Negative Reagent Ions for Real Time Detection Using SIFT-MS

Robust Automated SIFT-MS Quantitation of Volatile Compounds in Air Using a Multicomponent Gas Standard

Selected ion flow tube mass spectrometry, SIFT-MS, has been widely used in industry and research since its introduction in the mid-1990s. Previously described quantitation methods have been advanced to include a gas standard for a more robust and repeatable analytical performance. The details of this approach to calculate the concentrations from ion-molecule reaction kinetics based on reaction times and instrument calibration functions determined from known concentrations in the standard mix are discussed. Important practical issues such as the overlap of product ions are outlined, and best-practice approaches are presented to enable them to be addressed during method development. This review provides a fundamental basis for a plethora of studies in broad application areas that are possible with SIFT-MS instruments.

Accurate selected ion flow tube mass spectrometry quantification of ethylene oxide contamination in the presence of acetaldehyde

In September 2020, traces of ethylene oxide (a toxic substance used as a pesticide in developing countries but banned for use on food items within the European Union) were found in foodstuffs containing ingredients derived from imported sesame seed products. Vast numbers of foodstuffs were recalled across Europe due to this contamination, leading to expensive market losses and extensive trace exposure of ethylene oxide to consumers. Therefore, a rapid analysis method is needed to ensure food safety by high-throughput screening for ethylene oxide contamination. Selected ion flow tube mass spectrometry (SIFT-MS) is a suitable method for rapid quantification of trace amounts of vapours in the headspace of food samples. It turns out, however, that the presence of acetaldehyde complicates SIFT-MS analyses of its isomer ethylene oxide. It was proposed that a combination of the H3O+ and NO+ reagent ions can be used to analyse ethylene oxide in the presence of acetaldehyde. This method is, however, not robust because of the product ion overlaps and potential interferences from other matrix species. Thus, we studied the kinetics of the reactions of the H3O+, NO+, OH- and O-˙ ions with these two compounds and obtained their rate coefficients and product ion branching ratios. Interpretation of these experimental data revealed that the OH- anions are the most suitable SIFT-MS reagents because the product ions of their reactions with acetaldehyde (CH2CHO- at m/z 43) and ethylene oxide (C2H3O2- at m/z 59) do not overlap.

How to Use Ion-Molecule Reaction Data Previously Obtained in Helium at 300 K in the New Generation of Selected Ion Flow Tube Mass Spectrometry Instruments Operating in Nitrogen at 393 K

Selected ion flow tube mass spectrometry (SIFT-MS) instruments have significantly developed since this technique was introduced more than 20 years ago. Most studies of the ion-molecule reaction kinetics that are essential for accurate analyses of trace gases and vapors in air and breath were conducted in He carrier gas at 300 K, while the new SIFT-MS instruments (optimized to quantify concentrations down to parts per trillion by volume) operate with N₂ carrier gas at 393 K. Thus, we pose the question of how to reuse the data from the extensive body of previous literature using He at room temperature in the new instruments operating with N₂ carrier gas at elevated temperatures. Experimentally, we found the product ions to be qualitatively similar, although there were differences in the branching ratios, and some reaction rate coefficients were lower in the heated N₂ carrier gas. The differences in the reaction kinetics may be attributed to temperature, an electric field in the current flow tubes, and the change from He to N₂ carrier gas. These results highlight the importance of adopting an updated reaction kinetics library that accounts for the new instruments' specific conditions. In conclusion, almost all previous rate coefficients may be used after adjustment for higher temperatures, while some product ion branching ratios need to be updated.

A SIFT-MS study of positive and negative ion chemistry of the ortho-, meta- and para-isomers of cymene, cresol, and ethylphenol

Selected Ion Flow Tube Mass Spectrometry (SIFT-MS) is a soft ionisation technique based on gas phase ion-molecule reaction kinetics for the quantification of trace amounts of volatile organic compound vapours. One of its previous limitations is difficulty in resolving isomers, although this can now be overcome using different reactivities of several available reagent cations and anions (H₃O⁺, NO⁺, O₂⁺˙, O^-˙, OH^-, O₂^-˙, NO₂^-, NO₃^-). Thus, the ion-molecule reactions of these eight ions with all isomers of the aromatic compounds cymene, cresol and ethylphenol were studied to explore the possibility of their immediate identification and quantification without chromatographic separation. Rate coefficients and product ion branching ratios determined experimentally for the 72 reactions are reported. DFT calculations of their energetics confirmed the feasibility of the suggested reaction pathways. All positive ion reactions proceeded fast but largely did not discriminate between the isomers. The reactivity of the anions was much more varied. In all cases, OH^- reacts by proton transfer forming (M-H); NO₂^- and NO₃^- were unreactive. The differences observed for product ion branching ratios can be used to identify isomers approximately.

