Effect of Applied Stress on the Mechanical Properties of a Zr-Cu-Ag-Al Bulk Metallic Glass with Two Different Structure States

Nanoindentation Investigation on the Size-Dependent Creep Behavior in a Zr-Cu-Ag-Al Bulk Metallic Glass

Nanoindentation technology has been widely adopted to study creep behavior in small regions. However, nanoindentation creep behavior of metallic glass is still not well understood. In the present work, we investigated nanoindentation size effects on creep deformation in a Zr-based bulk metallic glass at room temperature. The total creep strain and strain rate of steady-state creep were gradually decreased with increasing holding depth under a Berkovich indenter, indicating a length-scale-dependent creep resistance. For a spherical indenter, creep deformations were insignificant in elastic regions and then greatly enhanced by increasing holding strain in plastic regions. Strain rate sensitivities (SRS) decreased with increasing holding depth and holding strain at first, and then stabilized as holding depth was beyond about 500 nm for both indenters. SRS values were 0.4–0.5 in elastic regions, in which atomic diffusion and free volume migration could be the creep mechanism. On the other hand, evolution of the shear transformation zone was suggested as a creep mechanism in plastic regions, and the corresponding SRS values were in the range of 0.05 to 0.3.

Room-Temperature Creep Behavior and Activation Volume of Dislocation Nucleation in a LiTaO3 Single Crystal by Nanoindentation

The crystal orientation effect on mechanical heterogeneity of LiTaO₃ single crystals is well known, whilst the time-dependent plastic behavior, i.e., creep is still short of understanding. Relying on nanoindentation technology, we systematically studied room-temperature creep flows at various holding depths (100 nm to 1100 nm) in three typical orientations namely the X-112°, Y-36° and Y-42° planes. Creep resistance was much stronger in the X-112° plane than the others. In the meanwhile, creep features were similar in the Y-36° and Y-42° planes. The orientation effect on creep deformation was consistent with that on hardness. The nanoindentation length scale played an important role in creep deformation that creep strains were gradually decreased with the holding depth in all the planes. Based on strain rate sensitivity and yield stress, the activation volumes of dislocation nucleation were computed at various nanoindentation depths. The activation volumes ranged from 5 ų to 23 ų for the Y-36° and Y-42° planes, indicating that a point-like defect could be the source of plastic initiation. In the X-112° plane, the activation volume was between 6 ų and 83 ų. Cooperative migration of several atoms could also be the mechanism of dislocation activation at deep nanoindentation.

Nanoindentation of γ-TiAl with Different Crystal Surfaces by Molecular Dynamics Simulations

The periodicity and density of atomic arrangement vary with the crystal orientation, which results in different deformation mechanisms and mechanical properties of γ-TiAl. In this paper, the anisotropic characteristics for γ-TiAl with (100), (1¯10) and (111) surfaces during nanoindentation at 300 K have been investigated by molecular dynamics simulations. It is found that there is no obvious pop-in event in all load-depth curves when the initial plastic deformation of γ-TiAl samples occurs, because the dislocation nucleates before the first load-drop; while a peak appears in both the unloading curves of the (1¯10) and (111) samples due to the release of energy. Stacking faults, twin boundaries and vacancies are formed in all samples; however, interstitials are formed in the (100) sample, a stacking fault tetrahedron is formed in the (111) sample; and two prismatic dislocation loops with different activities are formed in the (1¯10) and (111) samples, respectively. It is also concluded that the values of the critical load, strain energy, hardness and elastic modulus for the (111) sample are the maximum, and for the (100) sample are the minimum. Furthermore, the orientation dependence of the elastic modulus is greater than the hardness and critical load.

Testing Effects on Shear Transformation Zone Size of Metallic Glassy Films Under Nanoindentation

Room-temperature creep tests are performed at the plastic regions of two different metallic glassy films under Berkovich nanoindetation. Relying on the strain rate sensitivity of the steady-state creep curve, shear transformation zone (STZ) size is estimated based on the cooperative shear model (CSM). By applying various indentation depths, loading rates, and holding times, the testing effects on the STZ size of metallic glasses are systematically studied. Experimental results indicate that STZ size is greatly increased with increased indentation depth and shortened holding time. Meanwhile, STZ size is weakly dependent on the loading history. Both the intrinsic and extrinsic reasons are discussed, to reveal the testing effects on the nanoindentation creep flow and STZ size.

Controlling the Mechanical Properties of Bulk Metallic Glasses by Superficial Dealloyed Layer

Cu₅₀Zr₄₅Al₅ bulk metallic glass (BMG) presents high fracture strength. For improving its plasticity and controlling its mechanical properties, superficial dealloying of the BMG was performed. A composite structure containing an inner rod-shaped Cu-Zr-Al amorphous core with high strength and an outer dealloyed nanoporous layer with high energy absorption capacity was obtained. The microstructures and mechanical properties of the composites were studied in detail. It was found, for the first time, that the mechanical properties of Cu₅₀Zr₄₅Al₅ BMG can be controlled by adjusting the width of the buffer deformation zone in the dealloyed layer, which can be easily manipulated with different dealloying times. As a result, the compressive strength, compressive strain, and energy absorption capacity of the BMGs can be effectively modulated from 0.9 to 1.5 GPa, from 2.9% to 4.7%, and from 29.1 to 40.2 MJ/m³, respectively. The paper may open a door for developing important engineering materials with regulable and comprehensive performances.