Formic Acid Dehydrogenation Using Noble-Metal Nanoheterogeneous Catalysts: Towards Sustainable Hydrogen-Based Energy

Efficient Atomically Dispersed Co/N-C Catalysts for Formic Acid Dehydrogenation and Transfer Hydrodeoxygenation of Vanillin

Atomically dispersed catalysts have gained considerable attention due to their unique properties and high efficiency in various catalytic reactions. Herein, a series of Co/N-doped carbon (N-C) catalysts was prepared using a metal-lignin coordination strategy and employed in formic acid dehydrogenation (FAD) and hydrodeoxygenation (HDO) of vanillin. The atomically dispersed Co/N-C catalysts showed outstanding activity, acid resistance, and long-term stability in FAD. The improved activity and stability may be attributed to the high dispersion of Co species, increased surface area, and strong Co-N interactions. XPS and XAS characterization revealed the formation of Co-N3 centers, which are assumed to be the active sites. In addition, DFT calculations demonstrated that the adsorption of formic acid on single-atom Co was stronger than that on Co13 clusters, which may explain the high catalytic activity. The Co/N-C catalyst also showed promising performance in the transfer HDO of vanillin with formic acid, without any external additional molecular H2.

Ultrasmall Pd nanoparticles supported on a metal-organic framework DUT-67-PZDC for enhanced formic acid dehydrogenation

The highly dispersed ultrasmall palladium nanoparticles (Pd NPs) (1.7 nm) were successfully immobilized on a N-containing metal-organic framework (MOF, DUT-67-PZDC) using a co-reduction method, and it is used as an excellent catalyst for formic acid dehydrogenation (FAD). The optimized catalyst Pd/DUT-67-PZDC(10, 10 wt% Pd loading) shows 100% hydrogen (H2) selectivity and formic acid (FA) conversion at 60 °C, and the commendable initial turnover frequency (TOF) values of 2572 h-1 with the sodium formate (SF) as an additive and 1059 h-1 even without SF, which is better than most reported MOF supported Pd monometallic heterogeneous catalysts. The activation energy (Ea) of FAD is 43.2 KJ/mol, which is lower than most heterogeneous catalysts. In addition, the optimized catalyst Pd/DUT-67-PZDC(10) maintained good stability over five consecutive runs, demonstrating only minimal decline in catalytic activity. The outstanding catalytic performance could be ascribed to the synergistic corporations of the unique structure of DUT-67-PZDC carrier with hierarchical pore characteristic, the metal-support interaction (MSI) between the active Pd NPs and DUT-67-PZDC, the highly dispersed Pd NPs with ultrafine size serve as the catalytic active site, as well as the N sites on the support could act as the proton buffers. This work provides a new paradigm for the efficient H2 production of FAD by constructing highly active heterogeneous Pd-based catalysts using MOF supports.

Recent Advances in Reversible Liquid Organic Hydrogen Carrier Systems: From Hydrogen Carriers to Catalysts

Liquid organic hydrogen carriers (LOHCs) have gained significant attention for large-scale hydrogen storage due to their remarkable gravimetric hydrogen storage capacity (HSC) and compatibility with existing oil and gas transportation networks for long-distance transport. However, the practical application of reversible LOHC systems has been constrained by the intrinsic thermodynamic properties of hydrogen carriers and the performances of associated catalysts in the (de)hydrogenation cycles. To overcome these challenges, thermodynamically favored carriers, high-performance catalysts, and catalytic procedures need to be developed. Here, significant advances in recent years have been summarized, primarily centered on regular LOHC systems catalyzed by homogeneous and heterogeneous catalysts, including dehydrogenative aromatization of cycloalkanes to arenes and N-heterocyclics to N-heteroarenes, as well as reverse hydrogenation processes. Furthermore, with the development of metal complexes for dehydrogenative coupling, a new family of reversible LOHC systems based on alcohols is described that can release H2 under relatively mild conditions. Finally, views on the next steps and challenges in the field of LOHC technology are provided, emphasizing new resources for low-cost hydrogen carriers, high-performance catalysts, catalytic technologies, and application scenarios.