Recent developments and applications of selected ion flow tube mass spectrometry (SIFT-MS)

Selected ion flow tube mass spectrometry (SIFT-MS) is now recognized as the most versatile analytical technique for the identification and quantification of trace gases down to the parts-per-trillion by volume, pptv, range. This statement is supported by the wide reach of its applications, from real-time analysis, obviating sample collection of very humid exhaled breath, to its adoption in industrial scenarios for air quality monitoring. This review touches on the recent extensions to the underpinning ion chemistry kinetics library and the alternative challenge of using nitrogen carrier gas instead of helium. The addition of reagent anions in the Voice200 series of SIFT-MS instruments has enhanced the analytical capability, thus allowing analyses of volatile trace compounds in humid air that cannot be analyzed using reagent cations alone, as clarified by outlining the anion chemistry involved. Case studies are reviewed of breath analysis and bacterial culture volatile organic compound (VOC), emissions, environmental applications such as air, water, and soil analysis, workplace safety such as transport container fumigants, airborne contamination in semiconductor fabrication, food flavor and spoilage, drugs contamination and VOC emissions from packaging to demonstrate the stated qualities and uniqueness of the new generation SIFT-MS instrumentation. Finally, some advancements that can be made to improve the analytical capability and reach of SIFT-MS are mentioned.

Study of the Chemical Ionization of Organophosphate Esters in Air Using Selected Ion Flow Tube-Mass Spectrometry for Direct Analysis

Organophosphate esters are an emerging environmental concern since they spread persistently across all environmental compartments (air, soil, water, etc.). Measurements of semivolatile organic compounds are important but not without challenges due to their physicochemical properties. Selected ion flow tube-mass spectrometry (SIFT-MS) can be relevant for their analysis in air because it is a direct analytical method without separation that requires little preparation and no external calibration. SIFT-MS is based on the chemical reactivity of analytes with reactant ions. For volatile and semivolatile organic compound analysis in the gas phase, knowledge of ion-molecule reactions and kinetic parameters is essential for the utilization of this technology. In the present work, we focused on organophosphate esters, semivolatile compounds that are now ubiquitous in the environment. The ion-molecule reactions of eight precursor ions that are available in SIFT-MS (H₃O⁺, NO⁺, O₂^•+, OH^-, O^•-, O₂^•-, NO₂^-, and NO₃^-) with six organophosphate esters were investigated. The modeling of ion-molecule reaction pathways by calculations supported and complemented the experimental work. Organophosphate esters reacted with six of the eight precursor ions with characteristic reaction mechanisms, such as protonation with hydronium precursor ions and association with NO⁺ ions, while nucleophilic substitution occurred with OH^-, O^•-, and O₂^•-. No reaction was observed with NO₂^- and NO₃^- ions. This work shows that the direct analysis of semivolatile organic compounds is feasible using SIFT-MS with both positive and negative ionization modes.

Ternary association reactions of H3 O+ , NO+ and O2 +• with N2 , O2 , CO2 and H2 O; implications for selected ion flow tube mass spectrometry analyses of air and breath

RATIONALE

The reactions of the reagent ions used for trace gas analysis in selected ion flow tube mass spectrometry (SIFT-MS), R⁺ , viz. H₃ O⁺ , NO⁺ and O₂ ⁺ , with the major gases in air and breath samples, M, viz. N₂ , O₂ , CO₂ and H₂ O, are investigated. These reactions are seen to form weakly-bound adduct ions, R⁺ M, by ternary association reactions that must not be mistaken for genuine volatile organic compound (VOC) analyte ions.

METHODS

The ternary association rate coefficients mediated by helium (He) carrier gas atoms, k_3a , have been determined for all combinations of R⁺ and M, which form R⁺ M adduct ions ranging in m/z from 47 (H₃ O⁺ N₂ ) to 76 (O₂ ^+• CO₂ ). This was achieved by adding variable amounts of M (up to 0.5 mbar pressure) into the He carrier gas (pressure of 1.33 mbar) in a SIFT-MS flow tube at 300 K. Parabolic curvature was observed on some of the semi-logarithmic decay curves that allowed the rate coefficients mediated by M molecules, k_3b , to be estimated.

