1
|
Matta A, Yadavalli VR, Manas L, Kadleckova M, Pavlinek V, Sedlacek T. Surface Treatments' Influence on the Interfacial Bonding between Glass Fibre Reinforced Elium ® Composite and Polybutylene Terephthalate. MATERIALS (BASEL, SWITZERLAND) 2024; 17:3276. [PMID: 38998358 PMCID: PMC11243668 DOI: 10.3390/ma17133276] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Subscribe] [Scholar Register] [Received: 05/21/2024] [Revised: 06/28/2024] [Accepted: 07/01/2024] [Indexed: 07/14/2024]
Abstract
This study examines the process of using injection moulding to join two different materials to manufacture bi-component moulded products with improved performance characteristics. The two-component process, which combines the advantages of two different technologies-the high efficiency of the injection moulding process and the excellent mechanical properties of long glass fibre composites produced by resin transfer moulding (RTM) technology-offers a particular advantage and improved applicability of the prepared lightweight products in both the automotive and aerospace sectors. The composite studied here consists of Elium® thermoplastic resin (30%) reinforced with unwoven glass fibre fabric (70%) using the RTM process. The Elium® composite sample is consequently used as an insert overmoulded with polybutylene terephthalate (PBT) homopolymer reinforced with 20% w/w of short glass fibre through injection moulding. The influence of different mould temperatures and surface treatments on the adhesion between the materials used is investigated by evaluating the mechanical performance using tensile shear strength tests. It was found that while an increase in mould temperature from 40 °C to 120 °C resulted in a doubling of the initial average bond strength between untreated Elium® RTM inserts and overmoulded PBT parts (0.9 MPa), sandblasting the inserts ensured a further tripling of the bond strength of the composites to a value of 5.4 MPa.
Collapse
Affiliation(s)
- Ashish Matta
- Department of Polymer Engineering, Faculty of Technology, Tomas Bata University in Zlin, Vavreckova 5669, 760 01 Zlin, Czech Republic;
| | - Venkat Reddy Yadavalli
- Department of Applied Logistics and Polymer Sciences, Hochschule Kaiserslautern, University of Applied Sciences, 67659 Pirmasens, Germany;
| | - Lukas Manas
- Centre of Polymer Systems, Tomas Bata University in Zlin, Trida Tomase Bati 5678, 760 01 Zlin, Czech Republic; (M.K.); (T.S.)
- Department of Production Engineering, Faculty of Technology, Tomas Bata University in Zlin, Vavreckova 5669, 760 01 Zlin, Czech Republic
| | - Marketa Kadleckova
- Centre of Polymer Systems, Tomas Bata University in Zlin, Trida Tomase Bati 5678, 760 01 Zlin, Czech Republic; (M.K.); (T.S.)
- Department of Physics and Materials Engineering, Faculty of Technology, Tomas Bata University in Zlin, Vavreckova 5669, 760 01 Zlin, Czech Republic
| | | | - Tomas Sedlacek
- Centre of Polymer Systems, Tomas Bata University in Zlin, Trida Tomase Bati 5678, 760 01 Zlin, Czech Republic; (M.K.); (T.S.)
| |
Collapse
|
2
|
Bhudolia SK, Gohel G, Vasudevan D, Leong KF, Gerard P. On the Mode I and Mode II Delamination Characteristics and Surface Morphological Aspects of Composites with Carbon-Thermoplastic Hybrid Fabrics and Innovative Liquid Thermoplastic Resin. Polymers (Basel) 2022; 14:polym14194155. [PMID: 36236103 PMCID: PMC9573496 DOI: 10.3390/polym14194155] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 08/23/2022] [Revised: 09/15/2022] [Accepted: 09/25/2022] [Indexed: 11/04/2022] Open
Abstract
In the current research, the delamination behavior under Mode I and Mode II loading for the hybrid carbon-thermoplastic fabrics in conjunction with novel liquid thermoplastic acrylic Elium® resin processable at ambient conditions was studied. The experimentation by incorporating doublers methodology, studying the performance under Mode I and Mode II loading, and understanding failure mechanisms using surface morphological fractography is deliberated. Hybrid Carbon-Ultra-high molecular weight polyethylene (UHMWPP)/Elium® composite has shown a 22.81% higher GIC and a 22.2% higher GIIC than Carbon-UHMWPP/Epoxy composite. On the contrary, the Carbon_Ultra-high molecular weight polypropylene (UHMWPE)/Elium® has shown an 11.11% higher Mode I critical energy release rate (GIC) and a 7.58% higher Mode II critical energy release rate (GIIC) than Carbon_UHMWPE/Epoxy composite. Hybrid fiber reinforced thermoplastic composites have shown severe plastic deformation of the matrix, rough fracture surface, and micro-cracks on the de-bonding surface, extensive fiber bridging, and crack branching which contributed to the improvement in the delamination behavior. Hybrid fiber architecture is also found to be detrimental by inducing crack arresting mechanisms including the tortuous crack path and the resin-rich pockets path due to the mismatch of the size of the fiber yarns.
