Energetic and Environmental Aspects of Individual Heat Generation for Sustainable Development at a Local Scale—A Case Study from Poland

Application of triple-branch artificial neural network system for catalytic pellets combustion

On the international level, it is common to act on reducing emissions from energy systems. However, in addition to industrial emissions, low-stack emissions also make a significant contribution. A good step in reducing its environmental impact, is to move to biofuels, including biomass. This paper examines the impact of placing a catalytic system in a retort boiler to minimize emissions of greenhouse gases, dust and other pollutants when burning pellets. The effect of platinum, and oxides of selected metals placed on the deflector as a solid catalyst was studied. Based on the experimental data, a branched artificial neural network was constructed and trained. The routing of three parallel topologies made it possible to achieve high accuracy while keeping the input data relatively simple. The system showed an average error of 3.54% against arbitrary test data. On the basis of experimental data as well as predictions returned by the artificial neural network, recommendations were shown for the catalysts used and their amounts. Depending on the biomass from which the pellet was produced, the experiment suggested the use of titanium or copper oxides. In the case of the neural network, it was able to select a better system, based on platinum, improving emission reductions by up to more than 19%, depending on the type of pellet used.

Impact of building types and CHP plants on air quality (2019-2021) in central-eastern European monocentric agglomeration

The quality of city air is influenced by many factors, including the density of buildings, the roughness of the terrain, the presence of street canyons, the heat sources in buildings, the types of industry, the topography, and meteorological conditions. Official air quality monitoring systems measure a very limited number of points, making local analysis impossible without the use of mathematical modeling programs. Here, we present an analysis of local air quality in an urban agglomeration. Data were collected over three years (2019, 2020, 2021), using commercial sensors located throughout the area of investigation. Dense downtown buildings equipped with individual heat sources were not found to have any impact on local air quality. The local municipal combined heat and power (CHP) plants contributed <1 ‰ of the measured concentration of particulate matter. Land height and the density of single-family housing were found to significantly affect air quality. We also took into account the influence of weather conditions, wind speed, and wind direction on the concentrations of particulate matter. High concentrations of particulate matter occurred only during heating periods when wind speeds were moderate. Wind direction did not have a direct impact on air quality, despite the expected benefits of ventilation through air corridors.

Influence of spatial distribution pattern of buildings on the distribution of urban gaseous pollutants

Buildings are the main component of urban, and their three-dimensional spatial patterns affect meteorological conditions and consequently, the spatial distribution of gaseous pollutants (CO, NO, NO₂, and SO₂). This study uses the Jinan Central District as the study area and constructs a building spatial distribution index system based on DEM, urban road network, and building big data. ANOVA and spatial regression models were used to study the effects of building spatial distribution indicators on the distribution of gaseous pollutants along with their spatial heterogeneity. The results showed that (1) the effects of most of spatial distribution indexes of building on the concentration distribution of the four gaseous pollutants were significant, with one-way ANOVA outcomes reaching a significance level of 0.01 or more. The DEM mean, building altitude, and their interaction with other building spatial distribution indicators are important factors affecting the distribution of gaseous pollutants; The interaction of other three-factor indicators did not have a significant effect on the distribution of gaseous pollutant concentrations. (2) The spatial distribution of CO and NO₂ is mainly influenced by the indicators of the spatial distribution of buildings in this study unit, and the effects of CO and NO₂ concentrations in adjacent study units are the result of the action of stochastic factors. The NO and SO₂ concentrations are influenced by the spatial distribution index of buildings in this study unit, the neighborhood homogeneity index, and NO and SO2 concentrations. (3) Spatial heterogeneity was observed in the effects of building spatial distribution indicators on the concentrations of different pollutants. The GWR models constructed using CO and NO concentrations and building spatial distribution indicators were well fitted globally and locally. The CO and NO concentrations were negatively correlated with the mean topographic elevation and NO concentrations were correlated with building density.

