Virus Inactivation in Water Using Laser-Induced Graphene Filters

Iron Nanoparticle-Incorporated Laser-Induced Graphene Filters for Environmental Remediation via an In Situ Electro-Fenton Process

Laser-induced graphene (LIG) has garnered much attention due to its facile and chemically free fabrication technique. Metal nanoparticle incorporation into the LIG matrix can improve its electrical and catalytical properties for environmental application. Here, we demonstrate the fabrication of nanoscale zerovalent iron (nZVI) nanoparticle-incorporated LIG (Fe-LIG) and sulfidized-nanoscale zerovalent iron (S-nZVI) nanoparticle-incorporated LIG (SFe-LIG) surfaces. The sheets were first fabricated to investigate nanoparticle loading, successful incorporation in the LIG matrix, and electrochemical performance as electrodes. Fe-LIG and SFe-LIG sheets showed ∼3-3.5 times more charge density as compared with the control LIG sheet. The XPS and its deconvolution confirmed the presence of nZVI and S-nZVI in the Fe-LIG and SFe-LIG surfaces, which can generate in situ hydroxyl radical (•OH) via iron activation of electrogenerated hydrogen peroxide (H2O2) in short in situ electro-Fenton process. After confirmation of the successful incorporation of iron-based nanoparticles in the LIG matrix, filters were fabricated to demonstrate the application in the flow-through filtration. The Fe-LIG and SFe-LIG filters showed ∼10-30% enhanced methylene blue removal under the application of 2.5 V at ∼1000 LMH flux. The Fe-LIG and SFe-LIG filters also showed complete 6-log bacteria and virus removal at 2.5 and 5 V, respectively, while the LIG filters showed only ∼4-log removal. Such enhanced removal by the Fe-LIG and SFe-LIG filters as compared to LIG filters is attributed to the improved charge density, electrochemical activity, and in situ electro-Fenton process. The study shows the potential to develop catalytic LIG-based surfaces for various applications, including contaminant removal and microbial inactivation.

Solar interfacial evaporation devices for desalination and water treatment: Perspective and future

Water is an essential commodity for society, and alternate resources such as seawater and wastewater are vital for the future. There are various desalination technologies that can provide sufficient and sustainable water sources. Renewable energy-based desalination technologies like solar-based interfacial evaporation are very efficient and sustainable desalination methods. Solar-based interfacial evaporation has been a focus due to its efficient and easy-to-use methods. Still, research is needed for fouling resistance, scalable and low-cost materials, and devices for solar interfacial evaporation. Recent research focuses on the materials for evaporation devices, but various other aspects of device design and fabrication methods are also necessary to improve device performance. In this article, all the evaporator device configurations and strategies for efficient evaporator devices are compiled and summarized. The evaporator devices have been classified into eight main categories: monolayer, bilayer, tree-like design, low-temperature designs, 3D-Origami-based designs, latent heat recovery design, design with storage/batch process, and contactless design. It was found that a good absorber, well-engineered air-water interface, and bottom-layer insulation are necessary for the best systems. The current research focuses on the vapor production output of the devices but not on the water production from devices. So, the focus on device-based water production and the associated cost of the water produced is essential. This article articulates the strategies and various scalable and efficient devices for evaporation-based solar-driven desalination. This article will be helpful for the researchers in improving devices output and coming up with a sustainable desalination and water treatment.

Ten years of laser-induced graphene: impact and future prospect on biomedical, healthcare, and wearable technology

Since its introduction in 2014, laser-induced graphene (LIG) from commercial polymers has been gaining interests in both academic and industrial sectors. This can be clearly seen from its mass adoption in various fields ranging from energy storage and sensing platforms to biomedical applications. LIG is a 3-dimensional, nanoporous graphene structure with highly tuneable electrical, physical, and chemical properties. LIG can be easily produced by single-step laser scribing at normal room temperature and pressure using easily accessible commercial level laser machines and materials. With the increasing demand for novel wearable devices for biomedical applications, LIG on flexible substrates can readily serve as a technological platform to be further developed for biomedical applications such as point-of-care (POC) testing and wearable devices for healthcare monitoring system. This review will provide a comprehensive grounding on LIG from its inception and fabrication mechanism to the characterization of its key functional properties. The exploration of biomedicals applications in the form of wearable and point-of-care devices will then be presented. Issue of health risk from accidental exposure to LIG will be covered. Then LIG-based wearable devices will be compared to devices of different materials. Finally, we discuss the implementation of Internet of Medical Things (IoMT) to wearable devices and explore and speculate on its potentials and challenges.