RESULTS

Values of k_3a were found to range from 1 × 10^-31  cm⁶  s^-1 to 5 × 10^-29  cm⁶  s^-1 , which form mass spectral R⁺ M "ghost peaks" of significant strength when analysing VOCs at parts-per-billion concentrations. It was seen that the R⁺ M adduct ions (except when M is H₂ O) react with H₂ O molecules by ligand switching forming the readily recognised monohydrates of the initial reagent cations R⁺ H₂ O. Whilst this ligand switching diminishes the R⁺ M adduct ghost peaks, it does not eliminate them entirely.

CONCLUSIONS

The significance of these adduct ions for trace gas analysis by SIFT-MS in the low m/z region is alluded to, and some examples are given of m/z spectral overlaps of the R⁺ M and R⁺ H₂ O adduct cations with analyte cations of VOCs formed by analysis of complex media like exhaled breath, warning that ghost peaks will be enhanced using nitrogen carrier gas in SIFT-MS.

Volatile fingerprint of food products with untargeted SIFT-MS data coupled with mixOmics methods for profile discrimination: Application case on cheese

Volatile organic compounds (VOCs) emitted by food products are decisive for the perception of aroma and taste. The analysis of gaseous matrices is traditionally done by detection and quantification of few dozens of characteristic markers. Emerging direct injection mass spectrometry technologies offer rapid analysis based on a soft ionisation of VOCs without previous separation. The recent increase of selectivity offered by the use of several precursor ions coupled with untargeted analysis increases the potential power of these instruments. However, the analysis of complex gaseous matrix results in a large number of ion conflicts, making the quantification of markers difficult, and in a large volume of data. In this work, we present the exploitation of untargeted SIFT-MS volatile fingerprints of ewe PDO cheeses in a real farm model, using mixOmics methods allowing us to illustrate the typicality, the manufacturing processes reproducibility and the impact of the animals' diet on the final product.

The potential of NO+ and O2 +• in switchable reagent ion proton transfer reaction time-of-flight mass spectrometry

Selected ion flow tube mass spectrometry (SIFT-MS) and proton transfer reaction mass spectrometry with switchable reagent ion capability (PTR+SRI-MS) are analytical techniques for real-time qualification and quantification of compounds in gas samples with trace level concentrations. In the detection process, neutral compounds-mainly volatile organic compounds-are ionized via chemical ionization with ionic reagents or primary ions. The most common reagent ions are H₃ O⁺ , NO⁺ and O₂ ^+• . While ionization with H₃ O⁺ occurs by means of proton transfer, the ionization via NO⁺ and O₂ ^+• offers a larger variety on ionization pathways, as charge transfer, hydride abstraction and so on are possible. The distribution of the reactant into various reaction channels depends not only on the usage of either NO⁺ or O₂ ^+• , but also on the class of analyte compounds. Furthermore, the choice of the reaction conditions as well as the choice of either SIFT-MS or PTR+SRI-MS might have a large impact on the resulting products. Therefore, an overview of both NO⁺ and O₂ ^+• as reagent ions is given, showing differences between SIFT-MS and PTR+SRI-MS as used analytical methods revealing the potential how the knowledge obtained with H₃ O⁺ for different classes of compounds can be extended with the usage of NO⁺ and O₂ ^+• .

Detection of Volatile Toxic Industrial Chemicals with Classical Ion Mobility Spectrometry and High-Kinetic Energy Ion Mobility Spectrometry

