Preparation of Cellulose Nanoparticles from Foliage by Bio-Enzyme Methods

Efficient synthesis and investigation of waste-derived adsorbent for water purification. Exploring the impact of surface functionalization on methylene blue dye removal

In pursuit of sustainable water management, the preparation of adsorbent materials via waste upcycling for water purification practices plays a decisive role. The sulphonated biochar, PiNe-SO3H, employed to target the methylene blue dye adsorption, was successfully synthesized via a mild, step-economical chemical carbonization-functionalization reaction. The presence of SO3H groups on the PiNe-SO3H surface played a critical role in significantly enhancing the adsorption capacity. The observed MB dye uptake was predominantly attributed to chemisorption processes as evidenced by the results from kinetics, thermodynamics, and isotherms. To further confirm the role of -SO3H in the adsorption mechanism, a comparison was made with other PiNe materials lacking sulphonic groups, highlighting the superior adsorption capacity of PiNe-SO3H. Additionally, a fast and efficient regeneration process was proposed to develop a truly waste minimized protocol, enabling the recovery of up to 94 % of the ethanolic mixture used during this step.

Study on the effects of different pectinase/cellulase ratios and pretreatment times on the preparation of nanocellulose by ultrasound-assisted bio-enzyme heat treatment

With the development of science and technology, efficient, fast and green methods are increasingly being pursued. The production of nanocellulose by green methods, such as bio-enzymes-assisted ultrasound treatment, has been the focus of many studies. However, the yield of cellulose nanocrystals prepared by this method is very low. In this paper, by pretreatment of microcrystalline cellulose (MCC), nanocellulose was prepared by heating and stirring + pectinase/cellulase + ultrasonic treatment (HSt - P/C - Ultr). The effects of the ratios of pectinase and cellulase and the hydrolysis time on the yield of nanocellulose were studied. FTIR, XRD, SEM, TEM and TG were used to determine the structure, crystallinity, morphology and thermal stability of nanocellulose. The results showed that optimal hydrolysis conditions were determined as a pectinase : cellulase ratio of 1 : 1, 90 min and 50 °C. The yield of nanocellulose was about 32.0%. The yield of pectinase cellulase = 1 : 1 was higher than that of microcrystalline cellulose (MCC) treated by a single bio-enzyme. This indicated that the synergistic effects of pectinase and cellulase have a certain effect on the formation of nanocellulose. During the preparation, the crystalline form of cellulose did not change. It was still cellulose I with a crystallinity of 73.5%, which is 9.50% higher than that of microcrystalline cellulose (MCC), a width of 20-50 nm, a high aspect ratio and a winding network structure. Therefore, nanocellulose prepared by this method is an ideal toughening material for manufacturing composite materials.

Cellulosic pine needles-based biorefinery for a circular bioeconomy

Pine needles (PNs) are one of the largest bio-polymer produced worldwide. Its waste, i.e., fallen PNs, is mostly responsible for forest fires and is a major challenge. In present article, we have reviewed differenteffortsmadeto tackle this situation. PNs have been used in various fields such asin composite, water purification industries,electronic devices, etc. Gasification is one of the appealing processes for turning PNs into bio-energy; pyrolysis technique has been employed to create various carbon-based water purification materials; saccharification combined with fermentation produced good yields of bio-ethanol; Pd or Ni/PNs biocatalyst showed good catalytic properties in variousreactionsand pyrolysis with or without catalyst is an alluring technique to prepare bio-fuel. Nano cellulose extracted from PNs showed appealing thermal and mechanical strength. The air quality of nearbyenvironment was examinedby studying the magnetic properties of PNs. Packing materials made of PNs showed exceptional ethylene scavenging abilities.

