The Influence of Custom-Milled Framework Design for an Implant-Supported Full-Arch Fixed Dental Prosthesis: 3D-FEA Sudy

Ranking Technologies of Additive Manufacturing of Removable Complete Dentures by the Results of Their Mechanical Testing

In this study, a methodology was developed for ranking manufacturing technologies of removable complete dentures (RCDs) according to the results of their full-scale mechanical tests. The actuality of the study is motivated by establishing the advantages and drawbacks of 3D-printed RCDs in contrast with ones manufactured via an analog protocol. The RCDs were fabricated via four technological routes that included various combinations of subtractive technologies (hot polymerization/HP and CAD/CAM milling) and additive manufacturing (digital light processing/DLP) ones and the installation of commercially available cosmetic denture teeth (DT). In the mechanical tests, different blocks of teeth (incisors, canines, premolars and molars) were loaded. To solve the ranking problem, it was proposed to interpret the results of the mechanical tests in terms of the reliability, durability and compliance/stiffness criteria. For this purpose, the combined AHP-VIKOR method was applied. In addition, a computer simulation of the mechanical loading conditions and the response of the RCDs was performed based on the finite element method (FEM). As the key conclusion, it was stated that additive manufacturing (AM) methods are competitive and cost-effective techniques for the fabrication of RCDs.

A Nonlinear Three-Dimensional Finite Element Analysis of Stress Distribution and Microstrain Evaluation in Short Dental Implants with Three Different Implant-Abutment Connections in Single and Splinted Conditions in the Posterior Mandible

Background

Stress distribution plays a vital role in the longevity and success of implant-supported prosthesis. This study evaluated the von Mises stress and microstrain in the peri-implant bone and the implant-abutment junction of short dental implants with three different implant-abutment connections in splinted and unsplinted conditions using finite element analysis (FEA).

Materials and Methods

In this experimental study, nine transversely isotropic finite element models were developed, and randomly divided into three equal groups (n = 3): control, (Group AC) single-standard 4.3 × 10 mm bone level implant-supported restorations with external hexagonal (EH) connection, internal conical (IC) and internal trichannel (ITC) connection, single short implant-supported restorations (Group AT), and splinted short implant-supported restorations (Group B) for each of the three implant-abutment connections, respectively. A 200 N load was applied along the long axis of the implants and a 100 N (45°) oblique load was applied and von Mises stress and microstrain values were evaluated.

Results

Single standard implants demonstrated the highest von Mises stress and microstrain values followed by single short implants and splinted short implants, respectively. Among the implant-abutment connections, the IC connection showed the highest values and the ITC connection showed the least values.

Conclusion

Within the limitations of this study, it was concluded that splinting of short dental implants demonstrated lesser and more homogeneous stress and microstrain, especially on oblique loading. The microstrain values for all connections evaluated were within the physiological loading limit (200-2,500 N) and were hence considered safe for clinical use.

Biomechanical behavior analysis of four types of short implants with different placement depths using the finite element method

STATEMENT OF PROBLEM

The clinical application of short implants has been increasing. However, studies on the marginal bone loss of short implants are sparse, and clinicians often choose short implants based on their own experience rather than on scientific information.

PURPOSE

The purpose of this finite element analysis study was to evaluate the microstrain-stress distribution in the peri-implant bone and implant components for 4 types of short implants at different placement depths of platform switching.

MATERIAL AND METHODS

By using short implants as prototypes, 4 short implant models were 1:1 modeled. The diameter and length of the implants were 5×5, 5×6, 6×5, and 6×6 mm. The restoration was identical for all implants. Three different depths of implant platform switching were set: equicrestal, 0.5-mm subcrestal, and 1-mm subcrestal. The models were then assembled and assigned an occlusal force of 200 N (vertical or 30-degree oblique). A finite element analysis was carried out to evaluate the maximum equivalent elastic strain and von Mises stress in the bone and the stress distribution in the implant components.

RESULTS

The 5×5 implant group showed the largest intraosseous strain (21.921×10³ με). A 1-mm increase in implant diameter resulted in a 17.1% to 37.4% reduction in maximum intraosseous strain when loaded with oblique forces. The strain in the bone tended to be much smaller than the placement depth at the equicrestal and 0.5-mm subcrestal positions than that at the 1-mm subcrestal position, especially under oblique force loading, with an increase of approximately 37.4% to 81.8%. In addition, when the cortical bone thickness was less than 4 mm, 5×6 implants caused significantly higher intraosseous stresses than 6×6 implants.

CONCLUSIONS

Large implant diameters, rather than long implants, led to reduced intraosseous strain, especially under oblique loading. Regarding the implant platform switching depth, the short implant showed small intraosseous strains when the platform switching depth was equicrestal or 0.5-mm subcrestal.

Fracture resistance of Ceramic-Polymer hybrid materials using microscopic finite element analysis and experimental validation

The objective of this paper is to elucidate the response to contact stresses of Polymer Infiltrated Ceramic Network (PICN) using the microscopic viscoplastic finite elements, validated by clinically relevant in vitro tests. A feldspathic ceramic material, namely Vita Mark II, is an interconnected structure infiltrated with the polymer (PMMA). Axisymmetric finite element microstructure models are reconstructed from two-dimensional images of a PICN microstructure. Viscoplastic finite element analysis (FEA) with various degrees of microscopic damages occurring over contact is performed. The force-displacement responses obtained from FEA are validated with Hertzian contact tests. Finite element results for force-displacement, stresses and strains in each phase are discussed. We hypothesize that the resistance to fracture of PICN can be further improved by microstructural tailoring. The experimental evidence suggests that a composite material is both more resistant to displacement under load and more resistant to crack initiation and propagation, as hypothesized. Further parametric study on the effects of various volume fractions of two phases in PICN is done to provide some insight on increased contact damage resistance of PICN as well as potential optimization of microstructures.