Due to their high sensitivity and compact design, ion mobility spectrometers are widely used to detect toxic industrial chemicals (TICs) in air. However, when analyzing complex gas mixtures, classical ion mobility spectrometry (IMS) suffers from false-positive rates due to limited resolving power or false-negative rates caused by competitive ion-molecule reactions and the resulting suppression of certain analyte ions. To overcome these limitations, high-kinetic energy IMS (HiKE-IMS) was introduced some years ago. In contrast to classical IMS, HiKE-IMS is operated at decreased pressures of 20···60 mbar and high reduced electric field strengths E/N of up to 120 Td. Under these conditions, the influence of competitive ion-molecule reactions on the prevailing ion population should be less pronounced, thus reducing false negatives. Additionally, effects such as fragmentation and field-dependent ion mobility may help to reduce false positives. In this work, the capabilities and limitations of HiKE-IMS in the field of on-site detection of the volatile TICs NH₃, HCN, H₂S, HCl, NO₂, Cl₂, and SO₂ are evaluated for the first time. Based on the limits of detection and the extent of spectral and chemical cross-sensitivities in gas mixtures, the results obtained for HiKE-IMS are compared with those obtained for classical IMS. It is shown that HiKE-IMS is less sensitive in comparison to classical IMS. However, when used for TIC detection, the reduced sensitivity of HiKE-IMS is not a major drawback. With values around 1 ppm_v, the achievable limits of detection for almost all TICs are below the AEGL-2 (4h) levels. Furthermore, in comparison to classical IMS, it is still striking that HiKE-IMS shows significantly less spectral and chemical cross-sensitivities and thus exhibits considerably lower false-positive and false-negative rates. Overall, it thus turns out that HiKE-IMS is a promising alternative to classical IMS in the field of on-site detection of TICs.

Selected Ion Flow Tube-Mass Spectrometry (SIFT-MS) as an Alternative to Gas Chromatography/Mass Spectrometry (GC/MS) for the Analysis of Cyclohexanone and Cyclohexanol in Plasma

Self-poisoning with professional agricultural pesticide products is responsible for about 20% of global suicide, with most cases occurring in South Asia and China. Treatment of severe poisoning involves long-term intensive clinical care and is often unsuccessful. Solvent co-formulants (such as cyclohexanone) also contribute to mortality themselves or via more toxic metabolic products (such as cyclohexanol). Faster detection of co-formulants could aid earlier identification of pesticide poisoning and faster intervention, reducing mortality. Conventional analysis of volatiles in blood uses headspace (HS)-GC/MS. This paper evaluates SIFT-MS, a direct MS technique that provides higher sample throughput than GC/MS, as a potential tool for cyclohexanone and cyclohexanol analysis in plasma. Both instruments were calibrated using a conventional approach prior to analysis of each porcine plasma sample on both instruments. Comparative data were evaluated using Bland-Altman plots, demonstrating that the techniques were in good agreement. Compared with GC/MS, SIFT-MS provides fourfold higher sample throughput and shows great promise as an alternative analytical tool.

Standard Validation Protocol for Selected Ion Flow Tube Mass Spectrometry Methods Applied to Direct Headspace Analysis of Aqueous Volatile Organic Compounds

Analysis of volatile organic compounds (VOCs) in water is conventionally conducted using gas chromatography (GC)-based methods, for which sample preparation demands are relatively high and throughput is relatively low due to the time taken to achieve chromatographic separation. Direct mass spectrometry (DMS) techniques such as selected ion flow tube mass spectrometry (SIFT-MS) have potential to analyze water headspace (HS) at high sensitivity with minimal sample preparation, eliminating preconcentration/purging and/or water management steps. However, the dearth of guidance for validation of DMS methods is an impediment to their adoption in routine analysis. This study applies and adapts an internationally recognized pharmaceutical industry guidance document for method validation to a prototypical SIFT-MS headspace analysis method for 17 toxic VOCs in water. The approach to validation is, however, applicable to any routine analysis conducted using SIFT-MS, and very likely to any methods developed using other DMS techniques. For the method developed and validated here, linearities (as measured by the linear regression coefficient, R²) were better than 0.990 for all compounds. Repeatability (measured using relative standard deviation, RSD) was less than 10% for all compounds. Similar method performance was observed for accuracy and recovery. The performance criteria achieved by this HS-SIFT-MS method suggest it has potential application in environmental and pharmaceutical routine analyses, perhaps as a rapid screening tool.

Understanding Gas Phase Ion Chemistry Is the Key to Reliable Selected Ion Flow Tube-Mass Spectrometry Analyses

Ion-molecule reactions (IMR) are at the very core of trace gas analyses in modern chemical ionization (CI) mass spectrometer instruments, which are increasingly being used in diverse areas of research and industry. The focus of this Perspective is on the ion chemistry that underpins gas-phase analytical CI methods. Special attention is given to the soft chemical ionization method known as selected ion flow tube-mass spectrometry (SIFT-MS). The processes involved in the ion chemistry of the reagent cations, H₃O⁺, NO⁺, and O₂^+•, and the anions, O^-•, O₂^-•, OH^-, and NO₂^-, are discussed in some detail. Stressed throughout is that an understanding of these processes is mandatory to obtain reliable analyses of humid gaseous media such as ambient air and exhaled breath. It is indicated that further research is needed to understand the consequences of replacing helium in some situations by the more readily available nitrogen as the carrier gas in SIFT-MS.

