Electro-Oxidation-Plasma Treatment for Azo Dye Carmoisine (Acid Red 14) in an Aqueous Solution

Physical-Chemical Assessment of Azo Dye Basic Violet I (BVI) Discoloration Using the Corona Plasma in Batch and Flow Systems

The decolorization of the Basic violet I (BVI) dye when interacted with a corona discharge is studied in the present work, taking in account two systems, batch and flux. The current and voltage were measured during the whole process in which a corona plasma was generated, with an applied power of 51.9 and 167.72 W where the transport gas was air. A batch reactor and a flow reactor were used, where 500 and 5000 mL of samples were treated, respectively. Optical emission spectra (OES) were measured where the oxidizing species ·OH were at wavelengths of 307.597 and 310.148 nm, associated with the A2∑+ - X2Π transition. The absorption spectra for the batch system showed a discoloration of 85.7% in the first 10 min, while in the flow system, the absorption was 93.9% at the same time and 4.5% at the same time by conventional heating. Characteristics of the final sample included an acidic solution with an electrical conductivity of 449.20 ± 55.44 and 313.6 ± 39.58 μS/cm, a dissolved oxygen concentration of 7.74 ± 0.2 and 6.37 ± 0.23 mg/L, an absorbance of 0.04 ± 0.01 and 0.03 ± 0.01 au, with turbidity measuring 1.22 ± 1.59 and 10.34 ± 4.96 NTU, and an energy cost of 1.1 × 10-1 and 6.3 × 10-1 g/kWh in the batch and continuous flow systems, respectively. The interaction of the corona plasma with water promoted the production of reactive species, resulting in the discoloration of the Basic Violet I dye.

Decontamination of wastewater containing contaminants of emerging concern by electrooxidation and Fenton-based processes - A review on the relevance of materials and methods

In recent years, there has been an increasingly growing interest regarding the use of electrochemical advanced oxidation processes (EAOPs) which are considered highly promising alternative treatment techniques for addressing environmental issues related to pollutants of emerging concern. In EAOPs, electrogenerated oxidizing agents, such as hydroxyl radical (HO^•), can react non-selectively with a wide range of organic compounds, degrading and mineralizing their structures to unharmful molecules like CO₂, H₂O, and inorganic ions. To this date, a broad spectrum of advanced electrocatalysts have been developed and applied for the treatment of compounds of interest in different matrices, specifically aiming at enhancing the degradation performance. New combined methods have also been employed as alternative treatment techniques targeted at circumventing the major obstacles encountered in Fenton-based processes, such as high costs and energy consumption, which still contribute significantly toward inhibiting the large-scale application of these processes. First, some fundamental aspects of EAOPs will be presented. Further, we will provide an overview of electrode materials which have been recently developed and reported in the literature, highlighting different anode and cathode structures employed in EAOPs, their main advantages and disadvantages, as well as their contribution to the performance of the treatment processes. The influence of operating parameters, such as initial concentrations, pH effect, temperature, supporting electrolyte, and radiation source, on the treatment processes were also studied. Finally, hybrid techniques which have been reported in the literature and critically assess the most recent techniques used for evaluating the degradation efficiency of the treatment processes.

Electrochemical degradation of methylene blue by Pb modified porous SnO2 anode

A significant number of pollutants in wastewater can be electrocatalytically oxidized by SnO₂-Sb, a relatively inactive electrode. However, the arduous process of environmental remediation due to poor electrochemical performance and short service life of the traditional Ti/SnO₂-Sb electrode. In this work the SnO₂ electrode with a micron-sized sphere structure was prepared by in-situ hydrothermal. The results of the study that the electrode (Pb-10%) synthesized from the precursor solution in which the Pb:Sn molar ratio is 10% exhibits excellent electrooxidation properties. Impressiveing, the Pb-10% electrode displayed the small charge transfer resistance (10.71 Ω) and the high oxygen evolution potential (2.26 V vs. SCE). Thus, the electrochemical degradation experiment demonstrates that 100 mg L^-1 MB was degraded by Pb-10% electrode under the condition of initial pH = 5, and the decolorization rate reached 94.6%. Moreover, the influence of different parameters such as Pb doping amount, initial pH value of solution, initial concentration of MB and inorganic ions on degradation efficiency were also explored, in turn the practical application of electrodes in the field of purifying water resources is optimized. It is worth noting that the service life of the optimized electrode (100 mA cm^-2, 0.5 M H₂SO₄, 90 h) is about 12 times longer than that of the bare electrode (Sn-Sb). Therefore, the high-performance Ti/SnO₂-Sb electrode prepared in this work possesses vast application prospects in the electrocatalytic oxidation.