Algorithm for Designing a Removable Complete Denture (RCD) Based on the FEM Analysis of Its Service Life

(1) Background: The paper addresses the computer simulation and prediction of the service life of the base of removable complete dentures (RCDs) under typical loads caused by biting and chewing food. For this purpose, the finite element method (FEM) was used. It is assumed that various blocks of teeth, such as incisors, canines, premolars and molars, are subjected to cyclic impacts during a human life. (2) Methods: Both symmetric and asymmetric mastication (two- and one-sided loads, respectively) cases were considered. The load level was assumed to be 100 N, which corresponds to the average muscular compression force of typical human jaws. (3) Results: The FEM analysis of the stress-strain state evolution for RCDs under cyclic loads was carried out. Maps of equivalent lines were drawn for the denture base in terms of its durability. A multi-axial criterion was implemented to determine the number of cycles prior to failure by the mechanism of a normal opening mode crack. The FEM-based assessment of the service life of RCDs enabled us to establish the critical stress concentration areas, thereby allowing for further planning for the correction of an occlusal scheme or teeth inclinations. As a result, the service life of RCDs under cyclic loading can be improved. (4) Conclusions: An algorithm for designing RCDs in the case of edentulism based on the FEM simulation using commercial software as part of the procedure is proposed.

In Vivo Analysis of Intraoral Scanner Precision Using Open-Source 3D Software

Intraoral three-dimensional scanning techniques could be used to improve dental practice, leading to an improved overall quality of the prosthetic devices and improved comfort for the patient. An accurate and precise intraoral scanner allows proper diagnosis, follow-up evaluation, and prosthesis application. The aim of this research is to evaluate the precision of an intraoral scanners (Medit i500, Medit Corp., Seoul, Korea), using open-source software in the digital workflow. The precision was compared through repetitions of the scanning process of the upper dental arch, following superimpositions in the whole 3D arch area. It was possible to display colorimetric maps for qualitative comparison, and the deviations of the values were classified as clinically acceptable. Within the limitation of this study, the clinically acceptable in vivo frequency of points’ deviation, or the precision, was obtained in 98.8% ± 1.4%; therefore, the use of open-source software can be a viable option in the digital workflow, improving patient follow ups with the 3D model superimposition.

Stress Distribution Pattern in Zygomatic Implants Supporting Different Superstructure Materials

The aim of this study was to assess and compare the stress–strain pattern of zygomatic dental implants supporting different superstructures using 3D finite element analysis (FEA). A model of a tridimensional edentulous maxilla with four dental implants was designed using the computer-aided design (CAD) software. Two standard and two zygomatic implants were positioned to support the U-shaped bar superstructure. In the computer-aided engineering (CAE) software, different materials have been simulated for the superstructure: cobalt–chrome (CoCr) alloy, titanium alloy (Ti), zirconia (Zr), carbon-fiber polymers (CF) and polyetheretherketone (PEEK). An axial load of 500 N was applied in the posterior regions near the zygomatic implants. Considering the mechanical response of the bone tissue, all superstructure materials resulted in homogeneous strain and thus could reconstruct the edentulous maxilla. However, with the aim to reduce the stress in the zygomatic implants and prosthetic screws, stiffer materials, such Zr, CoCr and Ti, appeared to be a preferable option.

Comparison of Two Types of Preparation for Laminate Veneer with Three Types of All-Ceramic Materials

OBJECTIVE

 The objective of this study was to compare types of veneer preparations and their combination with three materials.

MATERIALS AND METHODS

 Two finite element models were specially prepared used representing window and wrap around preparation for veneers. The "central incisor" tooth geometry was acquired using a laser scanner, and then its surface was adjusted to form a solid model prior to the removal of each preparation separately. Three materials (Lava Ultimate, IPS e-max, and Celtra) were tested in combination with the preparation type. Bone geometry was simplified as two coaxial cylinders in all models. Each model was subjected to two loading conditions of occlusion (edge-to-edge bite and normal bite).

STATISTICAL ANALYSIS AND RESULTS

 It was observed that cortical, cancellous bone, and periodontal ligament are insensitive to preparation or materials. Their stresses and deformation were within physiological limits. Significant changes appeared on the central incisor tooth structure, cement layer, and veneer layer stresses and deformations under loading cases.

CONCLUSIONS

 Edge-to-edge bite stresses are severe with window-type preparation, and normal bite did not show any critical values on tooth structure, cement layer, or veneer layer. Veneer layer finish line and its contact with the cement layer and tooth structure play a role in the loading transfer mechanism. Preparation type alters the values of stresses on tooth structure, cement, and veneer layers. With window preparation, extreme stresses appear at finish line, while stresses appear under the loading site with wrap around preparation. Veneer and cement layers withstand the load energy with wrap around preparation and reduce tooth structure stresses. Thus, the lifetime of veneer and cement layers might be longer with window preparation.

Final Colour of Ultratranslucent Multilayered Zirconia Veneers, Effect of Thickness, and Resin Cement Shade

Background

Aesthetic restorations should be able to mimic the natural colour depth of teeth, affected by several factors including material properties. There is a lack of information regarding the effect of cement shade and material thickness on the final colour of ultratranslucent multilayered zirconia veneers.

