1
|
Kiss L, Berényi AE, Németh M, Tegze A, Homlok R, Takács E, Mészáros L. Enhanced surface activation of ground tire rubber via the radiolysis of water for effective rubber recycling. Heliyon 2024; 10:e37454. [PMID: 39309873 PMCID: PMC11416274 DOI: 10.1016/j.heliyon.2024.e37454] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 07/12/2024] [Revised: 08/22/2024] [Accepted: 09/04/2024] [Indexed: 09/25/2024] Open
Abstract
In this study, we examined the chemical changes occurring in ground tire rubber (GTR) and on its surface as a result of gamma irradiation in water, with low doses of 5, 10, 15, 20, 25, and 30 kGy. To better distinguish the changes the radiation caused in the GTR and the surface activation of the GTR caused by the irradiated water, we also performed radiation treatments in an inert atmosphere. We mixed the treated GTRs with fresh rubber, and after vulcanization, investigated the mechanical properties and conducted dose optimization. The chemical changes occurring in GTR were characterized by Soxhlet-extraction and cross-link density measurements. Changes on the surface were investigated by Fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS). In water irradiation, cross-link density decreased (∼10 %), while in an inert atmosphere, new bonds formed between the chains (∼10 %), with negligible degradation (∼2 %) in both cases. Based on the FTIR spectra, new oxygen-containing groups appeared on the GTR surface in water treatment, while this was not observed in a nitrogen atmosphere. The increase in surface oxygen content was confirmed by XPS, showing a ∼10 % increase as a result of water treatment, while it remained unchanged in the inert atmosphere. We achieved a 30 % increase in tensile strength (5 kGy) without a decrease in elongation properties and a 32 % increase in tear strength (20 kGy) for vulcanizates containing surface-activated GTR. Mechanical properties did not improve with treatments in an inert atmosphere. The oxidizing agents formed during the radiolysis of water activated the surface of the GTR, helping to establish a better connection with the matrix.
Collapse
Affiliation(s)
- Lóránt Kiss
- Department of Polymer Engineering, Faculty of Mechanical Engineering, Budapest University of Technology and Economics, Műegyetem rkp. 3., H-1111 Budapest, Hungary
| | - Alexandra Erzsébet Berényi
- Department of Polymer Engineering, Faculty of Mechanical Engineering, Budapest University of Technology and Economics, Műegyetem rkp. 3., H-1111 Budapest, Hungary
| | - Miklós Németh
- Department of Surface Chemistry and Catalysis, Institute for Energy Security and Environmental Safety, HUN-REN Centre for Energy Research, Konkoly-Thege M. street 29-33, H-1121 Budapest, Hungary
| | - Anna Tegze
- Radiation Chemistry Department, Institute for Energy Security and Environmental Safety, HUN-REN Centre for Energy Research, Konkoly-Thege M. street 29-33, H-1121 Budapest, Hungary
| | - Renáta Homlok
- Radiation Chemistry Department, Institute for Energy Security and Environmental Safety, HUN-REN Centre for Energy Research, Konkoly-Thege M. street 29-33, H-1121 Budapest, Hungary
| | - Erzsébet Takács
- Radiation Chemistry Department, Institute for Energy Security and Environmental Safety, HUN-REN Centre for Energy Research, Konkoly-Thege M. street 29-33, H-1121 Budapest, Hungary
| | - László Mészáros
- Department of Polymer Engineering, Faculty of Mechanical Engineering, Budapest University of Technology and Economics, Műegyetem rkp. 3., H-1111 Budapest, Hungary
- HUN-REN-BME Research Group for Composite Science and Technology, Műegyetem rkp. 3., H-1111 Budapest, Hungary
| |
Collapse
|
2
|
Hejna A, Kosmela P, Olszewski A, Zedler Ł, Formela K, Skórczewska K, Piasecki A, Marć M, Barczewski R, Barczewski M. Management of ground tire rubber waste by incorporation into polyurethane-based composite foams. ENVIRONMENTAL SCIENCE AND POLLUTION RESEARCH INTERNATIONAL 2024; 31:17591-17616. [PMID: 36701051 PMCID: PMC10923751 DOI: 10.1007/s11356-023-25387-w] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Grants] [Track Full Text] [Subscribe] [Scholar Register] [Received: 11/03/2022] [Accepted: 01/14/2023] [Indexed: 06/17/2023]
Abstract
Rapid economic growth implicated the developing multiple industry sectors, including the automotive branch, increasing waste generation since recycling and utilization methods have not been established simultaneously. A very severe threat is the generation of enormous amounts of post-consumer tires considered burdensome waste, e.g., due to the substantial emissions of volatile organic compounds (VOCs). Therefore, it is essential to develop novel, environmentally friendly methods for their utilization, which would hinder their environmental impacts. One of the most promising approaches is shredding, resulting in the generation of ground tire rubber (GTR), which can be introduced into polymeric materials as filler. The presented work is related to the thermomechanical treatment of GTR in a twin-screw extruder with zinc borate, whose incorporation is aimed to enhance shear forces within the extruder barrel. Modified GTR was introduced into flexible polyurethane (PU) foams, and the impact of modification parameters on the cellular structure, static and dynamic mechanical performance, thermal stability, as well as thermal insulation, and acoustic properties was investigated. Emissions of VOCs from applied fillers and prepared composites were monitored and evaluated. Depending on the treatment parameters, beneficial changes in foams' cellular structure were noted, which enhanced their thermal insulation performance, mechanical strength, and thermal stability. It was proven that the proposed method of GTR thermomechanical treatment assisted by zinc borate particles might benefit the performance of flexible PU foamed composites and hinder VOC emissions, which could broaden the application range of GTR and provide novel ways for its efficient utilization.
