Application of Bi12ZnO20 Sillenite as an Efficient Photocatalyst for Wastewater Treatment: Removal of Both Organic and Inorganic Compounds

Recent advances in designing and developing efficient sillenite-based materials for photocatalytic applications

Sillenite materials have been the subject of intense investigation for recent years due to their unique characteristics. They possess a distinct structure with space group I23, allowing them to exhibit distinctive features, such as an electronic structure ideal for certain applications such as photocatalysis. The present research delves into the structure, synthesis, and properties of sillenites, highlighting their suitability for photocatalysis. It explores also advanced engineering strategies for designing sillenite-based photocatalysts, including heterojunction formation, morphology modification, doping, and hybrid processes. Each strategy offers advantages and limitations that are critically discussed. The review then lists and discusses the photocatalytic performance of various sillenite-based systems recently developed for common applications, such as removing hazardous organic and inorganic contaminants, and even infrequent applications, such as microbial inactivation, H2 generation, CO2 reduction and N2 fixation. Finally, valuable insights and suggestions are put forward for future research directions in the field of sillenite-based photocatalysis. This comprehensive overview would provide a valuable resource for the development of efficient photocatalytic systems to address environmental and energy challenges.

Visible light-driven photocatalytic bacterial inactivation on PPE, supported by the DFT and bactericidal study

A novel ZnO-MoO₃-ZnMoO₃@graphene GZM composite catalyst prepared by microwave hydrothermal process for personal protective equipment textiles (PPE) is presented in this study. The results indicated that the GZM with defect vacancy sites of two types as observed by EPR showed significantly superior inactivation of the E. coli bacteria compared to GZM without the lower defect vacancy sites and concomitant lower electron densities. Photocatalytic activated oxidation by the GZM composites coatings was observed to proceed in acceptable times as well as the bacterial inactivation (log bact. C/C_o > 10⁷ within 3 h). Defect sites in the GZM seem to be important leading to the bacterial inactivation process. DFT calculations on the GZM with and without catalyst defect sites were carried out. The electron densities were estimated by the Fourier mapping. The results found in this study showed the potential of GZM-PPE for practical applications.

Selective Removal of Hexavalent Chromium by Novel Nitrogen and Sulfur Containing Cellulose Composite: Role of Counter Anions

Exploiting an adsorbent with superb selectivity is of utmost importance for the remediation of Cr (VI)-laden wastewater. In this work, a novel nitrogen and sulfur functionalized 3D macroporous cellulose material (MPS) was prepared by homogeneous cross-link cellulose and polyvinylimidazole, followed by ion exchange with MoS₄^2-. MPS exhibited high removal efficiency at a broad pH range (1.0-8.0) and large adsorption capacity (379.78 mg/g) toward Cr (VI). Particularly, outstanding selectivity with an enormous partition coefficient (1.01 × 10⁷ mL/g) was achieved on MPS. Replacing MoS₄^2- with Cl^- and MoO₄^2- led to a sharp decline in adsorption selectivity, demonstrating that MoS₄^2- contributed substantially to the selectivity. Results of FTIR, XPS, and apparent kinetic analysis revealed that Cr (VI) was first pre-enriched on the MPS surface via electrostatic and dispersion forces, and then reacted with MoS₄^2- to generate Cr (III), which deposited on MPS by forming Cr(OH)₃ and chromium(III) sulfide. This study provides a new idea for designing adsorbents with a superior selectivity for removing Cr (VI) from sewage.

Efficient removal of the antibiotic Cefixime on Mg0.3Zn0.7O under solar light: kinetic and mechanism studies

The heterogeneous photocatalysis is known to provide significant degradation and mineralization of emerging contaminants including antibiotics. For this, nanosized Mg_0.3Zn_0.7O (MZO) was prepared by nitrate route to be used as photocatalyst. The single-phase was confirmed by X-ray diffraction with a crystallite size of 33 nm. The morphology was visualized by scanning electron microscope/energy-dispersive X-ray analysis. The physicochemical properties were studied by the FTIR, XPS, and optical analyses. The diffuse reflectance gives a direct forbidden band of 3.26 eV. The electrochemical characterization showed an n-type semiconductor with a flat band of - 0.56 V_Ag/AgCl. The photodegradation of Cefixime (CFX) was carried out under solar light; the operating parameters such as the catalyst dose, solution pH, and initial CFX concentration (C_o) were optimized. The best performance occurs at neutral pH ~ 6 within 4 h with an abatement of 94% for an initial CFX concentration of 5 mg/L and MZO dose of 0.75 g/L. The photodegradation follows a first-order kinetic with an apparent rate constant of 0.012 min^-1. The effects of scavenging agents indicated the dominant role of hydroxyl ^•OH followed by the holes (h⁺). The results showed the potentiality of MZO as an environmentally friendly photocatalyst for CFX photodegradation.