Objectives

This study evaluated the effect of ceramic thickness and resin cement shade on the final colour of different layers of ultratranslucent multilayered (UTML) zirconia veneers.

Methods

This in vitro study produced 90 rectangular-shaped specimens with nonsintered Katana UTML monolithic zirconia (Kuraray Noritake Dental, Tokyo, Japan), shade A1 blocks. Ceramic samples were prepared in two groups of 0.7 mm and 0.5 mm thicknesses, 45 of each (a: 8 × 11 × 0.5 mm; b: 8 × 11 × 0.7 mm). Specimens of each thickness were further divided into 5 groups: universal, clear, brown, white, and opaque (n = 9). Each adhesive resin cement (Panavia V5) was applied between the ceramic samples and composite substrate. The colour values were measured using a spectrophotometer in baseline and after resin cement application according to the CIELab system. For all samples, ΔE00 values were obtained. Data were evaluated with SPSS 25 using the three-way ANOVA test (p < 0.05).

Results

The factors of cement shade, ceramic thickness, and ceramic layers have statistically significant effect on ΔE00 values (p < 0.001). The results showed lower ΔE00 values with thicker ceramic veneers. Tukey test results showed that the opaque and brown shade had a significantly greater ΔE00 values comparing to universal (p = 0.004), clear, and white shades (p < 0.001).

Conclusion

The colour change was greater in lower ceramic thickness. Different shades of resin cement and layers of UTML zirconia differently affected the final colour.

Effect of erosive media on microhardness and fracture toughness of CAD-CAM dental materials

Background

Erosive acids might create surface flaws and deteriorate the mechanical properties of CAD-CAM materials. This invitro study aimed to investigate the effect of simulated gastric HCl and extrinsic erosive acids on surface microhardness and fracture toughness of CAD-CAM materials.

Methods

400 bar-shaped specimens (17×4×2 mm³) were prepared from 4 different CAD-CAM dental materials (n = 100/group); monolithic zirconia (Ceramill Zolid HT+, Amanngirbach, Austria), lithium disilicate ceramic (IPS e.max CAD, Ivoclar Vivadent, Liechtenstein), nanohybrid resin composite (Grandio Blocs, VOCO) and polymer-infiltrated glass network (Vita Enamic, VITA Zahnfabrik). Specimens from each material type were further subdivided into 5 groups (n = 20) according to the erosive media applied (simulated gastric HCl, white wine, Coca-Cola®, orange juice, and artificial saliva that served as a control). Specimens were immersed for 24 h in an incubator at 37 ℃, then ultrasonically cleaned in distilled water and air-dried. Half of the specimens were tested for Vickers microhardness (VHN) at parameters of 500 gf for 10 s, while the rest of the specimens underwent 3-point flexure till fracture. Fractured surfaces were examined under a scanning electron microscope (SEM) for fracture toughness (K_IC) calculation using the quantitative fractographic analysis method. Data collected were statistically analyzed using two-way analysis of variance (α = 0.05) after verification of data normality and homogeneity of variances.

Results

Erosive media created surface flaws that lowered the surface microhardness of the material and initiated the fracture pattern under different loads according to material type. The material type was a more predominant factor than erosive media that affected either the microhardness or the fracture toughness of CAD-CAM dental materials. The highest VHN and K_IC values were found among Ceramill Zolid HT+ groups followed by IPS e.max CAD and Grandio Blocs regardless of the erosive media employed. Erosive media significantly reduced the VHN and K_IC in Vita Enamic specimens compared to the rest of the material types.

Conclusion

All CAD-CAM materials used, except Vita Enamic, showed high resistance against the erosive acids indicating higher longevity of the material in patients frequently exposed to either extrinsic or intrinsic acid.

A Dual Discriminator Adversarial Learning Approach for Dental Occlusal Surface Reconstruction

Objective. Restoring the correct masticatory function of partially edentulous patient is a challenging task primarily due to the complex tooth morphology between individuals. Although some deep learning-based approaches have been proposed for dental restorations, most of them do not consider the influence of dental biological characteristics for the occlusal surface reconstruction. Description. In this article, we propose a novel dual discriminator adversarial learning network to address these challenges. In particular, this network architecture integrates two models: a dilated convolutional-based generative model and a dual global-local discriminative model. While the generative model adopts dilated convolution layers to generate a feature representation that preserves clear tissue structure, the dual discriminative model makes use of two discriminators to jointly distinguish whether the input is real or fake. While the global discriminator focuses on the missing teeth and adjacent teeth to assess whether it is coherent as a whole, the local discriminator aims only at the defective teeth to ensure the local consistency of the generated dental crown. Results. Experiments on 1000 real-world patient dental samples demonstrate the effectiveness of our method. For quantitative comparison, the image quality metrics are used to measure the similarity of the generated occlusal surface, and the root mean square between the generated result and the target crown calculated by our method is 0.114 mm. In qualitative analysis, the proposed approach can generate more reasonable dental biological morphology. Conclusion. The results demonstrate that our method significantly outperforms the state-of-the-art methods in occlusal surface reconstruction. Importantly, the designed occlusal surface has enough anatomical morphology of natural teeth and superior clinical application value.