Collapse
Affiliation(s)
- Aleksander Hejna
- Institute of Materials Technology, Poznan University of Technology, Piotrowo 3, 60-965, Poznań, Poland.
- Department of Polymer Technology, Gdańsk University of Technology, Narutowicza 11/12, 80-233, Gdańsk, Poland.
| | - Paulina Kosmela
- Department of Polymer Technology, Gdańsk University of Technology, Narutowicza 11/12, 80-233, Gdańsk, Poland
| | - Adam Olszewski
- Department of Polymer Technology, Gdańsk University of Technology, Narutowicza 11/12, 80-233, Gdańsk, Poland
| | - Łukasz Zedler
- Department of Molecular Biotechnology and Microbiology, Gdańsk University of Technology, Narutowicza 11/12, 80-233, Gdańsk, Poland
| | - Krzysztof Formela
- Department of Polymer Technology, Gdańsk University of Technology, Narutowicza 11/12, 80-233, Gdańsk, Poland
| | - Katarzyna Skórczewska
- Department of Polymer Technology, Bydgoszcz University of Science and Technology, 85-326, Bydgoszcz, Poland
| | - Adam Piasecki
- Institute of Materials Engineering, Poznan University of Technology, Jana Pawła II 24, 60-965, Poznań, Poland
| | - Mariusz Marć
- Department of Analytical Chemistry, Gdańsk University of Technology, Narutowicza 11/12, 80-233, Gdańsk, Poland
| | - Roman Barczewski
- Institute of Applied Mechanics, Poznan University of Technology, Jana Pawła II 24, 60-965, Poznań, Poland
| | - Mateusz Barczewski
- Institute of Materials Technology, Poznan University of Technology, Piotrowo 3, 60-965, Poznań, Poland
| |
Collapse
|
3
|
Kairytė A, Šeputytė-Jucikė J, Członka S, Vėjelis S, Vaitkus S. Impact of Different Ratios of Lignin Waste and Liquid Glass on the Performance Characteristics of Biopolyurethane Foams. Polymers (Basel) 2023; 15:polym15040818. [PMID: 36850102 PMCID: PMC9959299 DOI: 10.3390/polym15040818] [Citation(s) in RCA: 1] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 01/16/2023] [Revised: 02/01/2023] [Accepted: 02/02/2023] [Indexed: 02/10/2023] Open
Abstract
In the current study, biopolyurethane foam was modified with 2.5-10 wt.% lignin waste (LigW) and liquid glass (LG)-modified LigW particles at different LigW/LG ratios-1:1 and 1:2-and their impact on performance characteristics-i.e., rheology, foaming times, apparent density, thermal conductivity before and after aging, dimensional stability at ambient and elevated conditions, compressive and tensile strengths, short-term water absorption by partial immersion, and water vapor permeability-was determined and evaluated. Structural analysis was implemented and structural parameters were taken into consideration as well. During the study, it was determined that 2.5-10 wt.% particles at the LigW/LG ratio of 1:2 showed a superior impact on the physical and mechanical properties of bioPUR foams. The apparent density only insignificantly increased and was in a density range suitable for commercially available polyurethanes. For particles at 10 wt.% and LigW/LG ratio of 1:1, the thermal conductivity value improved by 3.2%, the compressive strength increased by 153%, while the tensile strength improved by 23.5%, indicating sufficient interfacial adhesion between the filler and polymer matrix. Moreover, the short-term water absorption by partial immersion remained almost unchanged, while the water vapour diffusion resistance factor improved from 43 to 48. Additionally, the incorporation of LigW/LG 1:1 and LigW/LG 1:2 particles made it possible to obtain dimensionally and structurally stable closed-cell bioPUR foams for possible application as thermal insulation in building envelopes.