Removal of Azo Dye Carmoisine by Adsorption Process on Diatomite

This work aims to evaluate the adsorption capacity of an abundant natural diatomite (ND) to remove the azo dye carmoisine, known as a harmful emerging organic pollutant. Indeed, to the best of our knowledge, no results were reported on this subject. The ND was characterized by FTIR, XRD, and SEM/EDX analyses. The experimental study of adsorption was carried out in batch mode. Results showed that ND adsorbent is mainly composed of silica. A fraction of calcite and ankerite was also identified. It is a porous material with a specific surface of about 41 m2.g-1 and with a hydroxyl surface functional group -OH. Adsorption results showed that adsorption process on ND is found to be effective in removing the carmoisine colorant. The adsorption capacity is strongly affected by the adsorbent and adsorbate contents, the solution pH, the work temperature, and the water hardness and mineralization. At room temperature, optimal experimental conditions for the highest adsorption capacity (12 mg.g-1) were colorant concentration 50mg.L-1, pH 2, contact time 30min, and ND content 1 g.L-1. Modeling study has showed that experimental results are well modeled by the Freundlich isotherm in multilayer adsorption. The reaction kinetics are pseudo-second order, and the thermodynamic parameters indicated that the nature of the adsorption process is endothermic and spontaneous.

Recent advances in carbon nanomaterials-based electrochemical sensors for food azo dyes detection

Azo dyes as widely applied food colorants are popular for their stability and affordability. On the other hand, many of these dyes can have harmful impacts on living organs, which underscores the need to control the content of this group of dyes in food. Among the various analytical approaches for detecting the azo dyes, special attention has been paid to electro-analytical techniques for reasons such as admirable sensitivity, excellent selectivity, reproducibility, miniaturization, green nature, low cost, less time to prepare and detect of specimens and the ability to modify the electrode. Satisfactory results have been obtained so far for carbon-based nanomaterials in the fabrication of electrochemical sensing systems in detecting the levels of these materials in various specimens. The purpose of this review article is to investigate carbon nanomaterial-supported techniques for electrochemical sensing systems on the analysis of azo dyes in food samples in terms of carbon nanomaterials used, like carbon nanotubes (CNT) and grapheme (Gr).

Advances in the Application of Nanocatalysts in Photocatalytic Processes for the Treatment of Food Dyes: A Review

The use of food additives (such as dyes, which improve the appearance of the products) has become more prominent, due to the rapid population growth and the increase in demand for beverages and processed foods. The dyes are usually found in effluents that are discharged into the environment without previous treatment; this promotes mass contamination and alters the aquatic environment. In recent years, advanced oxidation processes (AOPs) have proven to be effective technologies used for wastewater treatment through the destruction of the total organic content of toxic contaminants, including food dyes. Studies have shown that the introduction of catalysts in AOPs improve treatment efficiency (i.e., complete decomposition without secondary contamination). The present review offers a quick reference for researchers, regarding the treatment of wastewater containing food dyes and the different types of AOPs, with different catalyst and nanocatalyst materials obtained from traditional and green chemical syntheses.

Bio-inspired ZnO NPs synthesized from Citrus sinensis peels extract for Congo red removal from textile wastewater via photocatalysis: Optimization, mechanisms, techno-economic analysis

Textile industry is one of the most environmental unfriendly industrial processes due to the massive generation of colored wastewater contaminated with dyes and other chemical auxiliaries. These contaminants are known to have undesirable consequences to ecosystem. The present study investigated the best operating parameters for the removal of congo red (CR, as the model for dye wastewater) by orange peels extract biosynthesized zinc oxide nanoparticles (ZnO NPs) via photocatalysis in an aqueous solution. The response surface methodology (RSM) with ZnO NPs loadings (0.05-0.20 g), pH (3.00-11.00), and initial CR concentration (5-20 ppm) were used for the optimization process. The applicability of ZnO NPs in the dye wastewater treatment was evaluated based on the techno-economic analysis (TEA). ZnO NPs exhibited hexagonal wurtzite structure with = C-H, C-O, -C-O-C, CC, O-H as the main functional groups. The maximum degradation of CR was more than 96% with 0.171 g of ZnO NPs, at pH 6.43 and 5 ppm of CR and 90% of the R² coefficient. The specific cost of ZnO NPs production is USD 20.25 per kg. These findings indicated that the biosynthesized ZnO NPs with orange peels extract provides alternative method for treating dye wastewater.