2D Metal/Graphene and 2D Metal/Graphene/Metal Systems for Electrocatalytic Conversion of CO2 to Formic Acid

Efficiently transforming CO2 into renewable energy sources is crucial for decarbonization efforts. Formic acid (HCOOH) holds great promise as a hydrogen storage compound due to its high hydrogen density, non-toxicity, and stability under ambient conditions. However, the electrochemical reduction of CO2 (CO2 RR) on conventional carbon black-supported metal catalysts faces challenges such as low stability through dissolution and agglomeration, as well as suffering from high overpotentials and the necessity to overcome the competitive hydrogen evolution reaction (HER). In this study, we modify the physical/chemical properties of metal surfaces by depositing metal monolayers on graphene (M/G) to create highly active and stable electrocatalysts. Strong covalent bonding between graphene and metal is induced by the hybridization of sp and d orbitals, especially the sharpd z 2 ${{d}_{{z}^{2}}}$ ,d y z ${{d}_{yz}}$ , andd x z ${{d}_{xz}}$ orbitals of metals near the Fermi level, playing a decisive role. Moreover, charge polarization on graphene in M/G enables the deposition of another thin metallic film, forming metal/graphene/metal (M/G/M) structures. Finally, evaluating overpotentials required for CO2 reduction to HCOOH, CO, and HER, we find that Pd/G, Pt/G/Ag, and Pt/G/Au exhibit excellent activity and selectivity toward HCOOH production. Our novel 2D hybrid catalyst design methodology may offer insights into enhanced electrochemical reactions through the electronic mixing of metal and other p-block elements.

Stearic Acid as an Atomic Layer Deposition Inhibitor: Spectroscopic Insights from AFM-IR

Modern-day chip manufacturing requires precision in placing chip materials on complex and patterned structures. Area-selective atomic layer deposition (AS-ALD) is a self-aligned manufacturing technique with high precision and control, which offers cost effectiveness compared to the traditional patterning techniques. Self-assembled monolayers (SAMs) have been explored as an avenue for realizing AS-ALD, wherein surface-active sites are modified in a specific pattern via SAMs that are inert to metal deposition, enabling ALD nucleation on the substrate selectively. However, key limitations have limited the potential of AS-ALD as a patterning method. The choice of molecules for ALD blocking SAMs is sparse; furthermore, deficiency in the proper understanding of the SAM chemistry and its changes upon metal layer deposition further adds to the challenges. In this work, we have addressed the above challenges by using nanoscale infrared spectroscopy to investigate the potential of stearic acid (SA) as an ALD inhibiting SAM. We show that SA monolayers on Co and Cu substrates can inhibit ZnO ALD growth on par with other commonly used SAMs, which demonstrates its viability towards AS-ALD. We complement these measurements with AFM-IR, which is a surface-sensitive spatially resolved technique, to obtain spectral insights into the ALD-treated SAMs. The significant insight obtained from AFM-IR is that SA SAMs do not desorb or degrade with ALD, but rather undergo a change in substrate coordination modes, which can affect ALD growth on substrates.

Recovery of fuel from real waste oily sludge via a new eco-friendly surfactant material used in a digital baffle batch extraction unit

This study focused on developing a new cocktail extraction agent (CEA) composed of solvent and a new surfactant material (SM) for enhancing the efficiency of fuel recovery from real waste oil sludge (WSO). The effects of different solvents (e.g. methyl ethyl ketone (MEK), naphtha, petrol and kerosene), SMs (Dowfax and sodium thiosulfate), extraction time (10-20 min), extraction temperatures (20-60 °C) and CEA/sludge ratios (1-4) on the extraction performance were investigated. SMs and DBBE design enhanced the extraction efficiency by increasing the dispersion of solvent in WSO and enhancing the mixing and mass transfer rates. Results proved that Dowfax was the best SM for oil recovery under various conditions. The best CEA (e.g. MEK and Dowfax) provides the maximum fuel recovery rate of 97% at a period of 20 min, temperature of 60 °C and 4:1 CEA/sludge ratio. The produced fuel was analysed and fed to the distillation process to produce diesel oil. The characteristics of diesel oil were measured, and findings showed that it needs treatment processes prior its use as a finished fuel.