Chemical and Enzymatic Fiber Modification to Enhance the Mechanical Properties of CMC Composite Films

Carboxymethyl cellulose (CMC) is a cellulose derivative that can be obtained from wood, bamboo, rattan, straw, and other cellulosic materials. CMC can be used to produce biofilms for many purposes, but the properties of these resulting films make them unsuitable for some applications. The effects of three kinds of plant fiber addition on CMC film properties was investigated using CMC derived from eucalyptus bark cellulose. Tensile strength (TS) and elongation at break (EB) of CMC/sodium alginate/glycerol composite films were 26.2 MPa and 7.35%, respectively. Tensile strength of CMC composite films substantially increased, reaching an optimum at 0.50 g of fiber. The enhancement due to industrial hemp hurd fiber on CMC composite films was more obvious. Pretreatment with hydrogen peroxide (H₂O₂) and glacial acetic acid (CH₃COOH) produced films with a TS of 35.9 MPa and an EB of 1.61%. TS values with pectinase pretreated fiber films was 41.3 MPa and EB was 1.76%. TS of films pretreated with pectinase and hemicellulase was 45.2 MPa and EB was 4.18%. Chemical and enzymatic treatment both improved fiber crystallinity, but film tensile strength was improved to a greater extent by enzymatic treatment. Surface roughness and pyrolysis residue of the film increased after fiber addition, but Fourier transform infrared spectroscopy (FTIR), opacity, and water vapor transmission coefficients were largely unchanged. Adding fiber improved tensile strength of CMC/sodium alginate/glycerol composite films and broadened the application range of CMC composite films without adversely affecting film performance.

Antibacterial Films Made of Bacterial Cellulose

Bacterial cellulose (BC) is naturally degradable, highly biocompatible, hydrophilic, and essentially non-toxic, making it potentially useful as a base for creating more sophisticated bio-based materials. BC is similar to plant-derived cellulose in terms of chemical composition and structure but has a number of important differences in microstructure that could provide some unique opportunities for use as a scaffold for other functions. In this study, bacterial cellulose was alkylated and then esterified to produce a carboxymethyl bacterial cellulose (CMBC) that was then used to produce six different composite films with potential antibacterial properties. The films were assessed for antibacterial activity against Staphylococcus aureus and Escherichia coli, pyrolysis characteristics using thermogravimetric analysis (TGA), microstructure using scanning electron microscopy (SEM), and mechanical properties. The addition of nano-silver (nano-Ag) markedly improved the antimicrobial activity of the films while also enhancing the physical and mechanical properties. The results indicate that the three-dimensional reticulated structure of the bacterial cellulose provides an excellent substrate for scaffolding other bioactive materials. Thus, the nano-BC was added into the CMBC/nano-Ag composites furthermore, and then the antibacterial and mechanical properties were improved 44% for E. coli, 59% for S. aureus, and 20% for tensile strength, respectively.

Effects of Raw Material Source on the Properties of CMC Composite Films

Sodium carboxymethyl cellulose (CMC) can be derived from a variety of cellulosic materials and is widely used in petroleum mining, construction, paper making, and packaging. CMCs can be derived from many sources with the final properties reflecting the characteristics of the original lignocellulosic matrix as well as the subsequent separation steps that affect the degree of carboxy methyl substitution on the cellulose hydroxyls. While a large percentage of CMCs is derived from wood pulp, many other plant sources may produce more attractive properties for specific applications. The effects of five plant sources on the resulting properties of CMC and CMC/sodium alginate/glycerol composite films were studied. The degree of substitution and resulting tensile strength in leaf-derived CMC was from 0.87 to 0.89 and from 15.81 to 16.35 MPa, respectively, while the degree of substitution and resulting tensile strength in wooden materials-derived CMC were from 1.08 to 1.17 and from 26.08 to 28.97 MPa, respectively. Thus, the degree of substitution and resulting tensile strength tended to be 20% lower in leaf-derived CMCs compared to those prepared from wood or bamboo. Microstructures of bamboo cellulose, bamboo CMC powder, and bamboo leaf CMC composites’ films all differed from pine-derived material, but plant source had no noticeable effect on the X-ray diffraction characteristics, Fourier transform infrared spectroscopy spectra, or pyrolysis properties of CMC or composites films. The results highlighted the potential for using plant source as a tool for varying CMC properties for specific applications.