Accurate and rapid discrimination of cigarette and household decoration material ash residues by negative chemical ionization TOFMS via acid-enhanced evaporation

The detection and identification of cigarette ash in fire debris can be meaningful in fire investigations caused by burning cigarettes. In this work, a novel analytical method based on negative chemical ionization time-of-flight mass spectrometry (NCI/TOFMS) combined with a phosphoric-acid-enhanced evaporation strategy has been developed for the discrimination of cigarette ash samples (CAs) and common household decoration material ash samples (CHDMAs). A series of characteristic ions representing the acidified products HNCO and formic acid in the CAs were achieved, whose signal responses were enhanced with the help of mechanical agitation operation. To account for both the signal responses of the characteristic ions and acid corrosion of the ion source, the dynamic-purge gas was chosen to be 200 mL/min. The whole time for analysis was only 5 min, which is suitable for high-throughput measurements of large quantities of fire debris. As a result, a preliminary discrimination was achieved between the CAs and CHDMAs by virtue of the chemometric tool of principal components analysis (PCA) based on intensity differences of the characteristic ions. The results are encouraging and highlight the potential of NCI/TOFMS without complicated sample preparation steps for the accurate and high-throughput identification of cigarette ash on substrates in fire debris.

Highly selective and sensitive online measurement of trace exhaled HCN by acetone-assisted negative photoionization time-of-flight mass spectrometry with in-source CID

Exhaled hydrogen cyanide (HCN) has been extensively investigated as a promising biomarker of the presence of Pseudomonas aeruginosa in the airways of patients with cystic fibrosis (CF) disease. Its concentration profile for exhalation can provide useful information for medical disease diagnosis and therapeutic procedures. However, the complexity of breath gas, like high humidity, carbon dioxide (CO₂) and trace organic compounds, usually leads to quantitative error, poor selectivity and sensitivity for HCN with some of existing analytical techniques. In this work, acetone-assisted negative photoionization (AANP) based on a vacuum ultraviolet (VUV) lamp with a time-of- flight mass spectrometer (AANP-TOFMS) was firstly proposed for online measurement of trace HCN in human breath. In-source collision-induced dissociation (CID) was adopted for sensitivity improvement and the signal response of the characteristic ion CN^- (m/z 26) was improved by about 24-fold. For accurate and reliable analysis of the exhaled HCN, matrix influences in the human breath including humidity and CO₂ were investigated, respectively. A Nafion tube was used for online dehumidification of breath samples. Matrix-adapted calibration in the concentration range of 0.5-50 ppbv with satisfactory dynamic linearity and repeatability was obtained. The limit of quantitation (LOQ) for HCN at 0.5 ppbv was achieved in the presence of 100% relative humidity and 4% CO₂. Finally, the method was successfully applied for online determination of human mouth- and nose-exhaled HCN, and the nose-exhaled HCN were proved to be reliable for assessing systemic HCN levels for individuals. The results are encouraging and highlight the potential of AANP-TOFMS with in-source CID as a selective, accurate, sensitive and noninvasive technique for determination of the exhaled HCN for CF clinical diagnosis and HCN poisoning assessment.

Ozone Quantification by Selected Ion Flow Tube Mass Spectrometry: Influence of Humidity and Manufacturing Gas of Ozone Generator

The quantification of ozone by SIFT-MS was investigated in conditions suitable with an industrial emission context (high ozone demand, dry air/oxygen as the manufacturing gas of the ozone generator, and high humidity levels beyond saturation at room conditions). Ozone reacts with four negative precursor ions available in the SIFT-MS device (NO₂^-, O₂^-, HO^-, and O^-), each precursor ion having its specific domain of linearity. For a high ozone concentration range, only NO₂^- and O₂^- have resulted in a linear behavior (between 1 and 100 ppmv of O₃ for NO₂^-, between 1 and 50 ppmv of O₃ for O₂^-). No water interference was identified during ozone measurements by SIFT-MS using NO₂^- and O₂^- precursor ions, even with extreme humidity levels. The presence of nitrogen oxide contaminants (due to the use of dry air as the manufacturing gas of the ozone generator) affected the ozone quantification by SIFT-MS. It is critical for NO₂^- precursor ions, whose rate constant varied as a function of NO₂ concentrations. With O₂^- precursor ion, ozone was successfully measured in the presence of nitrogen oxides; however, the secondary chemistry must be taken into account.