An Overview of Diverse Strategies To Inactivate Enterobacteriaceae-Targeting Bacteriophages

Bacteriophages are viruses that infect bacteria and thus threaten industrial processes relying on the production executed by bacterial cells. Industries bear huge economic losses due to such recurring and resilient infections. Depending on the specificity of the process, there is a need for appropriate methods of bacteriophage inactivation, with an emphasis on being inexpensive and high efficiency. In this review, we summarize the reports on antiphagents, i.e., antibacteriophage agents on inactivation of bacteriophages. We focused on bacteriophages targeting the representatives of the Enterobacteriaceae family, as its representative, Escherichia coli, is most commonly used in the bio-industry. The review is divided into sections dealing with bacteriophage inactivation by physical factors, chemical factors, and nanotechnology-based solutions.

Reduced Graphene Oxide-Coated Fabrics for Joule-Heating and Antibacterial Applications

Multifunctional textiles have emerged as a significant area of research due to their growing importance and diverse applications. The main requirement for these fabrics is electroconductivity, which is usually gained by incorporating conductive materials such as graphene into the textile structure. In this article, an electrochemical method was demonstrated to integrate different loadings of reduced graphene oxide (rGO) into fabrics for enhanced electrical conductivity. The process involves spray coating of graphene oxide (GO) onto the fabric, followed by in situ electrochemical reduction of GO, resulting in a coating layer of rGO nanosheets. The rGO-coated fabric exhibited exceptional Joule-heating capabilities, achieving 127 °C under a 9 V direct voltage with only 770 μg/cm2 of rGO loading. Moreover, the antibacterial properties of the rGO-coated fabric were demonstrated, showing a significant reduction rate of over 99.99% against both Bacillus subtilis and Escherichia coli. Joule-heating and antibacterial performances of the rGO-coated fabric were investigated over eight repeated cycles, demonstrating excellent repeatability. The simplicity of the fabrication method, along with the electrothermal and antibacterial effects of the rGO-coated fabric, makes it a promising material for various practical applications.

Fabrication of Laser-Induced Graphene Based Flexible Sensors Using 355 nm Ultraviolet Laser and Their Application in Human-Computer Interaction System

In recent years, flexible sensors based on laser-induced graphene (LIG) have played an important role in areas such as smart healthcare, smart skin, and wearable devices. This paper presents the fabrication of flexible sensors based on LIG technology and their applications in human-computer interaction (HCI) systems. Firstly, LIG with a sheet resistance as low as 4.5 Ω per square was generated through direct laser interaction with commercial polyimide (PI) film. The flexible sensors were then fabricated through a one-step method using the as-prepared LIG. The applications of the flexible sensors were demonstrated by an HCI system, which was fabricated through the integration of the flexible sensors and a flexible glove. The as-prepared HCI system could detect the bending motions of different fingers and translate them into the movements of the mouse on the computer screen. At the end of the paper, a demonstration of the HCI system is presented in which words were typed on a computer screen through the bending motion of the fingers. The newly designed LIG-based flexible HCI system can be used by persons with limited mobility to control a virtual keyboard or mouse pointer, thus enhancing their accessibility and independence in the digital realm.

Wearable sensors for monitoring marine environments and their inhabitants

Human societies depend on marine ecosystems, but their degradation continues. Toward mitigating this decline, new and more effective ways to precisely measure the status and condition of marine environments are needed alongside existing rebuilding strategies. Here, we provide an overview of how sensors and wearable technology developed for humans could be adapted to improve marine monitoring. We describe barriers that have slowed the transition of this technology from land to sea, update on the developments in sensors to advance ocean observation and advocate for more widespread use of wearables on marine organisms in the wild and in aquaculture. We propose that large-scale use of wearables could facilitate the concept of an 'internet of marine life' that might contribute to a more robust and effective observation system for the oceans and commercial aquaculture operations. These observations may aid in rationalizing strategies toward conservation and restoration of marine communities and habitats.