Collapse
Affiliation(s)
- Somen K. Bhudolia
- School of Mechanical and Aerospace Engineering, Nanyang Technological University, 50, Nanyang Avenue, Singapore 639798, Singapore
- Correspondence:
| | - Goram Gohel
- School of Mechanical and Aerospace Engineering, Nanyang Technological University, 50, Nanyang Avenue, Singapore 639798, Singapore
| | - Durga Vasudevan
- School of Mechanical and Aerospace Engineering, Technical University of Munich Asia, 25 International Business Park Rd, Singapore 609916, Singapore
| | - Kah Fai Leong
- School of Mechanical and Aerospace Engineering, Nanyang Technological University, 50, Nanyang Avenue, Singapore 639798, Singapore
| | - Pierre Gerard
- Groupement de Recherche de Lacq, Arkema, Route Départementale 817, BP 34, 64170 Lacq, France
| |
Collapse
|
3
|
Gohel G, Soh CZ, Leong KF, Gerard P, Bhudolia SK. Effect of PMMA Coupling Layer in Enhancing the Ultrasonic Weld Strength of Novel Room Temperature Curable Acrylic Thermoplastic to Epoxy Based Composites. Polymers (Basel) 2022; 14:polym14091862. [PMID: 35567030 PMCID: PMC9105686 DOI: 10.3390/polym14091862] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.5] [Reference Citation Analysis] [Abstract] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 04/04/2022] [Revised: 04/28/2022] [Accepted: 04/28/2022] [Indexed: 02/04/2023] Open
Abstract
The joining of composites can be performed in an extremely short time with more energy-efficient ultrasonic welding techniques. The current research investigated the performance optimization of ultrasonic welding of carbon/Elium® composite to carbon/epoxy composite using a polymethyl methacrylate (PMMA) coupling interlayer. The weld strength was quantified by static lap shear strength (LSS) testing. A new methodology was used by creating a PMMA coupling layer on the epoxy composite adherend to achieve an improved interphase and thus enhance the weld properties. The LSS of Elium (EL)-Epoxy (EP) _0.25_0.25 was found to be 190% higher compared to that of EL-EP, confirming the effectiveness of the strategy used for creating an interlayer thermoplastic coupling layer. The time required for welding was optimized to be 2s as compared to 10 min required for adhesive bonding. Scanning electron microscopic images of epoxy and PMMA/Elium matrix interphase were observed to have a rough surface and remained largely unaffected by welding. There was an interphase change further away from the interphase to a rougher texture. There was little to no effect on the penultimate layer on the weld strength, as no interphase change could be observed after welding. Fractography investigation revealed shear cusps, matrix plastic deformation, fiber imprints, fiber pull-out, and good adhesion between matrix and fiber, features seen for configuration with maximum LSS. The current research findings present a way to join Elium® with epoxy composites that could be used in applications that require a selective strengthening, such as in sporting goods and consumer products. Furthermore, a detailed investigation is ongoing to use different filler particles and coupling layers to reach the maximum welding performance.
Collapse
Affiliation(s)
- Goram Gohel
- School of Mechanical and Aerospace Engineering, Nanyang Technological University, 50 Nanyang Avenue, Singapore 639798, Singapore; (C.Z.S.); (K.F.L.)