Real-time differentiation of ethylbenzene and the xylenes using selected ion flow tube mass spectrometry

RATIONALE

Monitoring of isomeric analytes using mass spectrometry usually requires a time-consuming chromatographic separation of the analytes before analysis. Selected ion flow tube mass spectrometry (SIFT-MS) can provide rapid direct analysis of ethylbenzene and xylene by utilizing the different reaction chemistry of the isomers. O₂ ⁺ yields the same product ions from each isomer but in different ratios. OH^- yields different product ions.

METHODS

The reaction chemistry of C₈ H₁₀ with the reagent ion OH^- generated from a microwave discharge of moist air in a commercial SIFT-MS instrument was utilized in this study. The product ion from OH^- yielded ions at different masses for each isomer. To gain an understanding of how the product ion from ethylbenzene of HO₂ ^- was generated, a theoretical study of the potential reaction surface was undertaken that accounted for the experimental observations.

RESULTS

Measurements of OH^- with ethylbenzene showed the product ion to be HO₂ ^- at m/z 33. The reaction of OH^- with xylene yielded the major product ion at m/z 105, C₈ H₉ ^- . HO₂ ^- also underwent a slow secondary reaction with CO₂ and O₂ present from air in the samples. These findings were supported by calculations of the potential energy surface for the reactions. Measurements made on a certified gas mixture of ethylbenzene and xylene in the concentration range up to 5000 ppbv gave a linear response for each analyte.

CONCLUSIONS

A fast, efficient method was developed for monitoring xylene and ethylbenzene in a mixture without the need for chromatographic separation before analysis using SIFT-MS.

Direct analysis of aldehydes and carboxylic acids in the gas phase by negative ionization selected ion flow tube mass spectrometry: Quantification and modelling of ion-molecule reactions

RATIONALE

The concentrations of aldehydes and volatile fatty acids have to be controlled because of their potential harmfulness in indoor air or relationship with the organoleptic properties of agri-food products. Although several specific analytical methods are currently used, the simultaneous analysis of these compounds in a complex matrix remains a challenge. The combination of positive and negative ionization selected ion flow tube mass spectrometry (SIFT-MS) allows the accurate, sensitive and high-frequency analysis of complex gas mixtures of these compounds.

METHODS

The ion-molecule reactions of negative precursor ions (OH^- , O^•- , O₂ ^•- , NO₂ ^- and NO₃ ^- ) with five aldehydes and four carboxylic acids were investigated in order to provide product ions and rate constants for the quantification of these compounds by negative ion SIFT-MS. The results were compared with those obtained by conventional analysis methods and/or with already implemented SIFT-MS positive ionization methods. The modelling of hydroxide ion (OH^- )/molecule reaction paths by ab-initio calculation allowed a better understanding of these gas-phase reactions.

RESULTS

Deprotonation systematically occurs by reaction between negative ions and aldehydes or acids, leading to the formation of [M - H]^- primary ions. Ab-initio calculations demonstrated the α-CH deprotonation of aldehydes and the acidic proton abstraction for fatty acids. For aldehydes, the presence of water in the flow tube leads to the formation of hydrated ions, [M - H]^- .H₂ O. With the NO₂ ^- precursor ion, a second reaction channel results in ion-molecule association with the formation of M.NO₂ ^- ions.

CONCLUSIONS

Except for formaldehyde, all the studied compounds can be quantified by negative ion SIFT-MS with significant rate constants. In addition to positive ion SIFT-MS with H₃ O⁺ , O₂ ⁺ and NO⁺ precursor ions, negative ionization with O^•- , O₂ ^•- , OH^- , NO₂ ^- and NO₃ ^- extends the range of analysis of aldehydes and carboxylic acids in air without a preparation or separation step. This methodology was illustrated by the simultaneous quantification in single-scan experiments of seven aldehydes and six carboxylic acids released by building materials.

