Influence of the Computer-Aided Static Navigation Technique on the Accuracy of the Orthodontic Micro-Screws Placement: An In Vitro Study

Midpalatal miniscrew insertion: The accuracy of digital planning and surgical placement

INTRODUCTION

The objective of this study was to investigate the accuracy of palatal miniscrew insertion, evaluating the effect of guide fabrication and surgical placement.

METHODS

Guided insertion of bilateral paramedian palatal miniscrews was undertaken using Appliance Designer software (3Shape, Copenhagen, Denmark). A resin surgical guide (P Pro Surgical Guide; Straumann AG, Basel, Switzerland) was used. Superimposition of the miniscrew position relative to the digital design was undertaken using bespoke software (Inspect 3D module, OnyxCeph; Image Instruments GmbH, Chemnitz, Germany) to assess surgical inaccuracy. Miniscrew position relative to the surgical guide was also assessed to isolate the effect of planning inaccuracies. Both horizontal and vertical discrepancies were evaluated at both implant locations.

RESULTS

Twenty-seven patients having bilateral palatal insertions were examined. Mean discrepancies were <0.5 mm, both in the horizontal and vertical planes. The mean overall horizontal and vertical discrepancy between the digital design and final miniscrew position on the left side was 0.32 ± 0.15 mm and 0.34 ± 0.17 mm, respectively. The maximum horizontal discrepancy observed was 0.72 mm. No significant differences were observed in relation to the accuracy of mini-implant positioning on the basis of sidedness, either for horizontal (P = 0.29) or vertical (P = 0.86) discrepancy.

CONCLUSIONS

High levels of accuracy associated with guided insertion of paramedian palatal implants were recorded with mean discrepancies of less than 0.5 mm both in the horizontal and vertical planes. No difference in accuracy was noted between the left and right sides. Very minor levels of inaccuracy associated both with surgical techniques and surgical guide fabrication were recorded.

Vertical changes in the hard tissues after space closure by miniscrew sliding mechanics: a three-dimensional modality analysis

OBJECTIVES

This study aimed to investigate vertical changes in the maxillary central incisor and the maxillary first molar, along with alterations in the mandibular plane angle during space closure using miniscrew sliding mechanics.

METHODS

Twenty adult patients treated at Peking University Hospital of Stomatology between 2008 and 2013 were included. Digital dental models and craniofacial cone-beam computed tomography (CBCT) scans were obtained at the start of treatment (T0) and immediately after space closure (T1). Stable miniscrews were used for superimposing maxillary digital dental models (T0 and T1), and vertical changes in the maxillary first molar and the maxillary central incisor were measured. Three-dimensional changes in the mandibular plane were assessed through CBCT superimposition.

RESULTS

The maxillary central incisor exhibited an average extrusion of 2.56 ± 0.18 mm, while the maxillary first molar showed an average intrusion of 1.25 ± 1.11 mm with a distal movement of 0.97 ± 0.99 mm. Additionally, the mandibular plane angle decreased by an average of 0.83 ± 1.65°. All three indices exhibited statistically significant differences.

CONCLUSION

During space closure using the miniscrew sliding technique, significant changes occurred in both the sagittal and vertical dimensions of the upper dentition. This included extrusion of the maxillary central incisors, intrusion of the maxillary first molars, and a slight counterclockwise rotation of the mandibular plane.

Comparative analysis of two navigation techniques based on augmented reality technology for the orthodontic mini-implants placement

To analyze and compare the accuracy and root contact prevalence, comparing a conventional freehand technique and two navigation techniques based on augmented reality technology for the orthodontic self-drilling mini-implants placement. Methods Two hundred and seven orthodontic self-drilling mini-implants were placed using either a conventional freehand technique (FHT) and two navigation techniques based on augmented reality technology (AR TOOTH and AR SCREWS). Accuracy across different dental sectors was also analyzed. CBCT and intraoral scans were taken both prior to and following orthodontic self-drilling mini-implants placement. The deviation angle and horizontal were then analyzed; these measurements were taken at the coronal entry point and apical endpoint between the planned and performed orthodontic self-drilling mini-implants. In addition, any complications resulting from mini-implant placement, such as spot perforations, were also analyzed across all dental sectors.Results The statistical analysis showed significant differences between study groups with regard to the coronal entry-point (p < 0.001), apical end-point(p < 0.001) and angular deviations (p < 0.001). Furthermore, statistically significant differences were shown between the orthodontic self-drilling mini-implants placement site at the coronal entry-point (p < 0.0001) and apical end-point (p < 0.001). Additionally, eight root perforations were observed in the FHT group, while there were no root perforations in the two navigation techniques based on augmented reality technology.Conclusions The navigation techniques based on augmented reality technology has an effect on the accuracy of orthodontic self-drilling mini-implants placement and results in fewer intraoperative complications, comparing to the conventional free-hand technique. The AR TOOTH augmented reality technique showed more accurate results between planned and placed orthodontic self-drilling mini-implants, comparing to the AR SCREWS and conventional free-hand techniques. The navigation techniques based on augmented reality technology showed fewer intraoperative complications, comparing to the conventional free-hand technique.