrocatalyst in alkaline media outperforms the commercial Pd/C with better electrocatalytic activity, enhanced long-term stability and high CO tolerance. The Ti₃C₂T_x inserted into NG probably plays a key role for enhancing the properties of the synthesized-catalyst. Inserting Ti₃C₂T_x into NG allows the electrocatalysts to have high porosity, surface hydrophilicity, sufficient number of anchor sites for Pd nanocrystals and modifies its electronic properties, which can promote the electrocatalytic activity and durability. The enhanced EOR performance endows Pd/Ti₃C₂T_x@NG with great application potential in fuel cells as an anode catalyst. Furthermore, the prepared Ti₃C₂T_x@NG is also suitable in various desired applications, especially other oxidation reactions.

Surface Engineering of Flower-Like Ionic Liquid-Functionalized Graphene Anchoring Palladium Nanocrystals for a Boosted Ethanol Oxidation Reaction

The development of low-cost and high-performance electrocatalyst-supporting materials is desirable and necessary for the ethanol oxidation reaction (EOR). Here, we report a facile and universal template-free approach for the first time to synthesize three-dimensional (3D) flower-like ionic liquid-functionalized graphene (IL-RGO). Then, the crystalline Pd nanoparticles were anchored on IL-RGO by a simple wet chemical growth method without a surfactant (denoted as Pd/IL-RGO). In particular, the IL is conducive to form a 3D flower-like structure. The optimized Pd/IL-RGO-2 presents a much-promoted electrocatalytic performance toward the EOR compared with commercial Pd/C catalysts, which is mainly derived from the grafted IL on RGO and the unique 3D flower-like structure. In detail, the IL can control, stabilize, and disperse the Pd nanocrystals as well as serving as the solvent and electrolyte in the microenvironment of the EOR, and the 3D flower-like structure endows the Pd/IL-RGO with high surface areas and rich opened channels, thereby kinetically accelerating the charge/mass transfers. Furthermore, density functional theory calculations reveal that the strong electronic interaction between Pd and IL-RGO generates a downshift of d_center for Pd and thereby enhances the durability toward CO-like intermediates and electrocatalytic reaction kinetics.

Pt3Sn nanoparticles enriched with SnO2/Pt3Sn interfaces for highly efficient alcohol electrooxidation

Pt₃Sn nanoparticles (NPs) enriched with Pt₃Sn/ultra-small SnO₂ interfaces (Pt₃Sn@u-SnO₂/NG) were synthesized through a thermal treatment of Pt₂Sn/NG in a H₂ atmosphere, followed by annealing under H₂ and air conditions. The unique structure of Pt₃Sn NPs enriched with Pt₃Sn/SnO₂ interfaces was observed on the Pt₃Sn@u-SnO₂/NG catalyst based on HRTEM. The optimized Pt₃Sn@u-SnO₂/NG catalyst achieves high catalytic activity with an ethanol oxidation reaction (EOR) activity of 366 mA mg_Pt ^-1 and a methanol oxidation reaction (MOR) activity of 503 mA mg_Pt ^-1 at the potential of 0.7 V, which are eight-fold and five-fold higher than those for the commercial Pt/C catalyst (44 and 99 mA mg_Pt ^-1, respectively). The Pt₃Sn@u-SnO₂/NG catalyst is found to be 3 times more stable and have higher CO tolerance than Pt/C. The outstanding performance of the Pt₃Sn@u-SnO₂/NG catalyst should be ascribed to the synergetic effect induced by the unique structure of Pt₃Sn NPs enriched with Pt₃Sn/SnO₂ interfaces. The synergetic effect between Pt₃Sn NPs and ultra-small SnO₂ increases the performance for alcohol oxidation because the Sn in both Pt₃Sn and SnO₂ favors the removal of CO_ads on the nearby Pt by providing OH_ads species at low potentials. The present work suggests that the Pt₃Sn@u-SnO₂ is indeed a unique kind of efficient electrocatalyst for alcohol electrooxidation.