Applying MCM-48 mesoporous material, equilibrium, isotherm, and mechanism for the effective adsorption of 4-nitroaniline from wastewater

In this work, the MCM-48 mesoporous material was prepared and characterized to apply it as an active adsorbent for the adsorption of 4-nitroaniline (4-Nitrobenzenamine) from wastewater. The MCM-48 characterizations were specified by implementing various techniques such as; scanning electron microscopy (SEM), Energy dispersive X-ray analysis (EDAX), X-ray diffraction (XRD), Brunauer-Emmett-Teller (BET) surface area, pore size distribution (PSD), and Fourier transform infrared (FTIR). The batch adsorption results showed that the MCM-48 was very active for the 4-nitroaniline adsorption from wastewater. The adsorption equilibrium results were analyzed by applying isotherms like Langmuir, Freundlich, and Temkin. The maximum experimental uptake according to type I Langmuir adsorption was found to be 90 mg g^-1 approximately. The Langmuir model with determination coefficient R² = 0.9965 is superior than the Freundlich model R² = 0.99628 and Temkin model R² = 0.9834. The kinetic adsorption was investigated according to pseudo 1st order, pseudo 2nd order, and Intraparticle diffusion model. The kinetic results demonstrated that the regression coefficients are so high R² = 0.9949, that mean the pseudo 2nd order hypothesis for the adsorption mechanism process appears to be well-supported. The findings of adsorption isotherms and kinetics studies indicate the adsorption mechanism is a chemisorption and physical adsorption process.

Efficient [Fe-Imidazole@SiO2] Nanohybrids for Catalytic H2 Production from Formic Acid

Three imidazole-based hybrid materials, coded as IGOPS, IPS and impyridine@SiO₂ nanohybrids, were prepared via the covalent immobilization of N-ligands onto a mesoporous nano-SiO₂ matrix for H₂ generation from formic acid (FA). BET and HRTEM demonstrated that the immobilization of the imidazole derivative onto SiO₂ has a significant effect on the SSA, average pore volume, and particle size distribution. In the context of FA dehydrogenation, their catalytic activity (TONs, TOFs), stability, and reusability were assessed. Additionally, the homologous homogeneous counterparts were evaluated for comparison purposes. Mapping the redox potential of solution E_h vs. SHE revealed that poly-phosphine PP₃ plays an essential role in FA dehydrogenation. On the basis of performance and stability, [Fe²⁺/IGOPS/PP₃] demonstrated superior activity compared to other heterogeneous catalysts, producing 9.82 L of gases (VH₂ + CO₂) with TONs = 31,778, albeit with low recyclability. In contrast, [Fe²⁺/IPS/PP₃] showed the highest stability, retaining considerable performance after three consecutive uses. With VH₂ + CO₂ = 7.8 L, [Fe²⁺/impyridine@SiO₂/PP₃] activity decreased, and it was no longer recyclable. However, the homogeneous equivalent of [Fe²⁺/impyridine/PP₃] was completely inactive. Raman, FT/IR, and UV/Vis spectroscopy demonstrated that the reduced recyclability of [Fe²⁺/IGOPS/PP₃] and [Fe²⁺/impyridine@SiO₂/PP₃] nanohybrids is due to the reductive cleavage of their C-O-C bonds during catalysis. An alternative grafting procedure is proposed, applying here to the grafting of IPS, resulting in its higher stability. The accumulation of water derived from substrate's feeding causes the inhibition of catalysis. In the case of [Fe²⁺-imidazole@SiO₂] nanohybrids, simple washing and drying result in their re-activation, overcoming the water inhibition. Thus, the low-cost imidazole-based nanohybrids IGOPS and IPS are capable of forming [Fe²⁺/IGOPS/PP₃] and [Fe²⁺/IPS/PP₃] heterogeneous catalytic systems with high stability and performance for FA dehydrogenation.