Collapse
Affiliation(s)
- Agnė Kairytė
- Laboratory of Thermal Insulating Materials and Acoustics, Institute of Building Materials, Faculty of Civil Engineering, Vilnius Gediminas Technical University, Linkmenų st. 28, 08217 Vilnius, Lithuania
- Correspondence:
| | - Jurga Šeputytė-Jucikė
- Laboratory of Thermal Insulating Materials and Acoustics, Institute of Building Materials, Faculty of Civil Engineering, Vilnius Gediminas Technical University, Linkmenų st. 28, 08217 Vilnius, Lithuania
| | - Sylwia Członka
- Institute of Polymer & Dye Technology, Lodz University of Technology, 90-924 Lodz, Poland
| | - Sigitas Vėjelis
- Laboratory of Thermal Insulating Materials and Acoustics, Institute of Building Materials, Faculty of Civil Engineering, Vilnius Gediminas Technical University, Linkmenų st. 28, 08217 Vilnius, Lithuania
| | - Saulius Vaitkus
- Laboratory of Thermal Insulating Materials and Acoustics, Institute of Building Materials, Faculty of Civil Engineering, Vilnius Gediminas Technical University, Linkmenų st. 28, 08217 Vilnius, Lithuania
| |
Collapse
|
4
|
Kowalczyk Ł, Korol J, Chmielnicki B, Laska A, Chuchala D, Hejna A. One More Step towards a Circular Economy for Thermal Insulation Materials-Development of Composites Highly Filled with Waste Polyurethane (PU) Foam for Potential Use in the Building Industry. MATERIALS (BASEL, SWITZERLAND) 2023; 16:782. [PMID: 36676519 PMCID: PMC9864609 DOI: 10.3390/ma16020782] [Citation(s) in RCA: 1] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Figures] [Subscribe] [Scholar Register] [Received: 12/19/2022] [Revised: 01/04/2023] [Accepted: 01/11/2023] [Indexed: 06/17/2023]
Abstract
The rapid development of the building sector has created increased demand for novel materials and technologies, while on the other hand resulting in the generation of a severe amount of waste materials. Among these are polyurethane (PU) foams, which are commonly applied as thermal insulation materials. Their management is a serious industrial problem, due to, for example, their complex chemical composition. Although some chemical and thermochemical methods of PU foam recycling are known, their broader use is limited due to requirements related to the complexity and safety of their installation, thus implicating high costs. Therefore, material recycling poses a promising alternative. The incorporation of waste PU foams as fillers for polymer composites could make it possible to take advantage of their structure and performance. Herein, polypropylene-based composites that were highly filled with waste PU foam and modified using foaming agents were prepared and analyzed. Depending on the foam loading and the foaming agent applied, the apparent density of material was reduced by as much as 68%. The efficient development of a porous structure, confirmed by scanning electron microscopy and high-resolution computed micro-tomography, enabled a 64% decrease in the thermal conductivity coefficient. The foaming of the structure affected the mechanical performance of composites, resulting in a deterioration of their tensile and compressive performance. Therefore, developing samples of the analyzed composites with the desired performance would require identifying the proper balance between mechanical strength and economic, as well as ecological (share of waste material in composite, apparent density of material), considerations.