Analysis of Air Pollution around a CHP Plant: Real Measurements vs. Computer Simulations

This study examines the concentrations of air pollution in the vicinity of a combined heat and power plant (CHP) and a communication route, using computer modeling of pollutant dispersion and spatial analysis based on real measurements in the city of Łódź, Poland, Europe. The research takes into account the concentrations of particulate matter (PM10, PM2.5, PM1.0) and gaseous pollutants (SO2 and VOC) in winter and summer. The spatial distribution of pollutants is discussed, including the presence of areas with increased accumulations of pollutants. Because atmospheric air has no natural boundaries, when analyzing any location, not only local sources of pollution, but also background pollution, should be analyzed. A clear difference was observed between the concentrations of pollutants in the summer and winter seasons, with significantly higher concentrations in the winter (heating) period. The impacts of road transport, individual heating systems, and combined heat and power plants were also assessed. Computer calculations confirmed that road transport accounted for the largest share of both PM and SO2 emissions. The CHP plant was responsible for the smallest percentage of dust emissions and was the next largest producer of SO2 emissions. The share of the total emissions from the individual sources were compared with the results of detailed field tests. The numerical analysis of selected pollution sources in combination with the field analysis shows that the identified pollution sources included in the analysis represent only a part of the total observed pollutant concentrations (suggesting that other background sources account for the rest).

Selected Parameters of Oat Straw as an Alternative Energy Raw Material

Straw is treated as agricultural waste, and it is available in almost every region of Poland. A total of 30 million tons of straw is produced per year, of which there is a surplus of approximately 13.5 million tons of undeveloped straw. For energy purposes, straw from cereals or rapeseed is most often used. When analyzing scientific publications, it was noticed that, in Poland, large amounts of oat straw are produced, and there is no alternative use for it. Hence, we conducted research to determine the energy value of oat straw. Raw material was obtained from an individual farm from 2018 to 2020. Selected energy parameters for straw burned alone (100%) or co-fired with coal were analyzed in the following weight proportions: 70/30, 80/20, and 90/10 coal/oat straw. It was shown that changing weather conditions, in particular years, had a modifying effect on some of the energy parameters of straw. The calorific value of straw was lower than that of coal, but its impact on environmental pollution turned out to be significantly lower. The difference in combustion heat between coal and straw was 11.74 MJ·kg−1. Investigations into pollutant concentrations were performed for cubes of compressed straw and hard coal. Mixtures of these fuels were not studied in this part of the work. The combustion of straw resulted in a reduction of harmful NO, NOX, and SO2 pollutants and an increase in CO compared to coal combustion. As for hydrogen content—it was the highest in carbon and the lowest in straw. In the case of analytical moisture, an inverse relationship was observed. In the case of both coal and straw, the ash content varied throughout the years of research. As the boiler power increased from 5 to 25 kW, the consumption of burned raw material increased significantly. The results indicate that the surplus of oat straw can be rationally used to obtain thermal energy, including co-combustion with coal. This will allow one to avoid burning straw in the fields, which causes great harm to the natural environment.

The Impact of Local Anti-Smog Resolution in Cracow (Poland) on the Concentrations of PM10 and BaP Based on the Results of Measurements of the State Environmental Monitoring

As a result of conducted air quality policy, including recent legal regulations (the local anti-smog resolution), the number of individual solid fuel heating devices in Cracow (Poland) gradually decreased. Reports on air quality in the city indicate that the concentration of pollutants in Cracow’s air shows a downward trend. However, a similar tendency in terms of improving air quality is also observed in the entire voivodeship, where, as a result of analogous although less radical measures, the number of individual solid fuel heating devices is also decreasing. The paper discusses the impact of legal regulations in Cracow on the improvement of air quality in the context of changes taking place in nearby cities. Trends in changes in PM10 and BaP (PM10) concentrations are analyzed. The rate of decline of the analyzed pollutants concentrations is estimated with the use of nonparametric linear regression. Analysis showed that the rate of decline in the average annual concentrations of PM10 and BaP (PM10) in Cracow is always higher than for the analyzed cities of the Malopolskie Voivodeship. The difference is more pronounced with regard to the months of the heating season. The rate of changes for the average annual BaP (PM10) concentrations in Cracow, compared to other analyzed cities of the Malopolskie Voivodeship, is more intensive than in the case of PM10 concentrations (1.5 times stronger with regard to the months of the heating season). Since the concentration of BaP (PM10) is a better indicator of the effects of liquidation of high-emission furnaces than the concentration of PM10, it can be concluded that the impact of actions related to the improvement of air quality in Cracow in the context of changes taking place in selected cities of the Malopolskie Voivodeship is more visible.

