Kinetics, Thermodynamics and Equilibrium Studies for Gold Recovery from Diluted Waste Solution

Ianăşi) P, Popa A, Lazău R, Negrea A, Negrea P, Duteanu N, Ciopec M, Nemes NS. Adsorbent Material Based on Carbon Black and Bismuth with Tunable Properties for Gold Recovery

Adsorption recovery of precious metals on a variety of solid substrates has steadily gained increased attention in recent years. Special attention was paid to the studies on the characterization of the adsorptive properties of materials with a high affinity for gold depending on the nature of the pendant groups present in the structure of the material. The aim of the present work was to synthesize and characterize a new material by using the sol-gel synthesis method (designated as BCb/CB). In this case, synthesis involved the following precursors: bismuth carbonate (III), carbon black, and IGEPAL surfactant (octylphenoxypolyethoxyethanol). Immobilization of the heterojunction as bismuth oxide over a flexible support such as carbon black (CB) can prevent their elution in solution and make it versatile for its use in a system. In this work, a new adsorbent material based on bismuth carbonate supported over carbon black (BCb/CB) was developed and used further for gold recovery from aqueous solutions. The required material was characterized physically/chemically by scanning electron microscopy (SEM); energy dispersive X-ray spectrometry (EDX); X-ray diffraction (XRD); thermal analysis (DTG/DTA); atomic force microscopy (AFM). The Brunauer-Emmett-Teller (BET) method was used to determine the specific surface area indicating a value of approximately 40 m²/g, higher than the surface of CB precursor (36 m²/g). The adsorptive properties and the adsorption mechanism of the materials were highlighted in order to recover Au(III). For this, static adsorption studies were carried out. The parameters that influence the adsorption process were studied, namely: the pH, the contact time, the temperature, and the initial concentration of the gold ions in the used solution. In order to establish the mechanism of the adsorption process, kinetic, thermodynamic, and equilibrium studies were carried out. Experimental data proved that the gold recovery can be conducted with maximum performance at pH 3, at room temperature. Thermodynamic studies proved that the gold adsorption on BCb/CB material is a spontaneous and endothermal process. The results indicate a total adsorption capacity of 13.1 mg Au(III)/g material. By using this material in real solutions, a recovery efficiency of 90.5% was obtained, concomitant with a higher selectivity (around 95%).

Selective Recovery of Gold from Electronic Waste by New Efficient Type of Sorbent

Modular connectors are applied by computer users, and they can be metallic secondary sources containing metals such as gold and copper. Because gold is a micro-component, the solution obtained after the pin digestion contains a low concentration of gold(III) ions, and efficient and selective sorbent should be used for gold(III) ion recovery. The selective removal of small amounts of gold(III) from 0.001-6 M hydrochloric acid solutions using pure and solvent-impregnated macroporous polystyrene crosslinked with divinylbenzene sorbents (Purolite MN 202 and Cyanex 272) is presented. Gold(III) ions were recovered effectively from the chloride solution after the digestion of the modular connector RJ 45 (8P8C) using Purolite MN 202 after the impregnation process. The dependence of the recovery percentage (R%) of gold(III) on the contact time was determined. The highest value of gold(III) ion sorption capacity (259.45 mg·g^-1) was obtained in 0.001 M HCl for Purolite MN202 after the Cyanex 272 impregnation. The results can be applied to gold recovery from e-waste. The presented method of gold recovery does not generate nitrogen oxides and does not require the use of cyanides.

Miniaturization of Anthracene-Containing Nonapeptides for Selective Precipitation/Recovery of Metallic Gold from Aqueous Solutions Containing Gold and Platinum Ions

The separation and recovery of noble metals is increasingly of interest, in particular the recovery of gold nanocrystals, which have applications in medicine and industry. Typically, metal recovery is performed using liquid–liquid extraction or electrowinning. However, it is necessary to develop noble metal recovery systems providing high selectivity in conjunction with a one-pot setup, ready product recovery, and the use of dilute aqueous solutions. In prior work, our group developed a selective gold recovery process using peptides. This previous research showed that RU065, a nonapeptide containing an anthracene moiety (at a concentration of 2.0 × 10−4 M), is capable of selective reduction of HAuCl4 to recover gold from a solution of HAuCl4 and H2PtCl6, each at 5.0 × 10−5 M. However, peptide molecules are generally costly to synthesize, and therefore it is important to determine the minimum required structural features to design non-peptide anthracene derivatives that could reduce operational costs. In this study, we used RU065 together with 23 of its fragment peptides and investigated the selective precipitation/recovery of metallic gold. RU0654–8, a fragment peptide comprising five amino acid residues (having two lysine, one L-isoleusine, and one L-alanine residue (representing six amide groups) along with an L-2-anthrylalanine residue) provided an Au/Pt atomic ratio of approximately 8, which was comparable to that for the full-length original RU065. The structural features identified in this study are expected to contribute to the design of non-peptide anthracene derivatives for low-cost, one-pot selective gold recovery.