Pulsed Discharge Plasma in High-Pressure Environment for Water Pollutant Degradation and Nanoparticle Synthesis

The application of high-voltage discharge plasma for water pollutant decomposition and the synthesis of nanoparticles under a high-pressure argon gas environment (~4 MPa) was demonstrated. The experiments were carried out in a batch-type system at room temperature with a pulsed DC power supply (15.4 to 18.6 kV) as a discharge plasma source. The results showed that the electrode materials, the pulsed repetition rates, the applied number of pulses, and the applied voltages had a significant effect on the degradation reactions of organic compounds. Furthermore, carbon solid materials from glycine decomposition were generated during the high-voltage discharge plasma treatment under high-pressure conditions, while Raman spectra and the HRTEM images indicated that titanium dioxide with a brookite structure and titanium carbide nanoparticles were also formed under these conditions. It was concluded that this process is applicable in practice and may lead to advanced organic compound decomposition and metal-based nanoparticle synthesis technologies.

Assessment of the use of boron-doped diamond electrode for highly sensitive voltammetric determination of the azo-dye carmoisine E-122 in food and environmental matrices

A new protocol for the analysis of the azo-dye carmoisine (CMS) is presented by coupling differential pulse voltammetry (DPV) with a cathodically pretreated boron-doped diamond electrode (CPT-BDDE), in phosphate buffer solution (pH 2.0). The CMS presented diffusion-controlled oxidation and reduction peaks at +0.88 and -0.15 V vs Ag/AgCl, respectively. The effect of the pretreatment conditions, pH, and supporting electrolytes were evaluated to the voltammetric determination of CMS. Under optimized conditions, the differential pulse voltammetric signals for CMS were linear over the concentration range of 0.059-1.31 μmol L^-1 and 0.010-0.079 μmol L^-1 with limits of detection of 7.0 and 3.0 nmol L^-1, for the anodic and cathodic processes respectively. The method was precise for CMS determination (RSD < 5.0%) and selective against other dyes. The developed protocol was successfully applied in the analysis of CMS in surface water and foodstuffs with accurate results in comparison with those obtained using a validated spectrophotometric method.

Removal of Basic Brown 16 from Aqueous Solution Using Durian Shell Adsorbent, Optimisation and Techno-Economic Analysis

Azo dyes including C. I. Basic Brown 16 (BB16) are one of the coloured organic compounds that have adverse effects on human health and the environment. The current work aims to optimise the adsorption of C.I BB16 in aqueous solution using durian (Durio zibethinus murray) shell as a low-cost green adsorbent. Durian shell was characterised by Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). The adsorption process was optimised with response surface methodology (RSM) based on pH (4–8), time (30–240 min), durian shell dosage (0.1–1.0 g/L) and initial concentration of C.I BB16 (10–20 ppm). The removal efficiency was determined based on the reduction of chemical oxygen demand (COD) and the decolourisation of C.I BB16. The techno-economic analysis was described in the current work to know the economic feasibility of durian shells as an adsorbent. The SEM images showed that durian shell adsorbent has a smooth surface with no pores. FTIR spectra confirmed the presence of -C-O, =C–H, C=C, -C-O-C and O-H bonds in durian shell. Maximum decolourisation (77.6%) and COD removal (80.6%) for C.I BB16 was achieved with the interaction between pH, time and adsorbent dose and initial concentration of C.I BB16. The optimal operating factors for adsorption of C.I BB16 recorded at pH 8, time (30 min), durian shell dosage (1 g/L) and 15 mg /L of C.I BB16 concentrations were 77.61 vs. 74.26 (%) of C.I BB16 removal and 80.60 vs. 78.72 (%) of COD removal with an R2 coefficient of 0.94 at p < 0.05. The specific cost of durian shell coagulant production is USD 172.71 per ton which is lower than the market price of honeydew peels-activated carbon (HDP-AC) (USD 261.81) and the commercial market price of activated carbon which is USD 1000.00/tons. These findings indicated that the durian adsorbent provides alternative methods for treating hair dye wastewater. These findings indicated that durian shells have a high potential for the adsorption of C.I BB16 in aqueous solution.