Collapse
Affiliation(s)
- Łukasz Kowalczyk
- Central Mining Institute, Department of Material Engineering, Pl. Gwarkow 1, 40-166 Katowice, Poland
| | - Jerzy Korol
- Central Mining Institute, Department of Material Engineering, Pl. Gwarkow 1, 40-166 Katowice, Poland
| | - Błażej Chmielnicki
- Łukasiewicz Research Network–Institute of Engineering of Polymer Materials and Dyes, Center for Paints and Plastics, ul. Chorzowska 50A, 44-100 Gliwice, Poland
| | - Aleksandra Laska
- Faculty of Mechanical Engineering and Ship Technology and EkoTech Center, Gdańsk University of Technology, 80-233 Gdańsk, Poland
| | - Daniel Chuchala
- Faculty of Mechanical Engineering and Ship Technology and EkoTech Center, Gdańsk University of Technology, 80-233 Gdańsk, Poland
| | - Aleksander Hejna
- Institute of Materials Technology, Poznan University of Technology, Piotrowo 3, 60-965 Poznań, Poland
| |
Collapse
|
5
|
The Impact of Isocyanate Index and Filler Functionalities on the Performance of Flexible Foamed Polyurethane/Ground Tire Rubber Composites. Polymers (Basel) 2022; 14:polym14245558. [PMID: 36559925 PMCID: PMC9781178 DOI: 10.3390/polym14245558] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 11/22/2022] [Revised: 12/13/2022] [Accepted: 12/16/2022] [Indexed: 12/23/2022] Open
Abstract
The structure and performance of polyurethane (PU) foams are strongly driven by the stoichiometry of the polyaddition reaction, quantitatively described by the isocyanate index. It determines the balance between isocyanate and hydroxyl groups in the reacting system and is affected by the introduction of additional functionalities originated, e.g., from applied fillers. Nevertheless, this issue is hardly taken into account in research works. Herein, the structure and performance of PU/ground tire rubber (GTR) composites differing in their isocyanate index (from 0.8 to 1.2) and prepared with and without considering the GTR functionalities in formulation development were investigated. Incorporating GTR into the PU matrix led to a reduction in average cell diameter (from 2 to 30% depending on the isocyanate index) compared to unfilled foams. However, formulation adjustments did not show a significant impact on cellular structure. The only decrease in open cell content was noted, from 10% for the 0.9 index to 40% for 1.2. Such changes were related to the increasing strength of the PU cellular structure able to maintain inside the increasing amount of carbon dioxide. On the other hand, considering hydroxyl values of GTR noticeably affected the thermomechanical performance of composites. The shift of glass transition temperature (Tg), even by 10 °C for 1.2 isocyanate index, enhanced the performance of materials, which was expressed in an 8-62% drop in the composite performance factor, pointing to the enhanced reinforcing effect resulting from filler incorporation. The stiffening of foams, related to the variations in PU segmental structure, also caused minor changes in the course of thermal degradation of PU/GTR composites due to the inferior thermal stability of hard segments. The obtained results provide important insights into the development of formulations of PU composites filled with materials containing reactive functional groups able to disrupt the stoichiometric balance of the polyaddition reaction.
Collapse
|
6
|
Olszewski A, Kosmela P, Żukowska W, Wojtasz P, Szczepański M, Barczewski M, Zedler Ł, Formela K, Hejna A. Insights into Stoichiometry Adjustments Governing the Performance of Flexible Foamed Polyurethane/Ground Tire Rubber Composites. Polymers (Basel) 2022; 14:polym14183838. [PMID: 36145981 PMCID: PMC9503757 DOI: 10.3390/polym14183838] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.5] [Reference Citation Analysis] [Abstract] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 08/18/2022] [Revised: 09/07/2022] [Accepted: 09/09/2022] [Indexed: 11/16/2022] Open
Abstract
Polyurethanes (PU) are widely applied in the industry due to their tunable performance adjusted by changes in the isocyanate index—stoichiometric balance between isocyanate and hydroxyl groups. This balance is affected by the incorporation of modifiers of fillers into the PU matrix and is especially crucial for PU foams due to the additional role of isocyanates—foaming of the material. Despite the awareness of the issue underlined in research works, the contribution of additives into formulations is often omitted, adversely impacting foams’ performance. Herein, flexible foamed PU/ground tire rubber (GTR) composites containing 12 different types of modified GTR particles differing by hydroxyl value (LOH) (from 45.05 to 88.49 mg KOH/g) were prepared. The impact of GTR functionalities on the mechanical, thermomechanical, and thermal performance of composites prepared with and without considering the LOH of fillers was assessed. Formulation adjustments induced changes in tensile strength (92–218% of the initial value), elongation at break (78–100%), tensile toughness (100–185%), compressive strength (156–343%), and compressive toughness (166–310%) proportional to the shift of glass transition temperatures (3.4–12.3 °C) caused by the additional isocyanates’ reactions yielding structure stiffening. On the other hand, formulation adjustments reduced composites’ thermal degradation onset due to the inferior thermal stability of hard segments compared to soft segments. Generally, changes in the composites’ performance resulting from formulation adjustments were proportional to the hydroxyl values of GTR, justifying the applied approach.