- Correspondence: (G.G.); (S.K.B.)
| | - Chun Zhi Soh
- School of Mechanical and Aerospace Engineering, Nanyang Technological University, 50 Nanyang Avenue, Singapore 639798, Singapore; (C.Z.S.); (K.F.L.)
| | - Kah Fai Leong
- School of Mechanical and Aerospace Engineering, Nanyang Technological University, 50 Nanyang Avenue, Singapore 639798, Singapore; (C.Z.S.); (K.F.L.)
| | - Pierre Gerard
- Groupement de Recherche de Lacq, Arkema, Route Départementale 817, BP 34, 64170 Lacq, France;
| | - Somen K. Bhudolia
- School of Mechanical and Aerospace Engineering, Nanyang Technological University, 50 Nanyang Avenue, Singapore 639798, Singapore; (C.Z.S.); (K.F.L.)
- Correspondence: (G.G.); (S.K.B.)
| |
Collapse
|
4
|
Bhudolia SK, Gohel G, Vasudevan D, Leong KF, Gerard P. Behaviour of Rectangular Hollow Thin Ply Carbon Thermoset and Thermoplastic Composite Tubes Subjected to Bending. Polymers (Basel) 2022; 14:polym14071386. [PMID: 35406259 PMCID: PMC9003124 DOI: 10.3390/polym14071386] [Citation(s) in RCA: 2] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 03/15/2022] [Revised: 03/24/2022] [Accepted: 03/26/2022] [Indexed: 11/30/2022] Open
Abstract
Tubular composites are widely used in many industrial applications, and there is need to use new material and reliable manufacturing processes to improve the performance and process aspects. The current research presents a detailed study to understand the flexure response of rectangular tubular composites based on thin ply carbon fibres and Elium® resin. Another aim was to understand the failure mechanisms of novel tubular thermoplastic composite systems and carry out a baseline comparison with Epoxy-based tubular systems. In the current research, a bladder-assisted resin transfer moulding process was used to manufacture hollow thermoplastic composite tubes, and the bending behaviour of thin ply carbon (TPC) composite parts with novel Elium® (EL) and Epoxy (EP) resin as the matrix material was studied using a detailed experimental study. A testing method with optimized support span and a saddle was used to carry out three-point bending tests on the tubular composite structures. The TPC/EL composite tubes have shown 10% higher bending strength, with a noticeable increase in deformation due the presence of extended plasticity attributes for acrylic Elium resin. Failure mechanisms studied with the detailed microscopic investigation have shown severe catastrophic failure for epoxy-based composite tubes; however, acrylic Elium®-based composite tubes have shown different damage modes such as fibre splitting, resin infragmentation, and fibre resin-interfacial cracking.
Collapse
Affiliation(s)
- Somen K. Bhudolia
- School of Mechanical and Aerospace Engineering, Nanyang Technological University, 50, Nanyang Avenue, Singapore 639798, Singapore; (G.G.); (K.F.L.)
- Correspondence:
| | - Goram Gohel
- School of Mechanical and Aerospace Engineering, Nanyang Technological University, 50, Nanyang Avenue, Singapore 639798, Singapore; (G.G.); (K.F.L.)
| | - Durga Vasudevan
- Technical University of Munich Asia, 25 International Business Park Rd, Singapore 609916, Singapore;
| | - Kah Fai Leong
- School of Mechanical and Aerospace Engineering, Nanyang Technological University, 50, Nanyang Avenue, Singapore 639798, Singapore; (G.G.); (K.F.L.)