Mechanical Behavior of Alkasite Posterior Restorations in Comparison to Polymeric Materials: A 3D-FEA Study

The present investigation evaluated the effect of the combination of different dental filling materials in Class I cavities under occlusal loading using three-dimensional finite elements analysis (FEA). Six computer-generated and restored models of a lower molar were created in the CAD software and compared according to the biomechanical response during chewing load condition. Two adhesively bonded bulk restorative materials [bulk-fill resin composite (BF) or Alkasite (Alk)] were evaluated with or without the presence of a base material below (flowable resin composite or glass ionomer cement). A food bolus was placed on the occlusal surface mimicking the compressive occlusal load (600 N) during the static linear analysis. The maximum principal stress (tensile) was calculated as stress criteria in enamel, dentin and restoration. All models showed high stresses along the enamel/restoration margin with a similar stress trend for models restored with the same upper-layer material. Stress values up to 12.04 MPa (Alk) or up to 11.12 MPa (BF) were recorded at the enamel margins. The use of flexible polymeric or ionic base material in combination with bulk-fill resin composite or Alk did not reduce the stress magnitude in dentine and enamel. Class I cavities adhesively restored with bulk-fill resin composite showed lighter stress concentration as well as Alk. Therefore, adhesively bonded Alk restoration showed a promising mechanical behavior when used with different base materials or as a bulk restoration for posterior Class I cavity.

Esthetic Assessment following Ridge Augmentation, Late Implant Placement and Immediate Esthetic Reconstruction of the Atrophic Anterior Maxilla

Purpose: Evaluate the esthetic outcome of ridge augmentation using cancellous bone-block allografts, late implant placement, and immediate loading in the atrophic anterior maxilla, by PES (pink esthetic score) and WES (white esthetic score) indexes. Materials and Methods: Retrospective cohort study. Inclusion criteria were bone loss of at least 3 mm horizontally and 3 mm vertically according to preliminary CBCT; ridge augmentation using cancellous bone-block allografts; six months later the implant insertion and immediately loaded. PES-WES index was used for esthetic assessment of soft tissues surrounding the final implant-supported prosthesis (ISP). Results: All twenty-five successive individuals were included. The mean follow-up was 12.1 ± 56 months (range, 42−90 months). The mean PES index and WES index were 7 ± 1.74 (range: 5−10) and 8.4 ± 2.12 (range: 5−10), respectively. The mean total combination of PES index and WES index (PES/WES) was 15.3 ± 2.85 (range: 12−20). All ISPs had an overall score >12 (the defined threshold of clinical acceptability). Conclusions: Ridge augmentation in the atrophic anterior maxilla using cancellous bone-block allografts and immediate loading allows a stable esthetic result of the soft and hard tissues over the years (follow-up of 42−90 months).

Numerical analysis of WaveOne Gold and 2Shape endodontic files during root canal treatment

This study aims to develop and analyse a finite element model of the endodontic nickel-titanium (NiTi) instrument during the root canal treatment (RCT). The 3D model of the tooth and the endodontic instrument has been created using computer-aided design software. The nonlinear explicit dynamic analysis in the CAE package (ANSYS) has been used to analyse the mechanical behaviour of endodontic instruments such as total deformation, equivalent elastic strain, and equivalent stress during canal preparation. The mechanical behaviour of three commercially available endodontic NiTi alloy instruments such as WaveOne Gold (WOG), 2Shape 1 (TS1) and 2Shape 2 (TS2) endodontic files was evaluated using FEA. Consequently, the effect of deformation, equivalent stress and equivalent elastic strain on endodontic files during cleaning and shaping are investigated and compared. The results show that the total deformation and equivalent elastic strain are maximum in the TS1 endodontic file in comparison to TS2 and WOG files.

Influence of Bone-Level Dental Implants Placement and of Cortical Thickness on Osseointegration: In Silico and In Vivo Analyses

The purpose of this research is to study the biomechanical response of dental implants in bone-level type locations, 0.5 mm above and below the bone level. In addition, the influence of the thickness of the cortical bone on osseointegration is determined due to the mechanical loads transfer from the dental implant to the cortical and trabecular bone. The thicknesses studied were 1.5 mm and 2.5 mm. Numerical simulations were performed using a finite element method (FEM)-based model. In order to verify the FEM model, the in silico results were compared with the results obtained from a histological analysis performed in an in vivo study with 30 New Zealand rabbits. FEM was performed using a computerized 3D model of bone-level dental implants inserted in the lower jawbone with an applied axial load of 100 N. The analysis was performed using different distances from the bone level and different thicknesses of cortical bone. The interface area of bone growth was evaluated by analyzing the bone–implant contact (BIC), region of interest (ROI) and total bone area (BAT) parameters obtained through an in vivo histological process and analyzed by scanning electron microscopy (SEM). Bone-level implants were inserted in the rabbit tibiae, with two implants placed per tibia. These parameters were evaluated after three or six weeks of implantation. FEM studies showed that placements 0.5 mm below the bone level presented lower values of stress distribution compared to the other studied placements. The lower levels of mechanical stress were then correlated with the in vivo studies, showing that this position presented the highest BIC value after three or six weeks of implantation. In this placement, vertical bone growth could be observed up the bone level. The smallest thickness of the study showed a better transfer of mechanical loads, which leads to a better osseointegration. In silico and in vivo results both concluded that the implants placed 0.5 mm below the cortical bone and with lower thicknesses presented the best biomechanical and histological behavior in terms of new bone formation, enhanced mechanical stability and optimum osseointegration.

Effect of Different Ceramic Materials on Fatigue Resistance and Stress Distribution in Upper Canines with Palatal Veneers

OBJECTIVE

 The aim of this study was to evaluate, by means of a fatigue life test, different ceramic materials used in palatal veneers to restore the canine guidance.