Empirical ozone isopleths at urban and suburban sites through evolutionary procedure-based models

Ozone (O₃) is a reactive oxidant that causes chronic effects on human health, vegetation, ecosystems and materials. This study aims to create O₃ isopleths in urban and suburban environments, based on machine learning with air quality data collected from 2001 to 2017 at urban (EA) and suburban (CC) monitoring stations from Madrid (Spain). Artificial neural network (ANN) models have powerful fitting performance, describing correctly several complex and nonlinear relationships such as O₃ and his precursors (VOC and NO_x). Also, ANN learns from the experience provided by data, contrary to mechanistic models based on the fundamental laws of natural sciences. The determined isopleths showed a different behaviour of the VOC-NO_x-O₃ system compared to the one achieved with a mechanistic model (EKMA curve): e.g. for constant NO_x concentrations, O₃ concentrations decreased with VOC concentrations in the ANN model. Considering the difficulty to model all the phenomena (and acquired all the required data) that influences O₃ concentrations, the statistical models may be a solution to describe this system correctly. The applied methodology is a valuable tool for defining mitigation strategies (control of precursors' emissions) to reduce O₃ concentrations. However, as these models are obtained by air quality data, they are not geographical transferable.

Old and Modern Wooden Buildings in the Context of Sustainable Development

Construction is a powerful industry that is not indifferent to the environment. Neither the maintenance of buildings in a proper technical condition nor their eventual demolition is indifferent to the environment. The main threats to the environment are still the inefficient use of construction materials and energy needed for their production and installation, as well as the emission of harmful substances to the environment at the stage of operation of buildings and their demolition. This article discusses the importance of wood as a renewable material in terms of its physical and mechanical properties. The restoration of forest areas is of great importance to the global ecosystem and the sustainable development system, reducing the threat of global warming and the greenhouse effect by reducing CO2 levels. In addition, demolition wood can be reused in construction, can be safely recycled as it quickly decomposes, or can be used as a source of renewable energy. The preservation of existing timber-framed buildings in good condition contributes to a lower consumption of this raw material for repair, which already significantly reduces the energy required for their manufacture, transport, and assembly. This also reduces the amount of waste that would have to be disposed of in various ways. Both at the stage of design, execution, and then exploitation, one forgets about the physical processes taking place inside the partitions and about the external climatic influences of the environment (precipitation, water vapor, and temperature) on which the type, intensity, and extent of chemical and biological corrosion depend to a very high degree. This paper presents examples of the influence of such impacts on the operational safety of three selected objects: a feed storehouse and an officer casino building from the second half of the nineteenth century and an 18th century rural homestead building. The research carried out on wooden structures of the above-mentioned objects “in situ” was verified by means of simulation models, which presented their initial and current technical conditions in relation to the type and amount of impact they should safely absorb. Moreover, within the framework of this paper, artificial intelligence methods have been implemented to predict the biological corrosion of the structures studied. The aim of the paper was to draw attention to the timber already built into buildings, which may constitute waste even after several years of operation, requiring disposal and at the same time the production of a substitute. The purpose of the research carried out by the authors of the article was to examine the older and newer buildings in use, the structures of which, in whole or in part, were made of wood. On a global scale, there will be considerable demand for the energy required to thermally dispose of this waste or to deposit it in landfills with very limited capacity until its complete biological decomposition. These energy demands and greenhouse gas emissions can be prevented by effective diagnostics of such structures and the predictability of their behaviour over time, with respect to the conditions under which they are operated. The authors of the article, during each assessment of the technical condition of a building containing wooden elements, analysed the condition of their protection each time and predicted the period of their safe life without the need for additional reinforcements or replacement by others. As the later reality shows, it is a very effective method of saving money and energy.