Collapse
Affiliation(s)
- Adam Olszewski
- Department of Polymer Technology, Gdańsk University of Technology, Narutowicza 11/12, 80-233 Gdańsk, Poland
| | - Paulina Kosmela
- Department of Polymer Technology, Gdańsk University of Technology, Narutowicza 11/12, 80-233 Gdańsk, Poland
| | - Wiktoria Żukowska
- Department of Polymer Technology, Gdańsk University of Technology, Narutowicza 11/12, 80-233 Gdańsk, Poland
| | - Paweł Wojtasz
- Department of Polymer Technology, Gdańsk University of Technology, Narutowicza 11/12, 80-233 Gdańsk, Poland
| | - Mariusz Szczepański
- Department of Polymer Technology, Gdańsk University of Technology, Narutowicza 11/12, 80-233 Gdańsk, Poland
| | - Mateusz Barczewski
- Institute of Materials Technology, Poznan University of Technology, Piotrowo 3, 61-138 Poznan, Poland
| | - Łukasz Zedler
- Department of Molecular Biotechnology and Microbiology, Gdańsk University of Technology, Narutowicza 11/12, 80-233 Gdańsk, Poland
| | - Krzysztof Formela
- Department of Polymer Technology, Gdańsk University of Technology, Narutowicza 11/12, 80-233 Gdańsk, Poland
| | - Aleksander Hejna
- Department of Polymer Technology, Gdańsk University of Technology, Narutowicza 11/12, 80-233 Gdańsk, Poland
- Correspondence:
| |
Collapse
|
7
|
Comprehensive Investigation of Stoichiometry–Structure–Performance Relationships in Flexible Polyurethane Foams. Polymers (Basel) 2022; 14:polym14183813. [PMID: 36145957 PMCID: PMC9501594 DOI: 10.3390/polym14183813] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 07/21/2022] [Revised: 09/02/2022] [Accepted: 09/09/2022] [Indexed: 11/17/2022] Open
Abstract
Polyurethane (PU) foams are versatile materials with a broad application range. Their performance is driven by the stoichiometry of polymerization reaction, which has been investigated in several works. However, the analysis was often limited only to selected properties and compared samples differing in apparent density, significantly influencing their performance. In the bigger picture, there is still a lack of comprehensive studies dealing with the stoichiometry impact on PU foams’ performance. Herein, flexible PU foams with a similar apparent density but differing in the isocyanate index (IIso) (from 0.80 to 1.20) were prepared. The stoichiometry–structure–performance relationships were investigated considering cellular and chemical structure, as well as the static and dynamic mechanical properties, thermal stability, thermal insulation, and acoustic performance. For IIso of 1.00, the biggest cell diameters of 274 µm were noted, which was 21–25% higher compared to 0.80 and 1.20 values. Increasing IIso reduced open cell content from 83.1 to 22.4%, which, combined with stiffening of structure (rise of modulus from 63 to 2787 kPa) resulting from crosslinking, limited the sound suppression ability around five times. On the other hand, it significantly strengthened the material, increasing tensile and compressive strength 4 and 13 times, respectively. Changes in the foams’ performance were also induced by the glass transition temperature shift from 6.1 to 31.7 °C, resulting from a greater extent of urethane groups’ generation and additional isocyanate reactions. Generally, the presented work provides important insights into preparing flexible PU foams and could be very useful for the future development of these materials.
Collapse
|
8
|
Żukowska W, Kosmela P, Wojtasz P, Szczepański M, Piasecki A, Barczewski R, Barczewski M, Hejna A. Comprehensive Enhancement of Prepolymer-Based Flexible Polyurethane Foams' Performance by Introduction of Cost-Effective Waste-Based Ground Tire Rubber Particles. MATERIALS (BASEL, SWITZERLAND) 2022; 15:ma15165728. [PMID: 36013863 PMCID: PMC9412428 DOI: 10.3390/ma15165728] [Citation(s) in RCA: 4] [Impact Index Per Article: 2.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Received: 07/22/2022] [Revised: 08/13/2022] [Accepted: 08/18/2022] [Indexed: 05/11/2023]
Abstract
Material innovations in polyurethane (PU) foams should ideally combine performance enhancement, environmental impact limitation, and cost reduction. These goals can be achieved by applying recycled or waste-based materials without broader industrial applications, implicating their low price. Herein, from 5 to 20 parts by weight of ground tire rubber (GTR) particles originated from the recycling of postconsumer car tires were incorporated into a flexible foamed PU matrix as a cost-effective waste-based filler. A two-step prepolymer method of foams manufacturing was applied to maximize the potential of applied formulation changes. The impact of the GTR content on the foams' processing, chemical, and cellular structure, as well as static and dynamic mechanical properties, thermal stability, sound suppression ability, and thermal insulation performance, was investigated. The introduction of GTR caused a beneficial reduction in the average cell diameter, from 263.1 µm to 144.8-188.5 µm, implicating a 1.0-4.3% decrease in the thermal conductivity coefficient. Moreover, due to the excellent mechanical performance of the car tires-the primary application of GTR-the tensile performance of the foams was enhanced despite the disruption of the cellular structure resulting from the competitiveness between the hydroxyl groups of the applied polyols and on the surface of the GTR particles. The tensile strength and elongation at break were increased by 10 and 8% for 20 parts by weight GTR addition. Generally, the presented work indicates that GTR can be efficiently applied as a filler for flexible PU foams, which could simultaneously enhance their performance, reduce costs, and limit environmental impacts due to the application of waste-based material.