In situ generation of highly localized chlorine by laser-induced graphene electrodes during electrochemical disinfection

Laser-induced graphene (LIG) has gained popularity for electrochemical water disinfection due to its efficient antimicrobial activity when activated with low voltages. However, the antimicrobial mechanism of LIG electrodes is not yet fully understood. This study demonstrated an array of mechanisms working synergistically to inactivate bacteria during electrochemical treatment using LIG electrodes, including the generation of oxidants, changes in pH-specifically high alkalinity associated with the cathode, and electro-adsorption on the electrodes. All these mechanisms may contribute to the disinfection process when bacteria are close to the surface of the electrodes where inactivation was independent of the reactive chlorine species (RCS); however, RCS was likely responsible for the predominant cause of antibacterial effects in the bulk solution (i.e., ≥100 mL in our study). Furthermore, the concentration and diffusion kinetics of RCS in solution was voltage-dependent. At 6 V, RCS achieved a high concentration in water, while at 3 V, RCS was highly localized on the LIG surface but not measurable in water. Despite this, the LIG electrodes activated by 3 V achieved a 5.5-log reduction in Escherichia coli (E.coli) after 120-min electrolysis without detectable chlorine, chlorate, or perchlorate in the water, suggesting a promising system for efficient, energy-saving, and safe electro-disinfection.

In-situ fabrication of titanium suboxide-laser induced graphene composites: Removal of organic pollutants and MS2 Bacteriophage

Titanium suboxides (TSO) are identified as a series of compounds showing excellent electro- and photochemical properties. TSO composites with carbon-based materials such as graphene have further improved water splitting and pollutant removal performance. However, their expensive and multi-step synthesis limits their wide-scale use. Furthermore, recently discovered laser-induced graphene (LIG) is a single-step and low-cost fabrication of graphene-based composites. Moreover, LIG's highly electrically conductive surface aids in tremendous environmental applications, including bacterial inactivation, anti-biofouling, and pollutant sensing. Here, we demonstrate the single-step in-situ fabrication of TSO-LIG composite by directly scribing the TiO₂ mixed poly(ether) sulfone sheets using a CO₂ infrared laser. In contrast, earlier composites were derived from either commercial-grade TSO or synthesized TSO with graphene. The characteristic Ti³⁺ peaks in XPS confirmed the conversion of TiO₂ into its sub-stoichiometric form, enhancing the electro-catalytical properties of the LIG-TiO_x composite surface. Electrochemical characterization, including impedance spectroscopy, validated the surface's enhanced electrochemical activity and electrode stability. Furthermore, the LIG-TiO_x composite surfaces were tested for anti-biofouling action and electrochemical application as electrodes and filters. The composite electrodes exhibit enhanced degradation performance for removing emerging pollutant antibiotics ciprofloxacin and methylene blue due to the in-situ hydroxyl radical generation. Additionally, the LIG-TiO_x conductive filters showed the complete 6-log killing of mixed bacterial culture and MS2 phage virus in flow-through filtration mode at 2.5 V, which is ∼2.5-log more killing compared to non-composited LIG filers at 500 Lm^-2h^-1. Nevertheless, these cost-effective LIG-TiO_x composites have excellent electrical properties and can be effectively utilized for energy and environmental applications.

Effect of Laser Parameters on Laser-Induced Graphene Filter Fabrication and Its Performance for Desalination and Water Purification

Laser-induced graphene (LIG) is a low-cost, chemical-free single-step fabrication process and has shown its potential in water treatment, electronics, and sensing. LIG fabrication optimization is mostly explored for dense polyimide (PI) polymers. However, LIG-based filters and membranes for water treatment need to be porous, and additional steps are required to get porous surfaces from PI-based surfaces. Polyethersulfone (PES) porous membranes are cost-effective and are common in water purification as compared to PI; further, the optimization of LIG fabrication on PES-based porous membranes is not explored. So, this study demonstrated the fabrication, optimization, and characterization of LIG with different laser parameters such as power, speed, image density (ID), focusing, laser platforms, and membrane support layer effect on porous PES commercial (UP010) and lab-casted 15% PES (PES15) membranes. The performance of optimized LIG filters was tested for interfacial evaporation (IE)-based desalination in single and stacked layer configuration and water purification applications such as dye removal and disinfection. IE was done in Joule heating (JH) and solar heating (SH) modes, and the UP010-ID7 LIG filter showed the highest JH evaporation rates of ∼1.1, 1.8, and 2.82 kg m^-2 h^-1 in single, double, and triple stacked configurations, respectively. Using a JH IE setup, the best-performing UP010-ID7 LIG filters have also shown ∼100% removal of methylene blue dye from the contaminated water. Furthermore, all LIG filters showed a complete 6-log bacterial inhibition at the 5 V filtration experiments; at 2.5 V, the optimized LIG filters showed a higher removal than the non-optimized filters. Additionally, the LIGs obtained with the aluminum platform were the best quality. This work demonstrates that laser power, ID, platform, and membrane support are critical parameters for the best-performing PES-LIG filters, and they can be effectively utilized to fabricate PES-based LIG porous surfaces for various energy, environmental, and catalysis applications.

