Mesoporous Silica-Supported Ionic Liquids as Catalysts for Styrene Carbonate Synthesis from CO2

Deep Eutectic Solvents as Catalysts for Cyclic Carbonates Synthesis from CO2 and Epoxides

In recent years, the chemical industry has put emphasis on designing or modifying chemical processes that would increasingly meet the requirements of the adopted proecological sustainable development strategy and the principles of green chemistry. The development of cyclic carbonate synthesis from CO₂ and epoxides undoubtedly follows this trend. First, it represents a significant improvement over the older glycol phosgenation method. Second, it uses renewable and naturally abundant carbon dioxide as a raw material. Third, the process is most often solvent-free. However, due to the low reactivity of carbon dioxide, the process of synthesising cyclic carbonates requires the use of a catalyst. The efforts of researchers are mainly focused on the search for new, effective catalysts that will enable this reaction to be carried out under mild conditions with high efficiency and selectivity. Recently, deep eutectic solvents (DES) have become the subject of interest as potential effective, cheap, and biodegradable catalysts for this process. The work presents an up-to-date overview of the method of cyclic carbonate synthesis from CO₂ and epoxides with the use of DES as catalysts.

Silica-Based Supported Ionic Liquid-like Phases as Heterogeneous Catalysts

Supported ionic liquid phases offer several advantages related with catalysis. Immobilization of ionic liquid on the solid support provides catalytic activity or efficient matrix for active phases, as enzymes or metal compounds. Ionic liquid can be physically adsorbed on the carrier (supported ionic liquid phase) or chemically grafted to the material surface (supported ionic liquid-like phase). The use of supported ionic liquid phases improves mass transport, reduces ionic amount in the process and, most importantly, enables effortless catalyst separation and recycling. Moreover, chemical modification of the surface material with ionic liquid prevents its leaching, enhancing length of catalyst life. Silica-based materials have become an effective and powerful matrix for supported ionic liquid-like phase due to its cost-efficiency, presence of hydroxyl groups on the surface enabling its functionalization, and specific material properties, such as the size and shapes of the pores. For these reasons, supported ionic liquid-like phase silica-based materials are successfully used in the organic catalysis.

Hypercrosslinked Ionic Polymers with High Ionic Content for Efficient Conversion of Carbon Dioxide into Cyclic Carbonates

The effective conversion of carbon dioxide (CO2) into cyclic carbonates requires porous materials with high ionic content and large specific surface area. Herein, we developed a new systematic post-synthetic modification strategy for synthesizing imidazolium-based hypercrosslinked ionic polymers (HIPs) with high ionic content (up to 2.1 mmol g−1) and large specific surface area (385 m2 g−1) from porous hypercrosslinked polymers (HCPs) through addition reaction and quaternization. The obtained HIPs were efficient in CO2 capture and conversion. Under the synergistic effect of high ionic content, large specific surface area, and plentiful micro/mesoporosity, the metal-free catalyst [HCP-CH2-Im][Cl]-1 exhibited quantitative selectivities, high catalytic yields, and good substrate compatibility for the conversion of CO2 into cyclic carbonates at atmospheric pressure (0.1 MPa) in a shorter reaction time in the absence of cocatalysts, solvents, and additives. High catalytic yields (styrene oxide, 120 °C, 8 h, 94% yield; 100 °C, 20 h, 93% yield) can be achieved by appropriately extending the reaction times at low temperature, and the reaction times are shorter than other porous materials under the same conditions. This work provides a new strategy for synthesizing an efficient metal-free heterogeneous catalyst with high ionic content and a large specific surface area from HCPs for the conversion of CO2 into cyclic carbonates. It also demonstrates that the ionic content and specific surface area must be coordinated to obtain high catalytic activity for CO2 cycloaddition reaction.

Mixed Manganese Dioxide on Magnetite Core MnO2@Fe3O4 as a Filler in a High-Performance Magnetic Alginate Membrane

The process of ethanol dehydration via pervaporation was performed using alginate membranes filled with manganese dioxide and a mixed filler consisting of manganese dioxide on magnetite core MnO₂@Fe₃O₄ particles. The crystallization of manganese dioxide on magnetite nanoparticle surface resulted in a better dispersibility of this mixed filler in polymer matrix, with the preservation of the magnetic properties of magnetite. The prepared membranes were characterized by contact angle, degree of swelling and SEM microscopy measurements and correlated with their effectiveness in the pervaporative dehydration of ethanol. The results show a strong relation between filler properties and separation efficiency. The membranes filled with the mixed filler outperformed the membranes containing only neat oxide, exhibiting both higher flux and separation factor. The performance changed depending on filler content; thus, the presence of optimum filler loading was observed for the studied membranes. The best results were obtained for the alginate membrane filled with 7 wt.% of mixed filler MnO₂@Fe₃O₄ particles. For this membrane, the separation factor and flux equalled to 483 and 1.22 kg·m⁻²·h⁻¹, respectively.

Butyl-Methyl-Pyridinium Tetrafluoroborate Confined in Mesoporous Silica Xerogels: Thermal Behaviour and Matrix-Template Interaction

Organic-inorganic silica composites have been prepared via acid catalyzed sol-gel route using tetramethoxysilan (TMOS) and methyl-trimethoxysilane (MTMS) as silica precursors and n-butyl-3-methylpyridinium tetrafluoroborate ([bmPy][BF₄]) as co-solvent and pore template, by varying the content of the ionic liquid (IL). Morphology of the xerogels prepared using the ionic liquid templating agent were investigated using scanning electron microscopy and small angle neutron scattering (SANS). Thermal analysis has been used in order to evaluate the thermal and structural stability of the materials, in both nitrogen and synthetic air atmosphere. In nitrogen atmosphere, the IL decomposition took place in one step starting above 150 °C and completed in the 150–460 °C temperature interval. In synthetic air atmosphere, the IL decomposition produced two-step mass loss, mainly in the 170–430 °C temperature interval. The decomposition mechanism of the IL inside the silica matrix was studied by mass spectrometric evolved gas analysis (MSEGA). The measurements showed that the degradation of the IL’s longer side chain (butyl) starts at low temperature (above 150 °C) through a C-N bond cleavage, initiated by the nucleophilic attack of a fluorine ion.