3-D Printable Polymer Pelletizer Chopper for Fused Granular Fabrication-Based Additive Manufacturing

The Quest for the Holy Grail Of 3D Printing: A Critical Review of Recycling in Polymer Powder Bed Fusion Additive Manufacturing

The benefits of additive manufacturing (AM) are widely recognised, boosting the AM method's use in industry, while it is predicted AM will dominate the global manufacturing industry. Alas, 3D printing's growth is hindered by its sustainability. AM methods generate vast amounts of residuals considered as waste, which are disposed of. Additionally, the energy consumed, the materials used, and numerous other factors render AM unsustainable. This paper aims to bring forward all documented solutions in the literature. The spotlight is on potential solutions for the Powder Bed Fusion (PBF) AM, focusing on Selective Laser Sintering (SLS), as these are candidates for mass manufacturing by industry. Solutions are evaluated critically, to identify research gaps regarding the recyclability of residual material. Only then can AM dominate the manufacturing industry, which is extremely important since this is a milestone for our transition into sustainable manufacturing. This transition itself is a complex bottleneck on our quest for becoming a sustainable civilisation. Unlike previous reviews that primarily concentrate on specific AM recycling materials, this paper explores the state of the art in AM recycling processes, incorporating the latest market data and projections. By offering a holistic and forward-looking perspective on the evolution and potential of AM, this review serves as a valuable resource for researchers and industry professionals alike.

Instrumented open-source filament extruder for research and education

Extruders are necessary equipment for 3D filament manufacturing, which is considered a clean technology because it has less scrap and can reuse materials, increasing its life cycle. Open source extruders are less expensive than industrial extruders. However, they have little instrumentation, which limits processing analysis and thus the development of new materials, screw design and process control. Therefore, this project aims to develop a low-cost extruder with a high degree of instrumentation for in-situ process analysis. To achieve this, equipment was developed with an integrated circuit board, both with modularity, machine and peripheral control, process stability, and data acquisition. To validate the equipment, processing was done at constant temperature and with flow variation. The data obtained were the temperatures at different points in the barrel, the rotation speed of the extruder motor, the current consumed by the motor and the resistances, and the speed of the extruder motor. Thermal images of the components were obtained during processing, validating the type of material used in the parts manufactured by additive manufacturing. The ABS filament produced was analyzed by flow and surface analysis using a confocal microscope. Higher flow rates had a better surface quality of the filament.

Manufacturing Zero-Waste COVID-19 Personal Protection Equipment: a Case Study of Utilizing 3D Printing While Employing Waste Material Recycling

COVID-19 pandemic outbreak dictated the extensive use of personal protective equipment (PPE) by the majority of the population and mostly by frontline professionals. This need triggered a sudden demand that led to a global shortage of available PPEs threatening to have an immense contribution to the virus contamination spread. In these conditions, the need for a local, flexible, and rapid manufacturing method that would be able to cope with the increased demand for PPE fabrication arose. 3D printing proved to be such a manufacturing technique since its working principles make it an ideal technology for local, decentralized production of PPEs meeting the local demands. While considered to be more environmentally friendly than conventional fabrication techniques and aligning well with the principles of sustainability and circular economy, 3D printing can produce waste as the result of potential failed prints and material used for the fabrication of support structures. This paper describes the case of utilizing pre-existing FDM 3D printing equipment in an academic facility for the production of PPEs (face shields) and their distribution according to local demands. The plastic wastes produced were forwarded to a recycling process that led to their conversion to 3D filament that would be returned to the academic facility as raw material for future 3D printing operations. The followed procedure minimized 3D printing waste and led to a zero-waste fabrication case that was initiated in a pandemic for a greater-good cause (production of COVID-19 fighting PPEs) while assimilating the values of sustainability and circular economy.

Waste Valorization through Additive Manufacturing in an Industrial Symbiosis Setting

Given the current environmental concerns related to manufacturing, the introduction to the industrial symbiosis concept brought purpose to waste, instead of disposing it in landfills or eliminating it through incineration. The waste generated by industrial processes, or end-of-life products, is redirected to be used as a “new” input in another process by one or more organizations, which is a mutual benefit or a “symbiosis”. Despite its relevancy, the industrial symbiosis concept is marginally explored in the context of additive manufacturing; this emerging technology has disruptive potential regarding the use of different materials as secondary raw materials. This paper presents a systematic literature review regarding industrial symbiosis and additive manufacturing. The main objective is to identify how wastes can be used as input materials to additive manufacturing processes and what exchanges of resources occur in an industrial symbiosis setting. A final sample of 32 documents was reached and analyzed. Five examples of using waste streams in additive manufacturing processes to produce goods were highlighted and explored.

Distributed Manufacturing of Open Source Medical Hardware for Pandemics

Distributed digital manufacturing offers a solution to medical supply and technology shortages during pandemics. To prepare for the next pandemic, this study reviews the state-of-the-art of open hardware designs needed in a COVID-19-like pandemic. It evaluates the readiness of the top twenty technologies requested by the Government of India. The results show that the majority of the actual medical products have some open source development, however, only 15% of the supporting technologies required to produce them are freely available. The results show there is still considerable research needed to provide open source paths for the development of all the medical hardware needed during pandemics. Five core areas of future research are discussed, which include (i) technical development of a wide-range of open source solutions for all medical supplies and devices, (ii) policies that protect the productivity of laboratories, makerspaces, and fabrication facilities during a pandemic, as well as (iii) streamlining the regulatory process, (iv) developing Good-Samaritan laws to protect makers and designers of open medical hardware, as well as to compel those with knowledge that will save lives to share it, and (v) requiring all citizen-funded research to be released with free and open source licenses.