An evaluation of solvent effects and ethanol oxidation

Understanding liquid-metal interfaces in catalysis is important, as the liquid can speed up surface reactions, increase the selectivity of products, and open up new favorable reaction pathways. In this work we modeled using density functional theory various steps in ethanol oxidation/decomposition over Rh(111). We considered implicit (continuum), explicit, and hybrid (implicit combined with explicit) solvation approaches, as well as two solvents, water and ethanol. We focused on modeling adsorption steps, as well as C-C/C-H bond scission and C-O bond formation reactions. Implicit solvation had very little effect on adsorption and reaction free energies. However, using the explicit and hybrid models, some free energies changed significantly. Furthermore, ethanol solvent had a more considerable impact than water solvent. We observed that preferred reaction pathways for C-C scission changed depending on the solvation model and solvent choice (ethanol or water). We also applied the bond-additivity solvation method to calculate heats of adsorption. Heats of adsorption and reaction using the bond-additivity model followed the same trends as the other solvation models, but were ∼1.1 eV more endothermic. Our work highlights how different solvation approaches can influence analysis of the oxidation/decomposition of organic surface species.

Boosting Transport Kinetics of Cobalt Sulfides Yolk-Shell Spheres by Anion Doping for Advanced Lithium and Sodium Storage

Cobalt sulfides have been popularly used in energy storage because of their high theoretical capacity and abundant redox reactions. However, poor reaction kinetics, rapid capacity decay, and severe polarization owing to volume changes during electrochemical reaction are still huge challenges for cobalt sulfides in practical applications. Herein, cobalt sulfide yolk-shell spheres were synthesized by phosphorus doping (P-CoS) to stabilize the structure of cobalt sulfides and improve their electronic/ion conductivity. Kinetic tests and density functional theory calculations confirm that the introduction of phosphorus into cobalt sulfides greatly reduces the diffusion barrier of Li⁺ in the intrinsic structure, thereby improving the reaction kinetics of electrode materials during the Li⁺ insertion/extraction process. In consequence, the P-CoS electrode delivers a high lithium storage capacity (781 mAh g^-1 after 100 cycles at 0.2 A g^-1 ), excellent rate capability (489 mAh g^-1 at 10 A g^-1 ), and outstanding cycling stability (no significant capacity decay over 4000 cycles at 5 A g^-1 ). Especially for sodium-ion battery application, the P-CoS electrode expresses a striking capacity of approximately 260 mAh g^-1 at 2 A g^-1 after 900 cycles.

Bismuth as Smart Material and Its Application in the Ninth Principle of Sustainable Chemistry

This paper reports an overview of Green Chemistry and the concept of its twelve principles. This study focusses on the ninth principle of Green Chemistry, that is, catalysis. A report on catalysis, in line with its definition, background, classification, properties, and applications, is provided. The study also entails a green element called bismuth. Bismuth’s low toxicity and low cost have made researchers focus on its wide applications in catalysis. It exhibits smartness in all the catalytic activities with the highest catalytic performance among other metals.

Plasma-assisted nitrogen doping in Ni-Co-P hollow nanocubes for efficient hydrogen evolution electrocatalysis

To surmount the issues of a limited specific surface area and slow electrolyte diffusion in composite electrocatalysts, three-dimensional (3D) porous hollow nanocubes are fabricated, in which bimetal Ni-Co phosphide composites are covered with nanoparticles. The abundant hollow space provides more active sites for the catalyst, and simultaneously ensures efficient mass transfer and electron transport during the hydrogen evolution reaction (HER). A plasma-assisted approach is employed for smart N-doping in the Ni-Co phosphide hollow nanocubes (N-Ni-Co-P HNCs). The N-Ni-Co-P HNC catalyst exhibits a remarkable HER performance in 1 M KOH, evidenced by the low overpotentials of 47.9 mV and 150.5 mV at the current density of 10 mA cm-2 and 50 mA cm-2, respectively, as well as the excellent long-time stability. Essentially, the N doping tailors the electronic states and optimizes the free energy of hydrogen adsorption (ΔGH*) greatly, and the 3D porous hollow structure with porous nanoparticles stacked enlarges the specific active area substantially. Their synergistic effects result in the remarkably enhanced catalytic activity for the HER.