MATERIALS AND METHODS

 Forty-five standardized anatomical preparations were made in extracted healthy human canines with 1.2 uniform thickness. Samples were scanned, restorations were designed and milled in polymer-infiltrated ceramic network (PICN, Vita Enamic), zirconia-reinforced lithium silicate (ZLS, Vita Suprinity), and high translucent yttrium oxide-stabilized tetragonal zirconia (YZHT, Vita YZHT). Dental preparations were etched, restorations were processed according to the manufacturers' recommendations, and adhesively cemented. Then, three samples of each group were tested with load-to-fracture to determine the fatigue parameters. In addition, the palatal veneers stresses were evaluated using numerical models through finite element analysis.

RESULTS

 The mean of the monotonic test for PICN, ZLS, and YZHT was 674.18 N, 560.5 N, and 918.98 N, respectively. The StepWise test was performed until specimen fracture or until suspension of the test after 1.2 × 10⁶ cycles. Regarding survival, using the Kaplan-Meier method, PICN presented results for the mean and median of 245.21 N and 225 N, respectively; ZLS had an average of 175.76 N and a median of 168 N, and YZHT with an average of 383.30 N and a median of 366 N. Regarding the Weibull method, PICN showed results of 5.43 β and 264 η for form and scale, respectively; ZLS had 36.14 β for form and 380.67 η for scale; and YZHT presented 4.95 β for form and 417.38 η for scale. The highest stress value was calculated for YZHT, ZLS, and PICN, respectively.

CONCLUSIONS

 It was possible to conclude that all tested materials have the possibility of being used for rehabilitation of upper canines' palatal surface.

Influence of different diameter reductions in the labial neck region on the stress distribution around custom-made root-analogue implants

This study was designed to investigate the influence of diameter reductions on the stress distribution around root-analogue implants via 3D finite element analysis. Four root-analogue implant models with different diameter reductions (0, 1, 2, or 3 mm), a traditional threaded implant and congruent bone models were created through reverse engineering. A 100-N force was applied parallel with and in a 45° angle to the implant axis, respectively. The stress concentration in the labial neck area around implants with 1-2 mm diameter reduction was lower than seen with no reduction. When the implant diameter was reduced by 3 mm, there were obvious stress concentrations in both implant and bone (the maximum stress was 206  and 111 MPa, respectively). In other groups, the maximum stress was 65.1 MPa in the bone and 108 MPa in the implant. Additionally, the stress concentration in the bone around the root-analogue implant when the implant diameter was reduced by 0-2 mm (maximum stress of 65.1 MPa) was obviously smaller than that around the traditional implant (maximum stress 130.4 MPa). Reducing the diameter of maxillary central incisor root-analogue implants by up to 2 mm next to the labial cortical bone could help disperse stress.

Finite element analysis and nanomechanical properties of composite and ceramic dental onlays

The aim is to evaluate the mechanical properties of the composite and ceramic based indirect restorative materials used in dental treatments with scanning nanoindentation test (NT). Finite element analysis (FEA) was applied to investigate the stress distribution. Four hybrid composite materials; Indirect resin composite (IRC), Resin nanoceramic (RNC), Polymer infiltrated ceramic (PIC) and Zirconia-reinforced lithium-di-silicate (ZRC) were divided into two subgroups for NT (n = 20) and fracture test (n = 40). Statistical analyses were performed with independent t-test, ANOVA and post-hoc Tukey tests (p ≤ 0.05). The highest hardness, elasticity and fracture toughness were observed in ZRC (p = 0.001). Frequency of vertical root fractures in RNC and IRC were statistically lower than ZRC (p = 0.032). Reinforced CAD-CAM ceramics revealed higher mechanical properties compared with IRC materials. The FEA model for fracture mechanism of RNC demonstrated lowest stress values and uniform stress distribution amongst all groups, while ZRC and PIC presented the highest fracture toughness.

Finite Element Analysis of Restored Principal Abutment in Free-End Saddle Partial Denture

PURPOSE

This study analyzed the stress distribution of restored principal abutments in free-end saddle partial dentures.

MATERIALS AND METHODS

The mandibular second premolar was modeled with class II cavity restored with composite resins (Tetric N Ceram and Charisma Smile). Finite element analysis (FEA) was used to examine the stresses under 200-N static load vertically and horizontally and the results were graphically illustrated in the form of von Mises stresses.

RESULTS

The von Mises stress distribution patterns of two different composite resins (Tetric N Ceram and Charisma Smile) were very similar in all modes of loading.

CONCLUSION

Composite resins with a similar modulus of elasticity in class II cavities with occlusal rest seat preparation had similar stress distributions.

CLINICAL SIGNIFICANCE

Nanohybrid composite resin restorations may be a possible method for preparing abutments for receiving elements of the removable partial denture (RPD).

Influence of Framework Material and Posterior Implant Angulation in Full-Arch All-on-4 Implant-Supported Prosthesis Stress Concentration

This study evaluated the influence of distal implants angulation and framework material in the stress concentration of an All-on-4 full-arch prosthesis. A full-arch implant-supported prosthesis 3D model was created with different distal implant angulations and cantilever arms (30° with 10-mm cantilever; 45° with 10-mm cantilever and 45° with 6-mm cantilever) and framework materials (Cobalt–chrome [CoCr alloy], Yttria-stabilized tetragonal zirconia polycrystal [Y-TZP] and polyetheretherketone [PEEK]). Each solid was imported to computer-aided engineering software, and tetrahedral elements formed the mesh. Material properties were assigned to each solid with isotropic and homogeneous behavior. The contacts were considered bonded. A vertical load of 200 N was applied in the distal region of the cantilever arm, and stress was evaluated in Von Misses (σVM) for prosthesis components and the Maximum (σMAX) and Minimum (σMIN) Principal Stresses for the bone. Distal implants angled in 45° with a 10-mm cantilever arm showed the highest stress concentration for all structures with higher stress magnitudes when the PEEK framework was considered. However, distal implants angled in 45° with a 6-mm cantilever arm showed promising mechanical responses with the lowest stress peaks. For the All-on-4 concept, a 45° distal implants angulation is only beneficial if it is possible to reduce the cantilever’s length; otherwise, the use of 30° should be considered. Comparing with PEEK, the YTZP and CoCr concentrated stress in the framework structure, reducing the stress in the prosthetic screw.