Mineralogical and Chemical Tracing of Dust Variation in an Underground Historic Salt Mine

The aim of this study was to investigate the causes of the evolution of atmospheric dust composition in an open-to-public subterranean site (UNESCO-recognized historic mine) at increasing distances from the air intake. The role of the components imported with atmospheric air from the surface was compared with natural and anthropogenic sources of dust from inside the mine. Samples of deposited dust were directly collected from flat surfaces at 11 carefully selected sites. The morphological, mineralogical, and chemical characteristics were obtained using scanning electron microscopy (SEM), X-ray diffraction (XRD), and inductively coupled plasma spectroscopy (ICP). The study showed that the air in the underground salt mine was free of pollutants present in the ambient air on the surface. Most of the components sucked into the mine by the ventilation system from the surface (regular dust, particulate matter, gaseous pollutants, biogenic particles, etc.) underwent quick and instantaneous sedimentation in the close vicinity of the air inlet to the mine. The dust settled in the mine interior primarily consisted of natural geogenic particles, locally derived from the weathering of the host rock (halite, anhydrite, and aluminosilicates). This was confirmed by low values of enrichment factors (EF) calculated for minor and trace elements. Only one site, due to the tourist railroad and the associated local intensive tourist traffic, represented the anthropogenic sources of elevated concentrations of ferruginous particles and accompanied metals (P, Cr, Mn, Co, Ni, Cu, As, Mo, Cd, Sn, Sb, Pb, and W). The gravitational deposition of pollutants from these sources limits the effects of the emissions to the local range. The used methodology and the results are universal and might also apply to other mines, caves, or underground installations used for museums, tourists, or speleotherapeutic purposes.

Prospects of Using Hydrocarbon Deposits from the Autochthonous Miocene Formation (Eastern Carpathian Foredeep, Poland) for Geothermal Purposes

There are many oil and gas fields around the world where the vast number of wells have been abandoned or suspended, mainly due to the depletion of reserves. Those abandoned oil and gas wells (AOGWs) are often located in areas with a prospective geothermal potential and might be retrofitted to a geothermal system without high-cost drilling. In Poland, there are thousands of wells, either operating, abandoned or negative, that might be used for different geothermal applications. Thus, the aim of this paper is not only to review geothermal and petroleum facts about the Eastern Carpathian Foredeep, but also to find out the areas, geological structures or just AOGWs, which are the most prospective in case of geothermal utilization. Due to the inseparability of geological settings with both oil and gas, as well as geothermal conditionings, firstly, the geological background of the analyzed region was performed, considering mainly the autochthonous Miocene formation. Then, geothermal and petroleum detailed characteristics were made. In the case of geothermal parameters, such as formation’s thickness, temperatures, water-bearing horizons, wells’ capacities, mineralization and others were extensively examined. Considering oil and gas settings, insights into reservoir rocks, hydrocarbon traps and migration paths issues were created. Then, for evaluating geothermal parameters for specific hydrocarbon reservoirs, their depths were established based on publicly available wells data. Thereafter, the average temperatures for selected reservoirs were set. As the effect, it turned out that most of the deposits have average temperatures of 40/50 °C, nonetheless, there are a few characterized by higher (even around 80 °C) temperatures at reasonable depths.

Thermal Modernization Cost and the Potential Ecological Effect—Scenario Analysis for Thermal Modernization in Southern Poland