The impact of material design on the photocatalytic removal efficiency and toxicity of two textile dyes

This study deals with the toxicity of the treated solutions of two types of dyes, namely, the anthraquinonic Reactive Bleu 19 dye (RB19) and the bi-azoic Direct Red 227 dye (DR227), which are treated in single and binary mixture systems. The target molecules were removed by the photocatalysis process using ZnO as a catalyst, which was calcined at two temperatures 250 and 420 °C (ZnO₂₅₀ and ZnO₄₂₀) prepared in the lab by the one-step calcination method. XRD, TEM, EDX, XPS, FT-IR, BET, RAMAN, and EPR analyses were carried out to characterize the catalyst material. While the phytotoxicity was being conducted using watercress seeds, the cytotoxicity took place using a cell line (raw) and an intestinal cell (caco-2). The XRD analysis showed the partial calcination of ZnO₂₅₀ and the presence of anhydrous zinc acetate along with the ZnO nanoparticles (NPs). This result was not observed for ZnO₄₂₀. Despite the complete discoloration (100%) of all the final solutions, ZnO₂₅₀ exhibited a high cytotoxicity and phytotoxicity against the RB19 dye after the photocatalytic treatment; however, it was not the case of ZnO₄₂₀ which was selected as an eco-friendly photocatalyst for the degradation of organic dyes based on the results of removal efficiency, cytotoxicity, and phytotoxicity.

Sorbent and Photocatalytic Potentials of Local Clays for the Removal of Organic Xenobiotic: Case of Crystal Violet

Natural materials are widely used in the field of environmental remediation and are appreciated for their surface physical and chemical properties. Clay constitutes a typical example. In this work, we report the evaluation of sorbent and photocatalytic potentials of local clay of two irrigated rice field waters in the degradation of crystal violet. The structural, textural and compositional properties of the local clay were investigated by Fourier Transform Infrared Spectroscopy (FTIR), X-ray Diffraction (XRD) and X-ray Fluorescence (XRF) analysis. The analysis results showed that these materials were composed mainly of quartz and kaolinite. The efficiency of these adsorbents (Y. Clay and L. Clay) to eliminate crystal violet dye from aqueous medium was examined at different initial concentrations, pH, contact time, adsorbent dose and the possible interference of inorganic salts from fertilizers. Kinetic studies showed that the adsorption process was well described by the pseudo-second order model and the equilibrium modelling results fitted adequately to the Freundlich model. The maximum amount of uptake capacity achieved at pH 2.0 was 18.40 (mg·g−1) and 20.40 (mg·g−1), respectively, for Y. Clay and L. Clay. The evaluation of the photocatalytic potential showed that the raw clay samples do not show photocatalytic activities during the 30 min of exposure to UV light. On the other hand, their photocatalytic potential is manifested when loaded with titanium dioxide (TiO2). Clays coupled with TiO2 under UV light showed an improvement in the degradation of the crystal violet dye by 15%. The synergistic effects between the high photocatalytic activity of TiO2 and the strong adsorption capacity of clays can be one promising technique for in situ remediation of contaminated soaked rice field.

Advanced Photocatalytic Treatment of Wastewater Using Immobilized Titanium Dioxide as a Photocatalyst in a Pilot-Scale Reactor: Process Intensification

In many nations, particularly those experiencing water scarcity, novel approaches are being applied to clean wastewater. Heterogeneous photocatalysis is the most widely used of these approaches because it entails the decomposition of organic molecules into water and carbon dioxide, which is a more ecologically benign process. In our study, we studied the photocatalytic degradation process on the effluent flumequine. This treatment is made through a solar pilot reactor in the presence of immobilized titanium dioxide with three light intensities and two types of water as solvents. A variety of factors that might influence the rate of deterioration, such as flow rate, light intensity, and initial concentration, have been investigated. The maximal degradation of flumequine was achieved at more than 90% after 2.5 h under optimal conditions (an initial concentration of 5 mg/L, three lamp light intensities, and a flow rate of 29 L/h). By combining the oxidized agent H2O2 with this process, the photocatalytic activity was improved further to 97% under the same conditions. The mineralization of this product has also been tested using total organic carbon (TOC) analysis. A high mineralization rate has been recorded at around 50% for a high initial concentration (20 mg/L) at a flow rate of 126 L/h. The results demonstrated the highly effective removal of flumequine and the efficacy of this photocatalytic system.