Three-Dimensional Finite Element Investigation into Effects of Implant Thread Design and Loading Rate on Stress Distribution in Dental Implants and Anisotropic Bone

Variations in the implant thread shape and occlusal load behavior may result in significant changes in the biological and mechanical properties of dental implants and surrounding bone tissue. Most previous studies consider a single implant thread design, an isotropic bone structure, and a static occlusal load. However, the effects of different thread designs, bone material properties, and loading conditions are important concerns in clinical practice. Accordingly, the present study performs Finite Element Analysis (FEA) simulations to investigate the static, quasi-static and dynamic response of the implant and implanted bone material under various thread designs and occlusal loading directions (buccal-lingual, mesiodistal and apical). The simulations focus specifically on the von Mises stress, displacement, shear stress, compressive stress, and tensile stress within the implant and the surrounding bone. The results show that the thread design and occlusal loading rate have a significant effect on the stress distribution and deformation of the implant and bone structure during clinical applications. Overall, the results provide a useful insight into the design of enhanced dental implants for an improved load transfer efficiency and success rate.

Novel Design and Finite Element Analysis of Diamond-like Porous Implants with Low Stiffness

The purpose of this study was to design porous implants with low stiffness and evaluate their biomechanical behavior. Thus, two types of porous implants were designed (Type I: a combined structure of diamond-like porous scaffold and traditional tapered thread. Type II: a cylindrical porous scaffold filled by arrayed basic diamond-like pore units). Three implant-supported prosthesis models were constructed from Type I, Type II and commercial implants (control group) and were evaluated by finite element analysis (FEA). The stress distribution pattern of the porous implants were assessed and compared with the control group. In addition, the stiffness of the cylindrical specimens simplified from three types of implants was calculated. The Type I implant exhibited better stress distribution than the Type II implant. The maximum stress between the cortical bone–Type I implant interface was 12.9 and 19.0% lower than the other two groups. The peak stress at the cancellous bone–Type I implant interface was also reduced by 16.8 and 38.7%. Compared with the solid cylinder, the stiffness of diamond-like pore cylinders simplified from the two porous implants geometry was reduced by 61.5 to 76.1%. This construction method of porous implant can effectively lower its stiffness and optimize the stress distribution at the implant–bone interface.

Mechanical Response of PEKK and PEEK As Frameworks for Implant-Supported Full-Arch Fixed Dental Prosthesis: 3D Finite Element Analysis

Objective  Polymeric framework represent an innovative approach for implant-supported dental prostheses. However, the mechanical response of ultra-high performance polymers as frameworks for full-arch prostheses under the “all-on-four concept” remains unclear. The present study applied finite element analysis to examine the behavior of polyetherketoneketone (PEKK) and polyetheretherketone (PEEK) prosthetic frameworks.

Materials and Methods  A three-dimensional maxillary model received four axially positioned morse-taper implants, over which a polymeric bar was simulated. The full-arch prosthesis was created from a previously reported database model, and the imported geometries were divided into a mesh composed of nodes and tetrahedral elements in the analysis software. The materials were assumed as isotropic, elastic, and homogeneous, and all contacts were considered bonded. A normal load (500 N magnitude) was applied at the occlusal surface of the first left molar after the model was fixed at the base of the cortical bone. The microstrain and von-Mises stress were selected as criteria for analysis.

Results  Similarities in the mechanical response were observed in both framework for the peri-implant tissue, as well as for stress generated in the implants (263–264 MPa) and abutments (274–273 MPa). The prosthetic screw and prosthetic base concentrated more stress with PEEK (211 and 58 MPa, respectively) than with PEKK (192 and 49 MPa), while the prosthetic framework showed the opposite behavior (59 MPa for PEEK and 67 MPa for PEKK).

Conclusion  The main differences related to the mechanical behavior of PEKK and PEEK frameworks for full-arch prostheses under the “all-on-four concept” were reflected in the prosthetic screw and the acrylic base. The superior shock absorbance of PEKK resulted in a lower stress concentration on the prosthetic screw and prosthetic base. This would clinically represent a lower fracture risk on the acrylic base and screw loosening. Conversely, lower stress concentration was observed on PEEK frameworks.

The role of cortical zone level and prosthetic platform angle in dental implant mechanical response: A 3D finite element analysis

OBJECTIVE

The aim of this study was to evaluate the influence of three different dental implant neck geometries, under a combined compressive/shear load using finite element analysis (FEA). The implant neck was positioned in D2 quality bone at the crestal level or 2 mm below.