| | - Pierre Gerard
- Groupement de Recherche de Lacq, Arkema, Route Départementale 817, BP 34, 64170 Lacq, France;
| |
Collapse
|
5
|
Bhudolia SK, Perrotey P, Gohel G, Joshi SC, Gerard P, Leong KF. Optimizing Bladder Resin Transfer Molding Process to Manufacture Complex, Thin-Ply Thermoplastic Tubular Composite Structures: An Experimental Case Study. Polymers (Basel) 2021; 13:polym13234093. [PMID: 34883597 PMCID: PMC8658802 DOI: 10.3390/polym13234093] [Citation(s) in RCA: 6] [Impact Index Per Article: 2.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 10/29/2021] [Revised: 11/17/2021] [Accepted: 11/22/2021] [Indexed: 11/24/2022] Open
Abstract
The bladder molding process is primarily used in sporting applications but mostly with prepregs. Bladder-Assisted Resin Transfer Molding (B-RTM) presents the tremendous potential to automate and mass produce the complex hollow-composite profiles. Thin-ply, non-crimp fabrics (NCFs) provide excellent mechanical, fracture toughness, and vibration damping properties on top of the weight saving it offers to a final product. However, these fiber architectures are difficult to inject due to the resistance they provide for the polymer flow using the liquid injection process. Therefore, it is mandatory to optimize the process parameters to reduce the time for injection and simultaneously achieve better consolidation. This work presents a first, detailed, experimental case study to successfully inject a low-permeability, thin-ply, complex, thermoplastic tubular structure, and the effect of process parameters, boundary conditions, the associated manufacturing challenges, and proposed solutions are deliberated in this paper.
Collapse
Affiliation(s)
- Somen K. Bhudolia
- School of Mechanical and Aerospace Engineering, Nanyang Technological University, 50 Nanyang Avenue, Singapore 639798, Singapore; (G.G.); (S.C.J.); (K.F.L.)
- Correspondence:
| | - Pavel Perrotey
- Carbon Axis, 34 Rue Jacques de Vaucanson, 17180 Perigny, France;
| | - Goram Gohel
- School of Mechanical and Aerospace Engineering, Nanyang Technological University, 50 Nanyang Avenue, Singapore 639798, Singapore; (G.G.); (S.C.J.); (K.F.L.)
| | - Sunil C. Joshi
- School of Mechanical and Aerospace Engineering, Nanyang Technological University, 50 Nanyang Avenue, Singapore 639798, Singapore; (G.G.); (S.C.J.); (K.F.L.)
| | - Pierre Gerard
- Groupement de Recherche de Lacq, Arkema Group, Route Départementale 817, 64170 Lacq, France;
| | - Kah Fai Leong
- School of Mechanical and Aerospace Engineering, Nanyang Technological University, 50 Nanyang Avenue, Singapore 639798, Singapore; (G.G.); (S.C.J.); (K.F.L.)
| |
Collapse
|
6
|
Fabrication: Mechanical Testing and Structural Simulation of Regenerated Cellulose Fabric Elium ® Thermoplastic Composite System. Polymers (Basel) 2021; 13:polym13172969. [PMID: 34503009 PMCID: PMC8434310 DOI: 10.3390/polym13172969] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.3] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 08/04/2021] [Revised: 08/27/2021] [Accepted: 08/29/2021] [Indexed: 11/29/2022] Open
Abstract
Regenerated cellulose fibres are an important part of the forest industry, and they can be used in the form of fabrics as reinforcement materials. Similar to the natural fibres (NFs), such as flax, hemp and jute, that are widely used in the automotive industry, these fibres possess good potential to be used for semi-structural applications. In this work, the mechanical properties of regenerated cellulose fabric-reinforced poly methyl methacrylate (PMMA) (Elium®) composite were investigated and compared with those of its natural fibre composite counterparts. The developed composite demonstrated higher tensile strength and ductility, as well as comparable flexural properties with those of NF-reinforced epoxy and Elium® composite systems, whereas the Young’s modulus was lower. The glass transition temperature demonstrated a value competitive (107.7 °C) with that of other NF composites. Then, the behavior of the bio-composite under bending and loading was simulated, and a materials model was used to simulate the behavior of a car door panel in a flexural scenario. Modelling can contribute to predicting the structural behavior of the bio-based thermoplastic composite for secondary applications, which is the aim of this work. Finite element simulations were performed to assess the deflection and force transfer mechanism for the car door interior.