In vitro anticancer and antibacterial performance of biosynthesized Ag and Ce co-doped ZnO NPs

The great potential of zinc oxide nanoparticles (ZnO NPs) for biomedical applications is attributed to their physicochemical properties. In this work, pure and Ag and Ce dual-doped ZnO NPs were synthesized through a facile and green route to examine their cytotoxicity in breast cancer and normal cells. The initial preparation of dual-doped nanoparticles was completed by the usage of taranjabin. The synthesis of Ag and Ce dual-doped ZnO NPs was started with preparing the Ce:Ag ratios of 1:1, 1:2, and 1:4. The cytotoxicity effects of synthesized nanoparticles against breast normal cells (MCF-10A) and breast cancer cells (MDA-MB-231) were examined. The hexagonal structure of synthesized nanoparticles was observed through the results of X-ray diffraction (XRD). Scanning electron microscopy (SEM) images exhibited the spherical shape and smooth surfaces of prepared particles along with the homogeneous distribution of Ag and Ce in ZnO with high-quality lattice fringes without any distortions. According to the cytotoxic results, the effects of Ag/Ce dual-doped ZnO NPs on breast cancer (MDA-MB-231) cells were significantly more than of pure ZnO NPs, while dual-doped and pure nanoparticles remained indifferent towards breast normal (MCF-10A) cells. In addition, we investigated the antimicrobial activity against harmful bacteria.

Synthesis characterization of Zn-based MOF and their application in degradation of water contaminants

Metal-organic frameworks (MOFs) are currently popular porous materials with research and application value in various fields such as medicine and engineering. Aiming at the application of MOFs in photocatalysis, this paper mainly reviews the main synthesis methods of ZnMOFs and the latest research progress of Zn MOF-based photocatalysts to degrade organic pollutants in water, such as organic dyes. This nanomaterial is being used to treat wastewater and has proven to be very efficient because of its exceptionally large surface area and porous nature. The results show that Zn-MOFs are capable of high degradation of the above pollutants and over 90% of degradation was observed in publications. In addition, the reusability percentage was examined and studies showed that the Zn-MOF nanostructure has very good stability and can continue to degrade a high percentage of pollutants after several cycles. This review focuses on Zn-MOFs and their composites. First, the methods of synthesis and characterization of these compounds are given. Finally, the application of these composites in the process of photocatalytic degradation of dye pollutants such as methylene blue, methyl orange, crystal violet, rhodamine B, etc. is explained.

An intelligent DNA nanorobot for detection of MiRNAs cancer biomarkers using molecular programming to fabricate a logic-responsive hybrid nanostructure

Herein, we designed a DNA framework-based intelligent nanorobot using toehold-mediated strand displacement reaction-based molecular programming and logic gate operation for the selective and synchronous detection of miR21 and miR125b, which are known as significant cancer biomarkers. Moreover, to investigate the applicability of our design, DNA nanorobots were implemented as capping agents onto the pores of MSNs. These agents can develop a logic-responsive hybrid nanostructure capable of specific drug release in the presence of both targets. The prosperous synthesis steps were verified by FTIR, XRD, BET, UV-visible, FESEM-EDX mapping, and HRTEM analyses. Finally, the proper release of the drug in the presence of both target microRNAs was studied. This Hybrid DNA Nanostructure was designed with the possibility to respond to any target oligonucleotides with 22 nucleotides length.

Production of H2-Free Carbon Monoxide from Formic Acid Dehydration: The Catalytic Role of Acid Sites in Sulfated Zirconia

The formic acid (CH₂O₂) decomposition over sulfated zirconia (SZ) catalysts prepared under different synthesis conditions, such as calcination temperature (500-650 °C) and sulfate loading (0-20 wt.%), was investigated. Three sulfate species (tridentate, bridging bidentate, and pyrosulfate) on the SZ catalysts were characterized by using temperature-programmed decomposition (TPDE), Fourier-transform infrared spectroscopy (FTIR), and X-ray photoelectron spectroscopy (XPS). The acidic properties of the SZ catalysts were investigated by the temperature-programmed desorption of iso-propanol (IPA-TPD) and pyridine-adsorbed infrared (Py-IR) spectroscopy and correlated with their catalytic properties in formic acid decomposition. The relative contributions of Brønsted and Lewis acid sites to the formic acid dehydration were compared, and optimal synthetic conditions, such as calcination temperature and sulfate loading, were proposed.

