Effect of UV Irradiation on the Structural Variation of Metal Oxide-Silica Nanocomposites for Enhanced Removal of Erythromycin at Neutral pH

Performance of magnetic nanocomposite based on xanthan gum-grafted-poly(acrylamide) crosslinked by borax for the effective elimination of amoxicillin from aquatic environments

This study evaluated the effectiveness of using nanocomposite (NCs) of xanthan gum grafted polyacrylamide crosslinked Borax - iron oxide nanoparticle (XG-g-pAAm-CL-Borax-IONP) to remove the amoxicillin antibiotic (AMX) from an aquatic environment. To confirm the structural characteristics of the prepared XG-g-pAAm-CL-Borax-IONP NCs, unique characterization methods (XRD, FT-IR, FE-SEM, EDX, BET, TGA, Zeta, and VSM) were used. Adsorption experimental setups were performed with the influence of solution pH (4-9), the effect of adsorbent dose (0.003-0.02 g), the effect of contact time (5-45 min), and the effect of initial AMX concentration (50-400 mg/L) to achieve the most efficient adsorption conditions. Based on the Freundlich isotherm model, XG-g-pAAm-CL-Borax-IONP NCs provided the maximum AMX adsorption capacity of 1183.639 mg/g. This research on adsorption kinetics also established that the pseudo-second-order model (R2 = 0.991) is outstanding compatibility with the experimental results. AMX adsorption on the NCs may occur through intermolecular hydrogen bonding, diffusion, and trapping into the polymer network. Even after five cycles, these NCs still displayed the best performance. Based on these results, XG-g-pAAm-CL-Borax-IONP NCs may be a viable material for the purification of AMX from contaminated water.

Lethal puncturing of planktonic Gram-positive and Gram-negative bacteria by magnetically-rotated silica hexapods

Planktonic bacterial presence in many industrial and environmental applications and personal health-care products is generally countered using antimicrobials. However, antimicrobial chemicals present an environmental threat, while emerging resistance reduces their efficacy. Suspended bacteria have no defense against mechanical attack. Therefore, we synthesized silica hexapods on an α-Fe2O3 core that can be magnetically-rotated to inflict lethal cell-wall-damage to planktonic Gram-negative and Gram-positive bacteria. Hexapods possessed 600 nm long nano-spikes, composed of SiO2, as shown by FTIR and XPS. Fluorescence staining revealed cell wall damage caused by rotating hexapods. This damage was accompanied by DNA/protein release and bacterial death that increased with increasing rotational frequency up to 500 rpm. Lethal puncturing was more extensive on Gram-negative bacteria than on Gram-positive bacteria, which have a thicker peptidoglycan layer with a higher Young's modulus. Simulations confirmed that cell-wall-puncturing occurs at lower nano-spike penetration levels in the cell walls of Gram-negative bacteria. This approach offers a new way to kill bacteria in suspension, not based on antimicrobial chemicals.

Effect of copper doping on the photocatalytic performance of Ni2O3@PC membrane composites in norfloxacin degradation

In this study, copper (Cu) and nickel oxide (Ni2O3) microtubes (MTs) were synthesized using an electroless template deposition technique within porous polycarbonate (PC) track-etched membranes (TeMs) to obtain Cu@PC and Ni2O3@PC composite membranes, respectively. The pristine PC TeMs featured nanochannels with a pore density of 4 × 107 pores per cm2 and an average pore diameter of 400 ± 13 nm. The synthesis of a mixed composite, combining Cu and Ni2O3 within the PC matrix, was achieved through a two-step deposition process using a Ni2O3@PC template. An analysis of the resultant composite structure (Cu/Ni2O3@PC) confirmed the existence of CuNi (97.3%) and CuO (2.7%) crystalline phases. The synthesized catalysts were characterized by scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX), X-ray diffraction (XRD) analysis, and atomic force microscopy (AFM). In photodegradation assessments, the Cu/Ni2O3@PC mixed composite demonstrated higher photocatalytic activity, achieving a substantial 59% degradation of norfloxacin (NOR) under UV light irradiation. This performance surpassed that of both Ni2O3@PC and Cu@PC composites. The optimal pH for maximum NOR removal from the aqueous solution was determined to be pH 5, with a reaction time of 180 min. The degradation of NOR in the presence of these composites adhered to the Langmuir-Hinshelwood mechanism and a pseudo-first order kinetic model. The reusability of the catalysts was also investigated for 10 consecutive runs, without any activation or regeneration treatments. The Cu@PC membrane catalyst demonstrated a marked decline in degradation efficiency after the 2nd test cycle, ultimately catalyzing only 10% of NOR after the 10th cycle. In contrast, the Ni2O3@PC based catalyst demonstrated a more stable NOR degradation efficiency throughout all 10 runs, with 27% NOR removal observed during the final test. Remarkably, the catalytic performance of the Cu/Ni2O3@PC mixed composite remained highly active even after being recycled 4 times. The degradation efficiency exhibited a gradual reduction, with a 17% decrease after the 6th run and a cumulative 35% removal of NOR achieved by the 10th cycle. Overall, the findings indicate that Cu/Ni2O3@PC mixed composite membranes may represent an advancement in the quest to mitigate the adverse effects of antibiotic pollution in aquatic environments and hold significant promise for sustainable water treatment practices.