Air pollution is one of the important environmental problems in Poland. The main cause of its occurrence is emissions associated with individual heating of buildings. The reduction of the primary energy demand in a building is influenced by its proper thermal modernization, including in particular insulating. In view of the above, this article presents the results of studies on the possible environmental benefits of thermal modernization of single-family houses for the area of Southern Poland. The analysis was limited to determining the impact of measures to reduce air pollution emissions by insulating the building envelope of single-family houses. The research was conducted for two voivodeships: Śląskie and Małopolskie. Its aim is to identify the financial costs and achievable ecological effects of the thermal modernization of single-family buildings. The geographical selection of the research area was based on the fact that it covers the most polluted region in Poland. This region is characterized by many features that influence poor air quality. Among these features, the most important are: diversified building structure, a diverse topography, and very high population density. To limit multiple variables, we have selected a scenario method that has already been used in similar research. Four scenarios were established to show the relationship between the value of emission reductions and the level of funding for thermal modernization. The analysis allows a comparison of the effectiveness of individual variants and the transposition of their results into the possibilities of action in the region. This research will help to supplement the knowledge of the impact of insulating building envelopes on reducing pollutant emissions by reducing the energy demand of a building. They also identify a possible link between the level of this reduction and the grant amount for thermal modernization. As a result, it was found that a high share of external funding—stimulating the tendency of the inhabitants of the analyzed voivodeships to effective thermal modernization, and thus reducing the buildings’ energy consumption—has a significant impact on the improvement of air quality.

Energy Effectiveness or Economic Profitability? A Case Study of Thermal Modernization of a School Building

Thermal refurbishment of buildings results in certain energy, financial, and environmental effects. Such investments are financially supported in Poland after meeting the legally defined conditions of thermal protection and energy consumption. This paper presents a complex thermal modernization of a school building, performed by following Polish regulations. A detailed description of the studied object was given, and the calculation procedure was described. Then an optimal variant of an investment and an ex-post analysis were described. Simple payback time (SPBT) of modernization measures was from 15.8 years (insulation of the ceiling under the unheated attic) to 87 years for insulation of the wooden external wall, with 35.6 years for the whole project, which is shorter than the predicted lifespan of the whole building (50–70 years). Annual calculated heating demand decreased from 464.78 to 168.73 GJ, resulting in the primary energy consumption indicator (EP) of 484.44 and 129.46 kWh/m2, respectively. Thermal refurbishment with the replacement of an old boiler into a new wood-pellet one resulted in a significant reduction of SO2 and dust emissions from 451 to 27.5 kg and from 399 to 13 kg, respectively.

Mapping the susceptibility of UNESCO World Cultural Heritage sites in Europe to ambient (outdoor) air pollution

Air pollution, particularly in urban areas, is a concern for its negative effects on the materials of the built environment. Cities are also home to a large part of our cultural heritage. Air pollution accelerates the natural processes of deterioration of the materials of historic buildings and monuments, causing premature aging and reducing their aesthetic value. The present paper aims to assess the current potential damage due to air pollution on different materials through Europe. Several corrosion and soiling maps were produced by applying widely used dose-response functions. One of the priorities of this study was to provide an estimate of the effects of air pollution on UNESCO World Heritage cultural sites throughout Europe. The potential risk for cultural heritage monuments was estimated on the basis of exceeding tolerable degradation thresholds suggested for each material. The results show that, despite the significant improvements in air quality in Europe over the past few decades, air pollution is still considerable and continues to be an important agent of degradation of cultural heritage, particularly in anthropized areas. Although the methodology used in this study provides a simplified assessment of the likelihood of damage to UNESCO's cultural heritage in Europe from air pollution, it provides a unique perspective and the potential risk is assessed on a common basis. The results obtained contribute to a better understanding of the existing risk deriving from atmospheric pollution and to highlighting those sites, generally located in areas where anthropogenic activity is relevant, that need particular attention. The present paper can serve as a basis for stimulating additional studies and site-specific analyzes, as well as highlighting the need for further measures and policies for atmospheric pollution reduction in cities and in the surroundings of sensitive historic buildings and monuments to prevent further damage.

The Economic Effects of New Patterns of Energy Efficiency and Heat Sources in Rural Single-Family Houses in Poland

In the face of severe air pollution and implementation of energy and climate policy, it remains a challenge to develop effective strategies addressing the problem of solid fuels use in single-family houses (SFH) in rural areas in Poland. This study investigated the correlations between thermal modernization of SFH, the changes of heat sources from coal to clean energy, including heat pumps driven by prosumers’ photovoltaic (PV) installation, and the disposable income of households in Polish rural areas. It also provided an analysis of the current support mechanisms promoting energy efficiency and PV development. The application of simulation modelling of energy consumption and costs in the research has proved that comprehensive thermal modernization of rural SFH constructed in the period of 1945–1970 and investments supporting PV/heat pump systems would enable the most cost-effective way of heating to be implemented. Considering that, today, spending on energy for heat puts a burden on the budget of rural households, especially those living in the SFH aged 50 years and more that dominate rural areas in Poland, the changes in energy supply–demand patterns would be an enhancement of their economic, energy and environmental security. The research argued that, in the wider process of energy transformation and solving air pollution problems, the role of rural households should not be neglected in public policy.