Biosynthesis of silver nanoparticles using Lawsonia inermis and their biomedical application

Developing biosynthesis of silver nanoparticles (Ag‐NPs) using plant extract is an environmentally friendly method to reduce the use of harmful chemical substances. The green synthesis of Ag‐NPs by Lawsonia inermis extract and its cellular toxicity and the antimicrobial effect was studied. The physical and chemical properties of synthesised Ag‐NPs were investigated using UV‐visible spectroscopy, infrared spectroscopy, X‐ray diffraction (XRD), scanning, and transmission electron microscopy. The average size of Ag‐NPs was 40 nm. The XRD result shows peaks at 2θ = 38.07°, 44.26°, 64.43°, and 77.35° are related to the FCC structure of Ag‐NPs. Cytotoxicity of synthesised nanoparticles was evaluated by MTT toxicity test on breast cancer MCF7 cell line. Observations showed that the effect of cytotoxicity of nanoparticles on the studied cell line depended on concentration and time. The obtained IC₅₀ was considered for cells at a dose of 250 μg/ml. Growth and survival rates decreased exponentially with the dose. Antimicrobial properties of Ag‐NPs synthesised with extract were investigated against Escherichia coli, Salmonella typhimurium, Bacillus cereus, and Staphylococcus aureus to calculate the minimum inhibitory concentration and the minimum bactericidal concentration of (MBC). The results showed that the synthesised Ag‐NPs and the plant extract have antimicrobial properties. The lowest concentration of Ag‐NPs that can inhibit the growth of bacterial strains was 25 μg/ml.

Plant-mediated synthesis of silver-doped zinc oxide nanoparticles and evaluation of their antimicrobial activity against bacteria cause tooth decay

In this research, silver-doped zinc oxide (SdZnO) nanoparticles (NPs) were synthesized in an environmental-friendly manner. The synthesized NPs were identified by UV-vis spectroscopy, X-ray diffraction (XRD), and scanning electron microscopy (SEM). Finally, the antimicrobial activity of synthesized ZnO and SdZnO NPs was performed. It was observed that by doping silver, the size of ZnO NPs was changed. By adding silver to ZnO NPs, the antimicrobial effect of ZnO NPs was improved. Antibacterial test against gram-positive bacterium Streptococcus mutants showed that SdZnO NPs with a low density of silver had higher antibacterial activity than ZnO NPs; Therefore, SdZnO NPs can be used as a new antibacterial agent in medical applications.

Facile synthesis of Cu NPs@Fe3O4-lignosulfonate: Study of catalytic and antibacterial/antioxidant activities

Environmental pollution is one of the important concerns for human health. There are different types of pollutants and techniques to eliminate them from the environment. We hereby report an efficient method for the remediation of environmental contaminants through the catalytic reduction of the selected pollutants. A green method has been developed for the immobilization of copper nanoparticles on magnetic lignosulfonate (Cu NPs@Fe₃O₄-LS) using the aqueous extract of Filago arvensis L. as a non-toxic reducing and stabilizing agent. The characterization of the prepared Cu NPs@Fe₃O₄-LS was achieved by vibrating sample magnetometer (VSM), Fourier-transform infrared spectroscopy (FT-IR), transmission electron microscopy (TEM), high resolution TEM (HRTEM), X-ray diffraction (XRD), scanning TEM (STEM), thermogravimetry-differential thermal analysis (TG/DTA), fast Fourier transform (FFT), energy-dispersive X-ray spectroscopy (EDS), and X-ray photoelectron (XPS) analyses. The synthesized Cu NPs@Fe₃O₄-LS was applied as a magnetic and green catalyst in the reduction of Congo Red (CR), 4-nitrophenol (4-NP), and methylene blue (MB). The progress of the reduction reactions was monitored by UV-Vis spectroscopy. Finally, the biological properties of the Cu NPs@Fe₃O₄-LS were investigated. The prepared catalyst demonstrated excellent catalytic efficiency in the reduction of CR, 4-NP, and MB in the presence of sodium borohydride (NaBH₄) as the reducing agent. The appropriate magnetism of Cu NPs@Fe₃O₄-LS made its recovery very simple. The advantages of this process include a simple reaction set-up, high and catalytic antibacterial/antioxidant activities, short reaction time, environmentally friendliness, high stability, and easy separation of the catalyst. In addition, the prepared Cu NPs@Fe₃O₄-LS could be reused for four cycles with no significant decline in performance.