Aldehydes gas ozonation monitoring: Interest of SIFT/MS versus GC/FID

Two analytical techniques - online Gas Chromatography coupled with Flame Ionization Detector (often used method for VOCs monitoring) versus Selected Ion Flow Tube coupled with Mass Spectrometry (a more recent technique based on direct mass spectrometry) - were compared in association to an ozone-based gas treatment. Selecting aldehydes as the representative VOCs, their concentrations were monitored during ozonation experiments by both techniques in parallel. Contradictory results were obtained in the presence of ozone. Aldehydes were up to 90% removed due to a reaction with ozone according to GC/FID analysis, whereas with SIFT/MS, aldehydes concentration remained at the same level during the experiments regardless of the ozone presence. In addition, it was demonstrated that the apparent aldehydes removal was affected by GC injector temperature, varying from 90% (when it was at 250 °C) to 60% (at 100 °C). Meanwhile, even when the ozonation reactor was heated to 100 °C, no aldehydes conversion was evidenced by SIFT/MS, suggesting that the GC injector temperature was not the only interference-causing parameter. The ozone-aldehyde reaction is probably catalyzed by some material of GC injector and/or column. An ozone-GC interference was therefore confirmed, making unsuitable the use of GC/FID with silicone stationary phase to monitor aldehydes in presence of high concentrations of ozone (at least 50 ppmv). On the other hand, SIFT/MS was validated as a reliable technique, which can be employed in order to measure VOCs concentrations in ozonation processes.

Evolution of clinical and environmental health applications of exhaled breath research: Review of methods and instrumentation for gas-phase, condensate, and aerosols

Human breath, along with urine and blood, has long been one of the three major biological media for assessing human health and environmental exposure. In fact, the detection of odor on human breath, as described by Hippocrates in 400 BC, is considered the first analytical health assessment tool. Although less common in comparison to contemporary bio-fluids analyses, breath has become an attractive diagnostic medium as sampling is non-invasive, unlimited in timing and volume, and does not require clinical personnel. Exhaled breath, exhaled breath condensate (EBC), and exhaled breath aerosol (EBA) are different types of breath matrices used to assess human health and disease state. Over the past 20 years, breath research has made many advances in assessing health state, overcoming many of its initial challenges related to sampling and analysis. The wide variety of sampling techniques and collection devices that have been developed for these media are discussed herein. The different types of sensors and mass spectrometry instruments currently available for breath analysis are evaluated as well as emerging breath research topics, such as cytokines, security and airport surveillance, cellular respiration, and canine olfaction.

Gas Analysis by Electron Ionization Combined with Chemical Ionization in a Compact FTICR Mass Spectrometer

In this Article, a compact Fourier transform ion cyclotron resonance (FTICR) mass spectrometer based on a permanent magnet is presented. This instrument has been developed for real-time analysis of gas emissions. The instrument is well-suited to industrial applications or analysis of toxic and complex samples where the concentrations can vary rapidly on a wide range. The novelty of this instrument is the ability to use either electron ionization (EI) or chemical ionization (CI) individually or both of them alternatively. Also in CI mode, different precursor ions can be used alternatively. Volatile organic compounds (VOCs) from the ppb level to very high concentrations (% level) can be detected by CI or EI. The magnet is composed of three Halbach arrays, and the nominal field achieved is 1.5 T. The ICR cell is a 3 cm side length cubic cell. The mass range is 12-200 u with a broad band detection. The mass accuracy of 0.005 u and the resolving power allow the separation of isobaric ions such as C₃H₈⁺ and CO₂⁺. Gas introduction via controlled gas pulses, electron ionization, ion-molecule reactions, ion selection, and detection are all performed in the ICR cell. The potential of the instrument will be illustrated by an analysis of a gas mixture containing trace components at ppm level (VOCs) and components in the 0.5-100% range (N₂, alkanes, and CO₂).

Detection of gas traces using semiconductor sensors, ion mobility spectrometry, and mass spectrometry

This article deals with the state-of-the-art instrumentation and application in the field of solid state gas sensorics, ion mobility spectrometry and mass-spectrometry-related research for the detection and measurements of low gas and vapor concentrations. The advantages and disadvantages of gas-analytical devices and systems are discussed, as well as the possibilities of its complex and/or complementary applications. Ion mobility spectrometry-mass spectrometry and subsequent techniques based on solid-state gas sensors are proposed for planned medical study.

Ion chemistry at elevated ion–molecule interaction energies in a selected ion flow-drift tube: reactions of H3O+, NO+ and O2+ with saturated aliphatic ketones

Rate coefficients and product ion branching ratios determined for proton transfer, association and charge transfer reactions provide insight into reaction mechanisms.