Unveiling a bimetallic FeCo-coupled MoS2 composite for enhanced energy storage

Sodium and potassium-ion batteries are promising for energy storage owing to their source abundance and low cost; however, most active materials still suffer from sluggish kinetics, huge volume variations, and poor conductivity and cycle stability. It remains a great challenge to explore appropriate electrode materials for scaled practical applications. Herein, mesoporous FeCo-incorporated MoS₂ nanosheets encapsulated into a porous carbon framework (FeCo@C@MoS₂) are smartly designed, artistically fabricated and evaluated for sodium and potassium storage. The FeCo@C@MoS₂ electrode displays high reversible capacities of 380 mA h g^-1 and 147 mA h g^-1 at 500 mA g^-1 for sodium and potassium storage, respectively. FeCo derived from a Prussian blue analogue promotes fast reaction kinetics of Na⁺/K⁺ transport, introduces the formation of a stable solid electrolyte interphase layer (SEI) in both the interior and exterior of the cube-like porous nanostructure and controls the Na⁺/K⁺ fluxes, suppressing the growth of metal dendrites. The porous carbon framework with large interstitial voids can effectively buffer volume variations and mitigate mechanical stress, contributing significantly to alleviate strain intensification on the surface layer between MoS₂ and FeCo during repeated plating/stripping processes. Density functional theoretical calculations (DFT) further confirm that the synthesized nanostructure shows an intensified electron state, elevated anti-stress ability, high-quality SEI film and preferable Na⁺/K⁺ adsorption energies. This in-depth investigation of the electrochemical performance and the extended energy storage mechanism based on metal alloy/sulfide nanostructures for sodium and potassium storage provides guidance for the smart design of heterojunctions for remarkable energy storage.

Ethanol Electrooxidation at Platinum-Rare Earth (RE = Ce, Sm, Ho, Dy) Binary Alloys

Proton exchange membrane fuel cells and direct alcohol fuel cells have been extensively studied over the last three decades or so. They have emerged as potential systems to power portable applications, providing clean energy, and offering good commercial viability. Ethanol is considered one of the most interesting fuels in this field. Herein, platinum-rare earth (Pt-RE) binary alloys (RE = Ce, Sm, Ho, Dy, nominal composition 50 at.% Pt) were produced and studied as anodes for ethanol oxidation reaction (EOR) in alkaline medium. A Pt-Dy alloy with nominal composition 40 at.% Pt was also tested. Their electrocatalytic performance was evaluated by voltammetric and chronoamperometric measurements in 2 M NaOH solution with different ethanol concentrations (0.2–0.8 M) in the 25–45 °C temperature range. Several EOR kinetic parameters were determined for the Pt-RE alloys, namely the charge transfer and diffusion coefficients, and the number of exchanged electrons. Charge transfer coefficients ranging from 0.60 to 0.69 and n values as high as 0.7 were obtained for the Pt0.5Sm0.5 electrode. The EOR reaction order at the Pt-RE alloys was found to vary between 0.4 and 0.9. The Pt-RE electrodes displayed superior performance for EOR than bare Pt, with Pt0.5Sm0.5 exhibiting the highest electrocatalytic activity. The improved electrocatalytic activity in all of the evaluated Pt-RE binary alloys suggests a strategy for the solution of the existing anode issues due to the structure-sensitive EOR.

Facile synthesis of PdAg nanocatalysts on CeO2/C composite supports as high-performance catalysts toward alkaline ethanol electro-oxidation

PdAg nanocatalysts on CeO₂/C supports were prepared using a facile, environment-friendly method and exhibited superior performance for ethanol electro-oxidation.