Magnéli-Phase Ti4O7-Doped Laser-Induced Graphene Surfaces and Filters for Pollutant Degradation and Microorganism Removal

Laser-induced graphene (LIG) has recently become a point of attraction globally as an environmentally friendly method to fabricate graphene foam in a single step using a CO₂ laser. The electrical properties of LIG are studied in different environmental applications, such as bacterial inactivation, antibiofouling, and pollutant sensing. Furthermore, metal or nonmetal doping of graphene enhances its catalytical performance in pollutant degradation and decontamination. Magnéli phase (Ti_nO_2n-1) is a substoichiometric titanium oxide known for its high electrocatalytic behavior and chemical inertness and is being explored as a membrane or electrode material for environmental decontamination. Here, we show the fabrication and characterization of LIG-Magnéli-phase (Ti₄O₇) titanium suboxide composites as electrodes and filters on poly(ether sulfone). Unlike undoped LIG electrodes, the doped Ti₄O₇-LIG electrodes exhibit enhanced electrochemical activity, as demonstrated in electrochemical characterization using cyclic voltammetry and electrochemical impedance spectroscopy. Due to the in situ generation of hydroxyl radicals on the surface, the doped electrodes exhibit increase in methylene blue degradation and microorganism removal. Effects of voltage and doping were examined, resulting in a clear trend of degradation and decontamination performance proportional to the doping concentration and applied voltage giving the best result at 2.5 V for 10% Ti₄O₇ doping. The LIG-Ti₄O₇ surfaces also showed biofilm inhibition against mixed bacterial culture. The flow-through filtration using a LIG-Ti₄O₇ conductive filter showed complete bacterial killing with 6 log removal in the permeate at 2.5 V, an enhancement of ∼2.5 log compared to undoped LIG filters at a flow rate of ∼500 L m^-2 h^-1. The facile fabrication of Ti₄O₇-doped LIG with enhanced electrochemical properties can be effectively used for energy and environmental applications.

Magnéli phase titanium sub-oxides synthesis, fabrication and its application for environmental remediation: Current status and prospect

Sub-stoichiometric titanium oxide, also called titanium suboxides (TSO), had been a focus of research for many decades with a chemical composition of Ti_nO_2n-1 (n ≥ 1). It has a unique oxygen-deficient crystal structure which provides it an outstanding electrical conductivity and high corrosion resistance similar to ceramic materials. High electrical conductivity and ability to sustain in adverse media make these phases a point of attention for researchers in energy storage and environmental remediation applications. The Magnéli phase-based reactive electroconductive membranes (REM) and electrodes have demonstrated the electrochemical oxidation of pollutants in the water in flow-through and flow by configuration. Additionally, it has also shown its potential for visible light photochemical degradation as well. This review attempts to summarize state of the art in various Magnéli phases materials synthesis routes and their electrochemical and photochemical ability for environmental application. The manuscript introduces the Magnéli phase, its crystal structure, and catalytic properties, followed by the recent development in synthesis methods from diverse titanium sources, notably TiO₂ through thermal reduction. The various fabrication methods for Magnéli phase-base REMs and electrodes have also been summarized. Furthermore, the article discussed the environmental remediations via electrochemical and photochemical advanced oxidation processes. Additionally, the hybrid technology with REMs and electrodes is used to counter membrane biofouling and develop electrochemical sensing devices for the pollutants. The Magnéli phase materials have a bright future for both electrochemical and photochemical advanced oxidation of emerging contaminants in water and wastewater treatment.

Radio Frequency Heating of Washable Conductive Textiles for Bacteria and Virus Inactivation

The ongoing COVID-19 pandemic has increased the use of single-use medical fabrics such as surgical masks, respirators, and other personal protective equipment (PPE), which have faced worldwide supply chain shortages. Reusable PPE is desirable in light of such shortages; however, the use of reusable PPE is largely restricted by the difficulty of rapid sterilization. In this work, we demonstrate successful bacterial and viral inactivation through remote and rapid radio frequency (RF) heating of conductive textiles. The RF heating behavior of conductive polymer-coated fabrics was measured for several different fabrics and coating compositions. Next, to determine the robustness and repeatability of this heating response, we investigated the textile's RF heating response after multiple detergent washes. Finally, we show a rapid reduction of bacteria and virus by RF heating our conductive fabric. 99.9% of methicillin-resistant Staphylococcus aureus (MRSA) was removed from our conductive fabrics after only 10 min of RF heating; human cytomegalovirus (HCMV) was completely sterilized after 5 min of RF heating. These results demonstrate that RF heating conductive polymer-coated fabrics offer new opportunities for applications of conductive textiles in the medical and/or electronic fields.