Collapse
Affiliation(s)
- Wiktoria Żukowska
- Department of Polymer Technology, Gdańsk University of Technology, Narutowicza 11/12, 80-233 Gdańsk, Poland
| | - Paulina Kosmela
- Department of Polymer Technology, Gdańsk University of Technology, Narutowicza 11/12, 80-233 Gdańsk, Poland
| | - Paweł Wojtasz
- Department of Polymer Technology, Gdańsk University of Technology, Narutowicza 11/12, 80-233 Gdańsk, Poland
| | - Mariusz Szczepański
- Department of Polymer Technology, Gdańsk University of Technology, Narutowicza 11/12, 80-233 Gdańsk, Poland
| | - Adam Piasecki
- Institute of Materials Engineering, Poznan University of Technology, Jana Pawła II 24, 60-965 Poznan, Poland
| | - Roman Barczewski
- Institute of Applied Mechanics, Poznan University of Technology, Jana Pawła II 24, 60-965 Poznan, Poland
| | - Mateusz Barczewski
- Institute of Materials Technology, Poznan University of Technology, Piotrowo 3, 61-138 Poznan, Poland
| | - Aleksander Hejna
- Department of Polymer Technology, Gdańsk University of Technology, Narutowicza 11/12, 80-233 Gdańsk, Poland
- Correspondence:
| |
Collapse
|
9
|
Fazli A, Rodrigue D. Thermoplastic Elastomer based on Recycled HDPE/Ground Tire Rubber Interfacially Modified with an Elastomer: Effect of Mixing Sequence and Elastomer Type/Content. POLYM-PLAST TECH MAT 2022. [DOI: 10.1080/25740881.2022.2033770] [Citation(s) in RCA: 2] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 03/17/2023]
Affiliation(s)
- Ali Fazli
- Department of Chemical Engineering, Université Laval, Quebec, QC, Canada
| | - Denis Rodrigue
- Department of Chemical Engineering, Université Laval, Quebec, QC, Canada
| |
Collapse
|
10
|
Wei L, Xin Z. The effect of ground tire rubber modified by deep eutectic solvents on the viscoelasticity of silica‐filled styrene‐butadiene rubber. POLYM ENG SCI 2022. [DOI: 10.1002/pen.25956] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.5] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 01/31/2023]
Affiliation(s)
- Liping Wei
- Key Laboratory of Rubber‐Plastics, Ministry of Education/Shandong Provincial Key Laboratory of Rubber‐Plastics School of Polymer Science and Engineering, Qingdao University of Science and Technology Qingdao China
| | - Zhenxiang Xin
- Key Laboratory of Rubber‐Plastics, Ministry of Education/Shandong Provincial Key Laboratory of Rubber‐Plastics School of Polymer Science and Engineering, Qingdao University of Science and Technology Qingdao China
| |
Collapse
|
11
|
DEMİREL MH, AYDOĞMUŞ E. Waste Polyurethane Reinforced Polyester Composite, Production, and Characterization. JOURNAL OF THE TURKISH CHEMICAL SOCIETY, SECTION A: CHEMISTRY 2022. [DOI: 10.18596/jotcsa.937332] [Citation(s) in RCA: 2] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/05/2022] Open
|
12
|
Recent Advances in Development of Waste-Based Polymer Materials: A Review. Polymers (Basel) 2022; 14:polym14051050. [PMID: 35267873 PMCID: PMC8914771 DOI: 10.3390/polym14051050] [Citation(s) in RCA: 10] [Impact Index Per Article: 5.0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 12/24/2021] [Revised: 02/04/2022] [Accepted: 03/01/2022] [Indexed: 11/16/2022] Open
Abstract
Limited petroleum sources, suitable law regulations, and higher awareness within society has caused sustainable development of manufacturing and recycling of polymer blends and composites to be gaining increasing attention. This work aims to report recent advances in the manufacturing of environmentally friendly and low-cost polymer materials based on post-production and post-consumer wastes. Sustainable development of three groups of materials: wood polymer composites, polyurethane foams, and rubber recycling products were comprehensively described. Special attention was focused on examples of industrially applicable technologies developed in Poland over the last five years. Moreover, current trends and limitations in the future “green” development of waste-based polymer materials were also discussed.
