Improving the Performance of Gd Addition on Catalytic Activity and SO2 Resistance over MnOx/ZSM-5 Catalysts for Low-Temperature NH3-SCR

Enhancing Water Tolerance and N2 Selectivity in NH3-SCR Catalysts by Protecting Mn Oxide Nanoparticles in a Silicalite-1 Layer

Mn-based catalysts are promising candidates for eliminating harmful nitrogen oxides (NOx) via selective catalytic reduction with ammonia (NH3-SCR) due to their inherent strong redox abilities. However, poor water tolerance and low N2 selectivity are still the main limitations for practical applications. Herein, we succeeded in preparing an active catalyst for NH3-SCR with improved water tolerance and N2 selectivity based on protecting MnOx with a secondary growth of a hydrophobic silicalite-1. This protection suppressed catalyst deactivation by water adsorption. Interestingly, impregnating MnOx on MesoTS-1 followed by silicalite-1 protection allowed for a higher dispersion of MnOx species, thus increasing the concentration of acid sites. Consequently, the level of N2O formation is decreased. These improvements resulted in a broader operating temperature of NOx conversion and a modification of the NH3-SCR mechanism. Diffuse reflectance infrared Fourier transform spectroscopy analysis revealed that unprotected Mn/MesoTS-1 mainly followed the Eley-Rideal mechanism, while Mn/MesoTS-1@S1 followed both Langmuir-Hinshelwood and Eley-Rideal mechanisms.

Remove elemental mercury from simulated flue gas by CeO2-modified MnOx/HZSM-5 adsorbent

In this study, we synthesized a Ce-modified Mn/HZSM-5 adsorbent via the ultrasound-assisted impregnation for Hg0 capture. Given the addition of 15% CeO2, ~ 100% Hg0 efficiency was reached at 200 °C, suggesting its promotional effect on Hg0 removal. The doped Ce introduced additional chemisorbed oxygen species onto the adsorbent surfaces, which facilitated the oxidation of Hg0 to HgO. Even though adding CeO2 led to a weakened adsorbent acidity, yet it appeared that this negative affect could be completely overcome by the enhanced oxidative ability, which finally endowed Ce-modified Mn/HZSM-5 with a satisfactory Hg0 removal performance within the whole investigated temperature range. During the Hg0 capture process, chemisorption was predominant with Mn4+operating as the main active site for oxidizing Hg0 to Hg2+. Finally, the 15Ce-Mn/HZSM-5 adsorbent exhibited good recyclability and stability. However, its tolerance to H2O and SO2 appeared relatively weak, suggesting that some modification should be conducted to improve its practicality.

Elucidating the facet-dependent reactivity of CrMn catalyst for selective catalytic reduction of NOx with NH3

The facet-dependent reactivity of CrMn catalysts was still unclear, hindering the further enhancement of their low-temperature SCR performance. Herein, the facet-dependent reactivity of CrMn_1.5O₄ catalyst for NH₃-SCR of NO_x was innovatively illustrated by numerous characterizations and density functional theory (DFT) calculations. Exposed (100) facet of CrMn_1.5O₄ catalyst exhibited best low-temperature SCR activity with ≥90 % NO conversion within 148-296 °C and 2.86 × 10^-3 mol/(g·s) reaction rate within 160-240 °C. The characterizations revealed that (100) facet could induce the increase of BET specific area, electron transfer, concentration of Mn⁴⁺ and O_α, surface acidity, redox ability, NH₃ and NO_x adsorption/activation capacity. Subsequently, DFT calculations demonstrated that (100) facet exhibited the strongest affinity for NH₃ and NO due to its unique 3O_3c-Mn_5c-2O_4c bond and abundant charges transfer near the active adsorption sites, and Brønsted acid and oxygen vacancies were most easily formed on (100) facet. Furthermore, H₂O formation as the rate determining step easily occurred on (100) facet. Eventually, we successfully improved the low-temperature SCR activity of CrMn_1.5O₄ catalyst by further tailoring highly active (100) facet from 0.754 to 0.865. This work provides the deeper understanding of facet-dependent reactivity and a good strategy to improve the catalytic activity of the catalysts.

Study of the denitration performance of a ceramic filter using a manganese-based catalyst

A MnO _x /γ-Al₂O₃ catalyst was prepared by impregnation of manganese acetate and alumina. After optimizing the composition, it was loaded into a ceramic filter (CF) by a one-step coating method. The results show that MnO _x /γ-Al₂O₃ had the best denitration activity when the Mn loading was 4 wt% with a calcination temperature of 400 °C. The MnO _x /γ-Al₂O₃ catalyst ceramic filter (MA-CCF) was made by loading the CF twice with MnO _x /γ-Al₂O₃. When face velocity (FV) was 1 m min^-1, MA-CCF displayed more than 80% NO conversion at 125-375 °C and possessed a good resistance of H₂O and SO₂. The abundant surface adsorbed oxygen, dense membrane and high-density fiber structure on the outer layer of CF effectively protected the catalyst and could improve MA-CCF denitration activity. The multiple advantages of MA-CCF made it possible for good application prospects.

Recent Breakthroughs and Advancements in NOx and SOx Reduction Using Nanomaterials-Based Technologies: A State-of-the-Art Review

Nitrogen and sulpher oxides (NO_x, SO_x) have become a global issue in recent years due to the fastest industrialization and urbanization. Numerous techniques are used to treat the harmful exhaust emissions, including dry, traditional wet and hybrid wet-scrubbing techniques. However, several difficulties, including high-energy requirement, limited scrubbing-liquid regeneration, formation of secondary pollutants and low efficiency, limit their industrial utilization. Regardless, the hybrid wet-scrubbing technology is gaining popularity due to low-costs, less-energy consumption and high-efficiency removal of air pollutants. The removal/reduction of NO_x and SO_x from the atmosphere has been the subject of several reviews in recent years. The goal of this review article is to help scientists grasp the fundamental ideas and requirements before using it commercially. This review paper emphasizes the use of green and electron-rich donors, new breakthroughs, reducing GHG emissions, and improved NO_x and SO_x removal catalytic systems, including selective/non-catalytic reduction (SCR/SNCR) and other techniques (functionalization by magnetic nanoparticles; NP, etc.,). It also explains that various wet-scrubbing techniques, synthesis of solid iron-oxide such as magnetic (Fe₃O₄) NP are receiving more interest from researchers due to the wide range of its application in numerous fields. In addition, EDTA coating on Fe₃O₄ NP is widely used due to its high stability over a wide pH range and solid catalytic systems. As a result, the Fe₃O₄@EDTA-Fe catalyst is projected to be an optimal catalyst in terms of stability, synergistic efficiency, and reusability. Finally, this review paper discusses the current of a heterogeneous catalytic system for environmental remedies and sustainable approaches.

FeVO4-supported Mn–Ce oxides for the low-temperature selective catalytic reduction of NOx by NH3

Iron vanadate (FeVO4) nanorods are used as a carrier to support manganese (Mn) and cerium (Ce) oxides for the selective catalytic reduction (SCR) of nitrogen oxides (NOx) with NH3 for the first time.