Low Enthalpy Geothermal Resources for Local Sustainable Development: A Case Study in Poland

Many regions in Poland face the problem of air pollution. These regions include, though are not exclusive, to health resorts, an important element of the healthcare industry. Poor air quality is mainly associated with the domestic sector, which is dominated by individual solid fuel and coal boilers. One option for reducing emissions is to use alternative energy sources for heating purposes. Therefore, the paper presents an analysis into the possibility of using low enthalpy (low temperature) geothermal energy in health resort areas. The main purpose of the article is to estimate the potential of soil and water as the lower source for a heat pump. The article presents analyses of geological and hydrogeological conditions based on which the thermal parameters of the rock mass were determined, which were thermal conductivity and unit heat output for 1800 operating hours per year. The calculated values were used to perform a spatial analysis of the data and create maps of the average thermal conductivity for horizontal ground heat exchangers (HGHE) to a depth of 2 and 10 m and vertical ground heat exchangers (VGHE) in depth ranges up to 30, 60, and 90 m. The heating power of the intakes, located in the research area, were estimated using empirical formulas. In addition, a detailed analysis of the physicochemical parameters of groundwater in terms of the requirements indicated by four heat pump manufacturers is presented. The results of the presented research makes it possible to assess the potential of low-temperature geothermal energy and to characterize the suitability of the selected location for the use of HGHE, VGHE, and wells. As a result, the discussed area was found to have a high potential for the use of ground source heat pumps and a moderate potential for the use of low-temperature systems based on groundwater.

Techno-Economic Assessment of Mobilized Thermal Energy Storage System Using Geothermal Source in Polish Conditions

The paper considers technical and economic possibilities to provide geothermal heat to individual recipients using a mobile thermal storage system (M-TES) in Polish conditions. The heat availability, temperature and heat cost influence the choice of location—Bańska Niżna, near Zakopane in the southern part of the Poland. The indirect contact energy storage container was selected with phase change material characterized by a melting temperature of 70 °C and a heat storage capacity of 250 kJ/kg, in the amount of 800 kg. The economic profitability of the M-TES system (with a price per warehouse of 6000 EUR, i.e., a total of 12,000 EUR—two containers are needed) can be achieved for a heat demand of 5000 kWh/year with the price of a replaced heat source at the level of 0.21 EUR/kWh and a distance between the charging station and building (heat recipient) of 0.5 km. For the heat demand of 15,000 kWh/year, the price for the replaced heat reached EUR 0.11/kWh, and the same distance. In turn, for a demand of 25,000 kWh/year, the price of the replaced heat source reached 0.085 EUR/kWh. The distance significantly affected the economic profitability of the M-TES system—for the analyzed case, a distance around 3–4 km from the heat source should be considered.

Sustainable Utilization of Low Enthalpy Geothermal Resources to Electricity Generation through a Cascade System

The article presents an assessment of the potential for using low temperature geothermal water from the C-PIG-1 well (Małopolskie Voivodship, southern Poland) for electricity generation, as the first stage in a geothermal cascade system. The C-PIG-1 well is characterised by a temperature of geothermal water of 82 °C and a maximum flow rate of 51.22 kg/s. Geothermal water is currently only utilised for recreation purposes in swimming pools. In such locations, with the potential to use renewable energy for energetic purposes, the possibility of comprehensive management of the geothermal waters extracted should be considered both in the first stage of the cascade and after recreational use. Thermodynamic calculations were conducted assuming the use of the Organic Rankine Cycle (ORC) or Kalina Cycle. Two variants were analysed—the use of the maximum flow rate of geothermal waters and partial use with an assumption of a priority for recreational/heating purposes. The analysis and calculations indicate that the gross capacity in the most optimistic variant will not exceed 250 kW for the ORC and 440 kW for the Kalina Cycle. As far as the gross electricity generation is concerned, for ORC this will not exceed 1.9 GWh/year and for the Kalina Cycle it will not exceed 3.5 GWh/year.