Collapse
|
13
|
Dimeric Histidine as a Novel Free Radical Scavenger Alleviates Non-Alcoholic Liver Injury. Antioxidants (Basel) 2021; 10:antiox10101529. [PMID: 34679664 PMCID: PMC8532998 DOI: 10.3390/antiox10101529] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.3] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 08/21/2021] [Revised: 09/22/2021] [Accepted: 09/24/2021] [Indexed: 01/20/2023] Open
Abstract
Non-alcoholic liver injury (NLI) is a common disease worldwide. Since free radical damage in the liver is a crucial initiator leading to diseases, scavenging excess free radicals has become an essential therapeutic strategy. To enhance the antioxidant capacity of histidine, we synthesized a protonated dimeric histidine, H-bihistidine, and investigated its anti-free radical potential in several free-radical-induced NLI. Results showed that H-bihistidine could strongly scavenge free radicals caused by H2O2, fatty acid, and CCl4, respectively, and recover cell viability in cultured hepatocytes. In the animal model of nonalcoholic fatty liver injury caused by high-fat diet, H-bihistidine reduced the contents of transaminases and lipids in serum, eliminated the liver’s fat accumulation, and decreased the oxidative damage. Moreover, H-bihistidine could rescue CCl4-induced liver injury and recover energy supply through scavenging free radicals. Moreover, liver fibrosis prepared by high-fat diet and CCl4 administration was significantly alleviated after H-bihistidine treatment. This study suggests a novel nonenzymatic free radical scavenger against NLI and, potentially, other free-radical-induced diseases.
Collapse
|
14
|
Hejna A. Clays as Inhibitors of Polyurethane Foams' Flammability. MATERIALS (BASEL, SWITZERLAND) 2021; 14:4826. [PMID: 34500914 PMCID: PMC8432671 DOI: 10.3390/ma14174826] [Citation(s) in RCA: 6] [Impact Index Per Article: 2.0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Download PDF] [Figures] [Subscribe] [Scholar Register] [Received: 07/29/2021] [Revised: 08/20/2021] [Accepted: 08/24/2021] [Indexed: 11/22/2022]
Abstract
Polyurethanes are a very important group of polymers with an extensive range of applications in different branches of industry. In the form of foams, they are mainly used in bedding, furniture, building, construction, and automotive sectors. Due to human safety reasons, these applications require an appropriate level of flame retardance, often required by various law regulations. Nevertheless, without the proper modifications, polyurethane foams are easily ignitable, highly flammable, and generate an enormous amount of smoke during combustion. Therefore, proper modifications or additives should be introduced to reduce their flammability. Except for the most popular phosphorus-, halogen-, or nitrogen-containing flame retardants, promising results were noted for the application of clays. Due to their small particle size and flake-like shape, they induce a "labyrinth effect" inside the foam, resulting in the delay of decomposition onset, reduction of smoke generation, and inhibition of heat, gas, and mass transfer. Moreover, clays can be easily modified with different organic compounds or used along with conventional flame retardants. Such an approach may often result in the synergy effect, which provides the exceptional reduction of foams' flammability. This paper summarizes the literature reports related to the applications of clays in the reduction of polyurethane foams' flammability, either by their incorporation as a nanofiller or by preparation of coatings.