METHODS

One dental implant (4.2 × 9 mm) was digitized by reverse engineering techniques using micro CT and imported into Computer Aided Design (CAD) software. Non-uniform rational B-spline surfaces were reconstructed, generating a 3D volumetric model similar to the digitized implant. Three different models were generated with different implant neck configurations, namely 0°, 10° and 20°. D2 quality bone, composed of cortical and trabecular structure, was modeled using data from CT scans. The implants were included in the bone model using a Boolean operation. Two different fixture insertion depths were simulated for each implant: 2 mm below the crestal bone and exactly at the level of the crestal bone. The obtained models were imported to FEA software in STEP format. Von Mises equivalent strains were analyzed for the peri-implant D2 bone type, considering the magnitude and volume of the affected surrounding cortical and trabecular bone. The highest strain values in both cortical and trabecular tissue at the peri-implant bone interface were extracted and compared.

RESULTS

All implant models were able to distribute the load at the bone-implant contact (BIC) with a similar strain pattern between the models. At the cervical region, however, differences were observed: the models with 10° and 20° implant neck configurations (Model B and C), showed a lower strain magnitude when compared to the straight neck (Model A). These values were significantly lower when the implants were situated at crestal bone levels. In the apical area, no differences in strain values were observed.

SIGNIFICANCE

The implant neck configuration influenced the strain distribution and magnitude in the cortical bone and cancellous bone tissues. To reduce the strain values and improve the load dissipation in the bone tissue, implants with 10° and 20 neck configuration should be preferred instead of straight implant platforms.

Evaluation of Stresses on Implant, Bone, and Restorative Materials Caused by Different Opposing Arch Materials in Hybrid Prosthetic Restorations Using the All-on-4 Technique

The long-term success of dental implants is greatly influenced by the use of appropriate materials while applying the “All-on-4” concept in the edentulous jaw. This study aims to evaluate the stress distribution in the “All-on-4” prosthesis across different material combinations using three-dimensional finite element analysis (FEA) and to evaluate which opposing arch material has destructive effects on which prosthetic material while offering certain recommendations to clinicians accordingly. Acrylic and ceramic-based hybrid prosthesis have been modelled on a rehabilitated maxilla using the “All-on-4” protocol. Using different materials and different supports in the opposing arch (natural tooth, and implant/ceramic, and acrylic), a multi-vectorial load has been applied. To measure stresses in bone, maximum and minimum principal stress values were calculated, while Von Mises stress values were obtained for prosthetic materials. Within a single group, the use of an acrylic implant-supported prosthesis as an antagonist to a full arch implant-supported prosthesis yielded lower maximum (Pmax) and minimum (Pmin) principal stresses in cortical bone. Between different groups, maxillary prosthesis with polyetheretherketone as framework material showed the lowest stress values among other maxillary prostheses. The use of rigid materials with higher moduli of elasticity may transfer higher stresses to the peri implant bone. Thus, the use of more flexible materials such as acrylic and polyetheretherketone could result in lower stresses, especially upon atrophic bones.

Effect of Direct and Indirect Materials on Stress Distribution in Class II MOD Restorations: A 3D-Finite Element Analysis Study

The aim of this study is to investigate the stress distributions of different restoration options for class II mesio-occluso-distal (MOD) cavities. A class II MOD cavity with proximal box gingival floor 1 mm below cementoenamel junction was designed in a mandibular first molar tooth model. 3D finite-element analysis (FEA) and 3D-CAD modelling were used to examine the occlusal stresses distributed to the remaining buccal enamel (RBE), remaining lingual enamel (RLE), adhesive surfaces, and restorative materials by direct and indirect materials resulting from a 600 N of static occlusal load stimulating foodstuff. von Mises (VM) and maximum principal (Pmax) stresses were evaluated for two CAD/CAM materials and three direct materials. CAD/CAM materials exerted less stress than the direct restorative materials. Significant von Mises and Pmax stress value differences were seen among all restoration models on RBE. Reducing RLE and including it into the cavity would be a more effective option for this model in this scenario. As VM and Pmax stresses of PIHC CAD/CAM material for RBE and dentin were significantly lower than other tested materials, it may be the choice of material for indirect MOD restorations.

Computer Aided Design Modelling and Finite Element Analysis of Premolar Proximal Cavities Restored with Resin Composites

This study evaluated the stress distribution in five different class II cavities of premolar models restored with conventional or bulk-fill flowable composite by means of finite element analysis (FEA) under shrinkage and occlusal loading. An upper validated premolar model was imported in the software, and five class II cavities with different occlusal extensions and dimensions were prepared: horizontal cavity on the mesial surface (horizontal slot), mesio-occlusal cavity, mesial cavity (vertical slot), tunnel type cavity and direct access cavity. The models were restored with conventional or bulk-fill flowable resin composite. The tested materials were considered as homogeneous, linear, and isotropic. The Maximum Principal Stress criteria was chosen to evaluate the tensile stress results. The lowest shrinkage stress value was observed in the direct access cavity restored with bulk-fill flowable resin composite (36.12 MPa). The same cavity, restored with conventional composite showed a score of 36.14 MPa. The horizontal slot cavity with bulk-fill flowable showed a score of 46.71 MPa. The mesio-occlusal cavity with bulk-fill flowable had a score of 53.10 MPa, while with conventional composite this was 55.35 MPa. Higher shrinkage stress was found in the vertical slot cavity with conventional resin 56.14 MPa, followed by the same cavity with bulk-fill flowable 56.08 MPa. Results indicated that the use of bulk-fill flowable composite resin more significantly decreased the polymerization shrinkage stress magnitude. The larger the cavity and the volume of material necessary to restore the tooth, the greater the residual stress on enamel and dentin tissue.