Synthesis, Characterization and Performance of Materials for a Sustainable Future

Today, sustainability represents the key factor for economic progress in compliance with social advancement and environmental protection, driving innovation in materials, processes and technologies [...].

Sustainable Removal of BTEX Gas Using Regenerated Metal Containing SiO2

In the last decades, the removal of benzene, toluene, ethylbenzene, and xylene (BTEX) has been considered a major environmental crisis. In this study, two novel nanocomposite materials (Fe2O3/SiO2 and Fe2O3-Mn2O3/SiO2) that have regeneration ability by UV irradiation have been fabricated to remove BTEX at ambient temperature. This research revealed that both nanocomposites could remove more than 85% of the BTEX in the first cycle. The adsorption capacities followed the order of ethylbenzene > m-xylene > toluene > benzene as in the molecular weight order. The reusability test using UV irradiation showed that the performance of Fe2O3/SiO2 decreased drastically after the fifth cycle for benzene. On the other hand, when Mn is located in the nanocomposite structure, Fe2O3-Mn2O3/SiO2 could maintain its adsorption performance with more than 80% removal efficiency for all the BTEX for ten consecutive cycles. The difference in the reusability of the two nanocomposites is that the electron energy (from the valence band to the conduction band) for BTEX decomposition is changed due to the presence of manganese. This study provides a promising approach for designing an economical reusable nanomaterial, which can be used for VOC-contaminated indoor air.

A Novel Metal-Containing Mesoporous Silica Composite for the Decolorization of Rhodamine B: Effect of Metal Content on Structure and Performance

A series of novel Mn_xFe_y@SiO₂ (x,y = 1-20%) nanocomposites were synthesized for the first time via the sol-gel/combustion method with different content of precursors (Mn and Fe acetate salts). The effect of precursor content and ratio on physicochemical properties were observed by various characterization methods. Moreover, Rhodamine B (RhB) was chosen as the target pollutant to test the performance of these nanocomposites under a photocatalytic Fenton-like reaction. The results showed that the nanocomposite morphology improved by increasing Fe and Mn content. In this study, interesting behavior was observed in BET results which were different from the fact that increasing metal content can decrease the surface area. This study revealed that one metal could be more critical in controlling the properties than another. Moreover, the precursor ratio appears to have a more tangible effect on the surface area than the effect of precursor content. Among all synthesized nanocomposites, Mn₁Fe₅@SiO₂ showed the highest surface area of 654.95 m²/g. At optimum batch conditions (temp = 25 °C, catalyst dosage = 1 g L^-1, H₂O₂ = 75 mmolL^-1, and initial RhB concentration = 50 mg L^-1), complete removal (simultaneous adsorption/degradation) occurred using Mn₁Fe₅@SiO₂ at neutral pH. This study showed that the designed nanomaterial could be used as a dual functional adsorbent/photocatalyst in different environmental applications.

Synthesis of Fe2O3/Mn2O3 Nanocomposites and Impregnated Porous Silicates for Dye Removal: Insights into Treatment Mechanisms

Fe2O3/Mn2O3 nanocomposites and impregnated porous silicates (Fe2O3/Mn2O3@SiO2 [FMS]) were prepared and investigated as catalytic adsorbents. The catalysts were applied for cationic and anionic dye pollutants in the adsorption, Fenton reaction, and photocatalysis processes at a pH of 7. Fe2O3/Mn2O3 nanoparticles (FM-NPs) were prepared using the co-precipitation method and were impregnated in SiO2 by the sol–gel process. The synthesized materials were characterized using various sophisticated techniques. Results indicated that the impregnation of bi-metallic NPs in SiO2 increased the surface area, and the function of the adsorbent also improved. FMS showed a significant adsorption effect, with 79.2% rhodamine B removal within 15 min. Fenton and photocatalyst reaction showed removal rates of 85.3% and 97.9%, respectively, indicating that negatively charged porous silicate attracts cationic pollutants. In the case of the anionic pollutant, Congo red, the adsorption reaction of FMS did not occur, and the removal rate of the photocatalyst reaction was 79%, indicating the repulsive force between the negatively charged silica and the anionic dye. Simultaneously, bi-metal-bonded FM-NPs facilitated the photocatalytic reaction, reducing the recombination of electron-hole pairs. This study provides new insights into the synthesis of FM-NPs and FMS as photocatalytic adsorbents and their photocatalytic mechanisms based on reaction conditions and contaminant characteristics. The developed materials have potential applications for environmental mitigation.