Tools for Measuring Energy Sustainability: A Comparative Review

This paper is intended to perform a comparative and qualitative review among eight tools to measure energy sustainability. Therefore, it was necessary to create a theoretical and conceptual framework based on four criterias of selection and six categories of comparison. In this work, the conceptual bases that supported the research and the methodology created to carry out the comparative review will be presented. This analysis was based on the intrinsic concepts of energy sustainability of each of the reviewed tools with a critical qualitative analysis. Some conclusions shown through the conceptual framework developed that it was possible to apply an innovative methodology to qualitatively compare different tools to measure sustainability. The importance of this reflects the difficulty of conceptualizing the subjectivity of sustainable development, as shown throughout the paper, where it is often not possible to obtain a measurable result since the measured phenomenon is too complex to reduce it to a numerical value.

Selected Aspects of Combustion Optimization of Coal in Power Plants

Growing ecological standards force the implementation of solutions that will contribute to reducing greenhouse gas (GHG) emissions to the atmosphere. This is particularly important in Poland, whose energy system is almost 80% based on coal. In the interest of low carbon development it is worth considering the optimization of existing old coal-based power plants. The main goal of the research was to present the benefits of modernization of existing boiler equipment and to analyze the combustion process of various types of coal sorts that have a significant impact on the optimization of the production processes of energy media. An analysis of the processes occurring in boiler devices during the combustion of fuel was carried out, which had a significant impact on the quality of generated heat and electricity. The conducted research defined technological solutions for boiler structures that have a significant impact on improving the efficiency of the technological process in heating plants and the characteristics of coal as energy fuel. Practical technical and modernization solutions have been proposed that contribute to the optimization of coal combustion processes, resulting in increased energy efficiency of the heating plant.

Assessment of the Effective Variants Leading to Higher Efficiency for the Geothermal Doublet, Using Numerical Analysis‒Case Study from Poland (Szczecin Trough)

Numerical models of geothermal doublet allows us to reduce the high risk associated with the selection of the most effective location of a production well. Furthermore, modeling is a suitable tool to verify possible changes in operational geothermal parameters, which guarantees liveliness of the system. An appropriate selection of software as well as the methodology used to generate numerical models significantly affects the quality of the obtained results. In this paper, the authors discuss the influence of such parameters as grid density and distance between wells on the efficiency of geothermal heating plant. The last stage of the analysis was connected with estimation of geothermal power potential for a hypothetical geothermal doublet. Numerical simulations were carried out using the TOUGH2 code, which applies the finite-difference method. The research was conducted in the Szczecin Trough area (NW Poland), based on archival data from Choszczno IG-1 well. The results demonstrated that in the studied case of the Choszczno region, the changes in the distance of boreholes can have a visible influence on obtained results; however the grid density of the numerical model did not achieve a significant impact on it. The results show the significant importance of numerical modeling aimed at increasing the efficiency of a potential geothermal heating plant.

The Potential of RES in the Reduction of Air Pollution: The SWOT Analysis of Smart Energy Management Solutions for Krakow Functional Area (KrOF)

Health impacts and a decrease in the quality of life caused by air pollution is a major problem worldwide. Krakow is one of the most affected cities in the EU by air pollution mostly caused by burning solid fuels in households’ furnaces. It is considered that the most effective remedies would be adequate spatial planning solutions and application of low-emission sources including renewable energy sources (RES). This article draws from the analysis of the use of RES as a means for reducing harmful emissions in Krakow Functional Area (KrOF). The inventories of renewable energy sources and systems were compiled by the authors as a part of the EU project “Smart Edge—Sustainable Metropolitan Areas and the Role of The Edge City”. Using the data from the inventories, a SWOT analysis has been carried out to identify factors that determine the smart management of the RES potential, particularly the decisions of households on the transition towards RES. The results of the analysis have shown that many actions have been taken at the national, regional, and local levels but the greatest influence bear the solutions initiated and implemented at the communal level. The conclusion is that legislative regulations should be combined with locally tailor-made instruments. The proposed method of analysis can be applied in other metropolitan areas as a diagnostic procedure supporting action planning to solve air-quality problems caused by distributed emission sources.