3D Finite Element Analysis of Rotary Instruments in Root Canal Dentine with Different Elastic Moduli

The aim of the present investigation was to calculate the stress distribution generated in the root dentine canal during mechanical rotation of five different NiTi endodontic instruments by means of a finite element analysis (FEA). Two conventional alloy NiTi instruments F360 25/04 and F6 Skytaper 25/06, in comparison to three heat treated alloys NiTI Hyflex CM 25/04, Protaper Next 25/06 and One Curve 25/06 were considered and analyzed. The instruments’ flexibility (reaction force) and geometrical features (cross section, conicity) were previously investigated. For each instrument, dentine root canals with two different elastic moduli(18 and 42 GPa) were simulated with defined apical ratios. Ten different CAD instrument models were created and their mechanical behaviors were analyzed by a 3D-FEA. Static structural analyses were performed with a non-failure condition, since a linear elastic behavior was assumed for all components. All the instruments generated a stress area concentration in correspondence to the root canal curvature at approx. 7 mm from the apex. The maximum values were found when instruments were analyzed in the highest elastic modulus dentine canal. Strain and von Mises stress patterns showed a higher concentration in the first part of curved radius of all the instruments. Conventional Ni-Ti endodontic instruments demonstrated higher stress magnitudes, regardless of the conicity of 4% and 6%, and they showed the highest von Mises stress values in sound, as well as in mineralized dentine canals. Heat-treated endodontic instruments with higher flexibility values showed a reduced stress concentration map. Hyflex CM 25/04 displayed the lowest von Mises stress values of, respectively, 35.73 and 44.30 GPa for sound and mineralized dentine. The mechanical behavior of all rotary endodontic instruments was influenced by the different elastic moduli and by the dentine canal rigidity.

Lithium Disilicate Ceramic Endocrown Biomechanical Response According to Different Pulp Chamber Extension Angles and Filling Materials

The purpose of this study is to evaluate the effect of pulp chamber extension angles and filling material mechanical properties on the biomechanical response of a ceramic endocrown. A 3D model of maxillary molar that underwent endodontically treatment was exported to computer aided design software to conduct finite element analysis (FEA). The endocrown model was modified considering different pulp chamber extension angles (right angle; 6°, 12° and 18° of axial divergence). The solids were imported into the computer aided engineering software in Standard for the Exchange of Product Data (STEP) format. Nine different filling materials were simulated to seal the orifice of the root canal system under each endocrown restoration (resin composite, bulk-fill resin composite, alkasite, flowable resin composite, glass ionomer cement, autocured resin-reinforced glass ionomer cement, resin cement, bulk-fill flowable resin composite, zinc oxide cement), totaling 36 models. An axial load (300 N) was applied at the occlusal surface. Results were determined by colorimetric graphs of von-Misses stress (VMS) and Maximum Principal Stress (MPS) on tooth, cement layer, and endocrown restorations. VMS distribution showed a similar pattern between the models, with more stress at the load region for the right-angled endocrowns. The MPS showed that the endocrown intaglio surface and cement layer showed different mechanical responses with different filing materials and pulp chamber angles. The stress peaks plotted in the dispersion plot showed that the filling material stiffness is proportional to the stress magnitude in the endocrown, cement layer and tooth adhesive surface. In addition, the higher the pulp chamber preparation angle, the higher the stress peak in the restoration and tooth, and the lower the stress in the cement layer. Therefore, 6° and 12° pulp chamber angles showed more promising balance between the stresses of the adhesive interface structures. Under the conditions of this study, rigid filling materials were avoided to seal the orifice of root canal system when an endocrown restoration was planned as rehabilitation. In addition, the pulp chamber axial walls were prepared between 6° and 12° of divergence to balance the stress magnitude in the adhesive interface for this treatment modality.

Dental Materials Coatings: Effect on the Clinical Behavior

n/a

Stress distribution on different bar materials in implant-retained palatal obturator

Implant-retained custom-milled framework enhances the stability of palatal obturator prostheses. Therefore, to evaluate the mechanical response of implant-retained obturator prostheses with bar-clip attachment and milled bars, in three different materials under two load incidences were simulated. A maxilla model which Type IIb maxillary defect received five external hexagon implants (4.1 x 10 mm). An implant-supported palatal obturator prosthesis was simulated in three different materials: polyetheretherketone (PEEK), titanium (Ti:90%, Al:6%, V:4%) and Co-Cr (Co:60.6%, Cr:31.5%, Mo:6%) alloys. The model was imported into the analysis software and divided into a mesh composed of nodes and tetrahedral elements. Each material was assumed isotropic, elastic and homogeneous and all contacts were considered ideal. The bone was fixed and the load was applied in two different regions for each material: at the palatal face (cingulum area) of the central incisors (100 N magnitude at 45°); and at the occlusal surface of the first left molar (150 N magnitude normal to the surface). The microstrain and von-Mises stress were selected as criteria for analysis. The posterior load showed a higher strain concentration in the posterior peri-implant tissue, near the load application side for cortical and cancellous bone, regardless the simulated material. The anterior load showed a lower strain concentration with reduced magnitude and more implants involving in the load dissipation. The stress peak was calculated during posterior loading, which 77.7 MPa in the prosthetic screws and 2,686 με microstrain in the cortical bone. For bone tissue and bar, the material stiffness was inversely proportional to the calculated microstrain and stress. However, for the prosthetic screws and implants the PEEK showed higher stress concentration than the other materials. PEEK showed a promising behavior for the bone tissue and for the integrity of the bar and bar-clip attachments. However, the stress concentration in the prosthetic screws may represent an increase in failure risk. The use of Co-Cr alloy can reduce the stress in the prosthetic screw; however, it increases the bone strain; while the Titanium showed an intermediate behavior.