Collapse
Affiliation(s)
- Aleksander Hejna
- Department of Polymer Technology, Gdańsk University of Technology, Narutowicza 11/12, 80-233 Gdańsk, Poland
| |
Collapse
|
15
|
Synthesis and Physicochemical Characteristics of Chitosan-Based Polyurethane Flexible Foams. Processes (Basel) 2021. [DOI: 10.3390/pr9081394] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.3] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/16/2022] Open
Abstract
The use of shrimp waste to obtain chitosan (Ch) is an essential issue, considering a circular economy, waste management, and its application to environmentally friendly materials. In this study, northern prawn shells were utilized to obtain Ch, which could then be used for synthesizing chitosan-based polyurethane (PUR+Ch) foams with different Ch concentration. The chemical structure, morphology, hardness, thermal properties, viscoelastic properties, and sorption properties in relation to oil and water of these materials were determined. The results present that the addition of Ch into PUR influences the physicochemical characteristics and properties of the tested materials. PUR+Ch foams with 1–3 wt% Ch had more open cells and were softer than neat PUR. PUR+Ch1 had the best thermal properties. PUR+Ch2 foam with 2 wt% Ch as a whole was characterized as having the highest water sorption. The PUR+Ch1 foam with 1 wt% Ch had the best oil sorption. This paper shows that the modification of PUR by Ch is a very promising solution, and PUR+Ch foams can be applied in the water treatment of oil spills, which can be dangerous to the water environment.
Collapse
|
16
|
Ground Tire Rubber Filled Flexible Polyurethane Foam-Effect of Waste Rubber Treatment on Composite Performance. MATERIALS 2021; 14:ma14143807. [PMID: 34300726 PMCID: PMC8304020 DOI: 10.3390/ma14143807] [Citation(s) in RCA: 7] [Impact Index Per Article: 2.3] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Subscribe] [Scholar Register] [Received: 05/11/2021] [Revised: 06/24/2021] [Accepted: 07/06/2021] [Indexed: 12/16/2022]
Abstract
The application range of flexible polyurethane (PU) foams is comprehensive because of their versatility and flexibility in adjusting structure and performance. In addition to the investigations associated with further broadening of their potential properties, researchers are looking for new raw materials, beneficially originated from renewable resources or recycling. A great example of such a material is ground tire rubber (GTR)—the product of the material recycling of post-consumer car tires. To fully exploit the benefits of this material, it should be modified to enhance the interfacial interactions between PU and GTR. In the presented work, GTR particles were thermo-mechanically modified with the addition of fresh and waste rapeseed oil in the reactive extrusion process. The introduction of modified GTR particles into a flexible PU matrix caused a beneficial 17–28% decrease in average cell diameters. Such an effect caused an even 5% drop in thermal conductivity coefficient values, enhancing thermal insulation performance. The application of waste oil resulted in the superior mechanical performance of composites compared to the fresh one and thermo-mechanical modification without oils. The compressive and tensile performance of composites filled with waste oil-modified GTR was almost the same as for the unfilled foam. Moreover, the introduction of ground tire rubber particles enhanced the thermal stability of neat polyurethane foam.
Collapse
|
17
|
Structural Changes and Their Implications in Foamed Flexible Polyurethane Composites Filled with Rapeseed Oil-Treated Ground Tire Rubber. JOURNAL OF COMPOSITES SCIENCE 2021. [DOI: 10.3390/jcs5030090] [Citation(s) in RCA: 5] [Impact Index Per Article: 1.7] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 11/16/2022]
Abstract
The utilization of post-consumer car tires is an essential issue from an ecological and economic point of view. One of the simplest and the least harmful methods is their material recycling resulting in ground tire rubber (GTR), which can be further applied as fillers for polymer-based composites. Nevertheless, insufficient interfacial interactions implicate the necessity of GTR modification before introduction into polymer matrices. In this study, we investigated the influence of rapeseed oil-assisted thermo-mechanical treatment of GTR using a reactive extrusion process on the processing, structure, and performance of flexible polyurethane/GTR composite foams. Applied modifications affected the processing of polyurethane systems. They caused a noticeable reduction in the average cell size of foams, which was attributed to the potential nucleating activity of solid particles and changes in surface tension caused by the presence of oil. Such an effect was especially pronounced for the waste rapeseed oil, which resulted in the highest content of closed cells. Structural changes caused by GTR modification implicated the enhancement of foams’ strength. Mechanical performance was significantly affected by the applied modifications due to the changes in glass transition temperature. Moreover, the incorporation of waste GTR particles into the polyurethane matrix noticeably improved its thermal stability.
Collapse
|
18
|
Special Issue: Structure, Properties and Applications of Polymeric Foams. MATERIALS 2021; 14:ma14061474. [PMID: 33802980 PMCID: PMC8002667 DOI: 10.3390/ma14061474] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Download PDF] [Subscribe] [Scholar Register] [Received: 03/08/2021] [Accepted: 03/16/2021] [Indexed: 11/30/2022]
|