Nano-PAA-CuCl2 Composite as Fenton-Like Reusable Catalyst to Enhanced Degrade Organic Pollutant MB/MO

Modulating Cu valence state in Cu and graphene oxide composites for electrocatalytic tetracycline hydrochloride degradation

Cu and graphene oxide composites (Cu-GO) were designed by anchoring Cu+ via oxygen groups in GO based on the heavy co-relationships of copper (Cu) anode electrocatalytic activity with Cu valence state. With the consumption of oxygen groups under various pyrolysis temperatures, the Cu valence state changed from Cu ions (as CuCl2 and CuCl) to Cu oxide (CuO and Cu2O) and the final metallic Cu. In which the Cu+ in CuCl was more favorable for electrocatalytic oxidation than other Cu valence states. Due to the dramatic contribution of 1O2 and active chlorine, 100% degradation efficiency was achieved using tetracycline hydrochloride (TCH) as the target pollutant. Cu+ showed a selective preference for 1O2 and active chlorine triggering, rather than metallic Cu. Under the attack of 1O2 and active chlorine, the degradation intermediates of TCH were then provided by LC-MS results. The final results not only prove the feasibility of the Cu-GO/electrocatalysis system for pollution control but also shed light on the anode design via Cu valence state modulation.

Degradation of Diclofenac by Loaded Solid Superbase-Activated Persulfate

Alkali-activated persulfate (PS) is widely used in situ in chemical oxidation processes; however, studies on the innovation of the alkali activation process are very limited. Two supported solid superbases, namely KNO3/γ-Al2O3 (KAl) and KNO3/SBA-15/MgO (KSM), respectively, were prepared and used to activate persulfate to degrade DCF in this work. The results showed that the superbases elevated the solution pH once added and thus could catalyze persulfate to degrade diclofenac efficiently above pH 10.5. The catalytic efficiency of KAl was close to that of sodium hydroxide, and that of KSM was the highest. The mechanism might be that, in addition to raising the solution pH, some potassium existed as K2O2, which had a strong oxidizing effect and was conducive to DCF removal. Hydroxyl, sulfate and superoxide radicals were all found in the reaction system, among which hydroxyl might play the most important role. The material composition ratio, common anion and humic acid all had some influences on the catalytic efficiency. A total of five intermediates were found in the KSM/PS oxidation system, and six oxidation pathways, which were hydroxylation, dehydrogen, dechlorination, dehydration, decarboxylation, and C-N bond breakage, might be involved in the reaction process. Several highly toxic oxidation products that should be paid attention to were also proposed.

Copper Recovery from Industrial Bimetallic Composite Ionic Liquids by Direct Electrodeposition and the Effect of Temperature and Ultrasound

Critical processing protocols of industrial bimetallic composite ionic liquid (IL) are necessary to assure good mass transfer rates for process optimization and efficient metal recovery. Here, the effects of different conditions on the electrochemical behavior and copper recovery from the industrial bimetallic composite IL are crucial for effective resource utilization. Cyclic voltammetry (CV) shows that the reduction of Cu(I) to Cu(0) during the cathodic reduction region is the irreversible diffusion-controlled process, and the diffusion coefficient increased with temperature which indicated that increasing temperature could promote the diffusion and mass transfer. During electrodeposition, metallic copper is obtained exclusively on the cathode, while CuCl₂ accumulates exclusively on the anode. Scanning electron microscopy shows that the micron-size electrodeposits become larger and significantly rougher with increasing temperature and ultrasonic frequency, illustrating that these factors hasten the nucleation and crystallization rates at high overpotentials. The efficiency of copper recovery is greatly improved by employing high temperature and ultrasonic cavitation, and the highest values correspond to r = 76.9% at 80 °C and r = 63.6% at 40 kHz. The study lays the foundation for efficient and rapid recovery of copper from spent ILs.

A Keggin-type polyoxomolybdate-based crystalline material formed by hydrothermal transformation: photo/electro-catalytic properties and mechanism study

This study constructs a POM-based crystalline material of [(SiMo12O40)Cu6(2,2′-bipy)6(Mo6O22)] (1). The photocatalytic MB degradation and electrocatalytic nitrite reduction properties of complex 1 are systematically studied for the first time.