Collapse
|
7
|
da Luz FS, Garcia Filho FDC, del-Río MTG, Nascimento LFC, Pinheiro WA, Monteiro SN. Graphene-Incorporated Natural Fiber Polymer Composites: A First Overview. Polymers (Basel) 2020; 12:polym12071601. [PMID: 32708475 PMCID: PMC7408016 DOI: 10.3390/polym12071601] [Citation(s) in RCA: 36] [Impact Index Per Article: 9.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 06/25/2020] [Revised: 07/14/2020] [Accepted: 07/14/2020] [Indexed: 11/26/2022] Open
Abstract
A novel class of graphene-based materials incorporated into natural lignocellulosic fiber (NLF) polymer composites is surging since 2011. The present overview is the first attempt to compile achievements regarding this novel class of composites both in terms of technical and scientific researches as well as development of innovative products. A brief description of the graphene nature and its recent isolation from graphite is initially presented together with the processing of its main derivatives. In particular, graphene-based materials, such as nanographene (NG), exfoliated graphene/graphite nanoplatelet (GNP), graphene oxide (GO) and reduced graphene oxide (rGO), as well as other carbon-based nanomaterials, such as carbon nanotube (CNT), are effectively being incorporated into NLF composites. Their disclosed superior mechanical, thermal, electrical, and ballistic properties are discussed in specific publications. Interfacial shear strength of 575 MPa and tensile strength of 379 MPa were attained in 1 wt % GO-jute fiber and 0.75 wt % jute fiber, respectively, epoxy composites. Moreover, a Young’s modulus of 44.4 GPa was reported for 0.75 wt % GO-jute fiber composite. An important point of interest concerning this incorporation is the fact that the amphiphilic character of graphene allows a better way to enhance the interfacial adhesion between hydrophilic NLF and hydrophobic polymer matrix. As indicated in this overview, two basic incorporation strategies have so far been adopted. In the first, NG, GNP, GO, rGO and CNT are used as hybrid filler together with NLF to reinforce polymer composites. The second one starts with GO or rGO as a coating to functionalize molecular bonding with NLF, which is then added into a polymeric matrix. Both strategies are contributing to develop innovative products for energy storage, drug release, biosensor, functional electronic clothes, medical implants, and armor for ballistic protection. As such, this first overview intends to provide a critical assessment of a surging class of composite materials and unveil successful development associated with graphene incorporated NLF polymer composites.
Collapse
Affiliation(s)
- Fernanda Santos da Luz
- Military Institute of Engineering—IME, Materials Science Program, Praça General Tibúrcio 80, Urca, Rio de Janeiro 22290-270, Brazil; (F.S.d.L.); (L.F.C.N.); (W.A.P.)
| | - Fabio da Costa Garcia Filho
- Department of Mechanical and Aerospace Engineering, University of California San Diego—UCSD, La Jolla, CA 92093-0411, USA or (F.d.C.G.F.); (M.T.G.d.-R.)
| | - Maria Teresa Gómez del-Río
- Department of Mechanical and Aerospace Engineering, University of California San Diego—UCSD, La Jolla, CA 92093-0411, USA or (F.d.C.G.F.); (M.T.G.d.-R.)
- DIMME, Grupo de Durabilidad e Integridad Mecánica de Materiales Estructurales, Universidad Rey Juan Carlos, C/Tulipán, s/n, 28933 Móstoles, Madrid, Spain
| | - Lucio Fabio Cassiano Nascimento
- Military Institute of Engineering—IME, Materials Science Program, Praça General Tibúrcio 80, Urca, Rio de Janeiro 22290-270, Brazil; (F.S.d.L.); (L.F.C.N.); (W.A.P.)
| | - Wagner Anacleto Pinheiro
- Military Institute of Engineering—IME, Materials Science Program, Praça General Tibúrcio 80, Urca, Rio de Janeiro 22290-270, Brazil; (F.S.d.L.); (L.F.C.N.); (W.A.P.)
| | - Sergio Neves Monteiro
- Military Institute of Engineering—IME, Materials Science Program, Praça General Tibúrcio 80, Urca, Rio de Janeiro 22290-270, Brazil; (F.S.d.L.); (L.F.C.N.); (W.A.P.)
- Correspondence: or
| |
Collapse
|