Geological and Thermodynamic Analysis of Low Enthalpy Geothermal Resources to Electricity Generation Using ORC and Kalina Cycle Technology

The article presents an assessment of the potential for using low enthalpy geothermal resources for electricity generation on the basis of the Małopolskie Voivodeship (southern Poland). Identification the locations providing the best prospects with the highest efficiency and possible gross power output. Thermodynamic calculations of power plants were based on data from several geothermal wells: the Bańska PGP-1, Bańska IG-1, Bańska PGP-3 and Chochołów PIG-1 which are working wells located in one of the best geothermal reservoirs in Poland. As the temperature of geothermal waters from the wells does not exceed 86 °C, considerations include the use of binary technologies—the Organic Rankine Cycle (ORC) and Kalina Cycle. The potential gross capacity calculated for existing geothermal wells will not exceed 900 kW for ORC and 1.6 MW for Kalina Cycle. In the case of gross electricity, the total production will not exceed 3.3 GWh/year using the ORC, and will not exceed 6.3 GWh/year for the Kalina Cycle.

Review of the Low-Enthalpy Lower Cretaceous Geothermal Energy Resources in Poland as an Environmentally Friendly Source of Heat for Urban District Heating Systems

The paper presents a review of the geological and hydrogeological data of the Lower Cretaceous aquifer in the Polish Lowlands and discusses the possibilities for the utilisation of geothermal water resources in existing and new district heating systems. Based on experience related to the use of thermal waters in existing geothermal systems, and using data from the literature, assessments have been made of the energy and environmental effects of the application of low-enthalpy geothermal resources from the Lower Cretaceous aquifer as a source of heat for urban district heating systems. The authors concluded that the implementation of such solutions could result in the production of approximately 4 PJ of geothermal energy annually. To date, these resources have only been developed in three locations—Mszczonów, Uniejów and Poddębice—with the total amount of energy generated annually reaching 100 TJ/year. Similar district heating networks in 120 nearby localities have been also identified. Here, specified geological and hydrogeological conditions enable the extraction of heat from the investigated Lower Cretaceous aquifer, with the aim of using this for heating purposes. To achieve this goal, multiple measures are required, including the following: raising public awareness through appropriate education programmes aimed at the youngest school children; systemic, efficient energy management measures at the central, regional and local levels, and providing financial support and ensuring regulations and laws aimed at improving the development of geothermal resources.

Assessment of Reducing Pollutant Emissions in Selected Heating and Ventilation Systems in Single-Family Houses

The article presents the results of a study aiming to select the optimal source of heat for a newly designed single-family home. Commercial software was used to compare heating and ventilation systems involving a bituminous coal boiler, a condensing gas boiler, a biomass boiler, a heat pump with water and glycol as heat transfer media. The effectiveness of natural ventilation, mechanical ventilation with a ground-coupled heat exchanger, and solar heater panels for water heating were evaluated. The analysis was based on the annual demand for useful energy, final energy, and non-renewable primary energy in view of the pollution output of the evaluated heating systems. The analysis revealed that the heat pump with water and glycol was the optimal solution. However, the performance of the heat pump in real-life conditions was below its maximum theoretical efficiency. The biomass boiler contributed to the highest reduction in pollutant emissions (according to Intergovernmental Panel on Climate Change Change guidelines, carbon dioxide emissions have zero value), but it was characterized by the highest demand for final energy. Mechanical ventilation with heat recovery was required in all analyzed systems to achieve optimal results. The introduction of mechanical ventilation decreased the demand for final energy by 10% to around 40% relative to the corresponding heating systems with natural ventilation.