Recent advances on inactivation of waterborne pathogenic microorganisms by (photo) electrochemical oxidation processes: Design and application strategies

Compared with other conventional water disinfection processes, (photo) electrochemical oxidation (P/ECO) processes have the characteristics of environmental friendliness, convenient installation and operation, easy control and high efficiency of inactivating waterborne pathogenic microorganisms (PMs), so that more and more research work has been focused on this topic, but there is still a huge gap between the research and practical application. Here, the research network of inactivating PMs by P/ECO processes has been comprehensively summarized, and the electrode/reactor/process design strategies based on strengthening direct and indirect oxidation, enhancing mass transfer efficiency and electron transfer efficiency, and improving the effective dose of electrogenerated oxidants are discussed. Furthermore, the factors affecting the inactivation of PMs and the issues regarding to stability and lifetime of the electrode are discussed respectively. Finally, the important research priorities and possible research challenges of P/ECO processes are put forward to make significant progress of this technology.

Laser-Induced Graphene (LIG) as a Smart and Sustainable Material to Restrain Pandemics and Endemics: A Perspective

A healthy environment is necessary for a human being to survive. The contagious COVID-19 virus has disastrously contaminated the environment, leading to direct or indirect transmission. Therefore, the environment demands adequate prevention and control strategies at the beginning of the viral spread. Laser-induced graphene (LIG) is a three-dimensional carbon-based nanomaterial fabricated in a single step on a wide variety of low-cost to high-quality carbonaceous materials without using any additional chemicals potentially used for antiviral, antibacterial, and sensing applications. LIG has extraordinary properties, including high surface area, electrical and thermal conductivity, environmental-friendliness, easy fabrication, and patterning, making it a sustainable material for controlling SARS-CoV-2 or similar pandemic transmission through different sources. LIG's antiviral, antibacterial, and antibiofouling properties were mainly due to the thermal and electrical properties and texture derived from nanofibers and micropores. This perspective will highlight the conducted research and the future possibilities on LIG for its antimicrobial, antiviral, antibiofouling, and sensing applications. It will also manifest the idea of incorporating this sustainable material into different technologies like air purifiers, antiviral surfaces, wearable sensors, water filters, sludge treatment, and biosensing. It will pave a roadmap to explore this single-step fabrication technique of graphene to deal with pandemics and endemics in the coming future.

Low-Voltage Bacterial and Viral Killing Using Laser-Induced Graphene-Coated Non-woven Air Filters

Laser-induced graphene (LIG) is uniquely positioned to advance applications in which electrically conductive carbon coatings are required. Recently, the antifouling, antiviral, and antibacterial properties of LIG have been proven in both air and water filtration applications. For example, an unsupported LIG based filter (pore size: ∼0.3 μm) demonstrated exceptional air filtration properties, while its joule heating effects successfully sterilized and removed unwanted biological components in air despite persisting challenges such as pressure drop, energy consumption, and lack of mechanical robustness. Here, we developed a polyimide (PI) non-woven supported LIG air filter with negligible pressure drop changes compared to the non-woven support material and showed that low electrical current density inactivates aerosolized bacteria. A current density of 4.5 mA/cm² did not cause significant joule heating, and 97.2% bacterial removal was obtained. The low-voltage antibacterial mechanism was elucidated using bacterial inhibition experiments on a titanium surface and on an LIG surface fabricated on dense PI films. Complete sterilization was obtained using current densities of ∼8 mA/cm² applied for 2 min or ∼ 6 mA/cm² for 10 min upon the dense PI-LIG surface. Lastly, >98% bacterial removal was observed using a low-resistance LIG-coated non-woven polyimide air filter at 5 V. However, only very low voltages (∼0.3 V) were needed to remove ∼99% Pseudomonas aeruginosa bacteria and 100% of T4 virus when the LIG-coated filters were hybridized with a stainless steel mesh. Our results show that low current density levels at very low voltages are sufficient for substantial bacterial and viral inactivation, and that these principles might be effectively used in a wide number of air filtration applications such as air conditioners or other ventilation systems, which might limit the spread of infectious particles in hospitals, homes, workplaces, and the transportation industry.