Bismuth Sillenite Crystals as Recent Photocatalysts for Water Treatment and Energy Generation: A Critical Review

Photocatalysis has been widely studied for environmental applications and water treatment as one of the advanced oxidation processes (AOPs). Among semiconductors that have been employed as catalysts in photocatalytic applications, bismuth sillenite crystals have gained a great deal of interest in recent years due to their exceptional characteristics, and to date, several sillenite material systems have been developed and their applications in photoactivity are under study. In this review paper, recent studies on the use of Bi-based sillenites for water treatment have been compiled and discussed. This review also describes the properties of Bi-based sillenite crystals and their advantages in the photocatalytic process. Various strategies used to improve photocatalytic performance are also reviewed and discussed, focusing on the specific advantages and challenges presented by sillenite-based photocatalysts. Furthermore, a critical point of certain bismuth catalysts in the literature that were found to be different from that reported and correspond to the sillenite form has also been reviewed. The effectiveness of some sillenites for environmental applications has been compared, and it has demonstrated that the activity of sillenites varies depending on the metal from which they were produced. Based on the reviewed literature, this review summarizes the current status of work with binary sillenite and provides useful insights for its future development, and it can be suggested that Bismuth sillenite crystals can be promising photocatalysts for water treatment, especially for degrading and reducing organic and inorganic contaminants. Our final review focus will emphasize the prospects and challenges of using those photocatalysts for environmental remediation and renewable energy applications.

Synthesis and Characterization of TiO2 Nanotubes (TiO2-NTs) with Ag Silver Nanoparticles (Ag-NPs): Photocatalytic Performance for Wastewater Treatment under Visible Light

In this work, we present the influence of the decoration of TiO₂ nanotubes (TiO₂-NTs) with Ag silver nanoparticles (Ag-NPs) on the photocatalysis of emerging pollutants such as the antibiotic diclofenac sodium. The Ag-NPs were loaded onto the TiO₂-NTs by the anodization of metallic titanium foils. Diclofenac sodium is an emerging pollutant target of the pharmaceutical industry because of its negative environmental impact (high toxicity and confirmed carcinogenicity). The obtained Ag-NP/TiO₂-NT nanocomposites were characterized by X-ray diffraction (XRD), photoluminescence spectroscopy (PL), scanning electron microscopy (SEM), transmission spectroscopy (TEM), and X-ray photoelectron spectroscopy (XPS). In order to study the photocatalytic behavior of Ag-NPs/TiO₂-NTs with visible cold LEDs, the possible photocatalytic mechanism of antibiotic degradation with reactive species (O₂°⁻ and OH°) was detailed. Moreover, the Langmuir–Hinshelwood model was used to correlate the experimental results with the optimized catalyst. Likewise, reuse tests showed the chemical stability of the catalyst.

A Review of the Use of Semiconductors as Catalysts in the Photocatalytic Inactivation of Microorganisms

Obtaining clean and high-quality water free of pathogenic microorganisms is a worldwide challenge. Various techniques have been investigated for achieving an effective removal or inactivation of these pathogenic microorganisms. One of those promising techniques is photocatalysis. In recent years, photocatalytic processes used semiconductors as photocatalysts. They were widely studied as a green and safe technology for water disinfection due to their high efficiency, being non-toxic and inexpensive, and their ability to disinfect a wide range of microorganisms under UV or visible light. In this review, we summarized the inactivation mechanisms of different waterborne pathogenic microorganisms by semiconductor photocatalysts. However, the photocatalytic efficiency of semiconductors photocatalysts, especially titanium dioxide, under visible light is limited and hence needs further improvements. Several strategies have been studied to improve their efficiencies which are briefly discussed in this review. With the developing of nanotechnology, doping with nanomaterials can increase and promote the semiconductor’s photocatalytic efficiency, which can enhance the deactivation or damage of a large number of waterborne pathogenic microorganisms. Here, we present an overview of antimicrobial effects for a wide range of nano-photocatalysts, including titanium dioxide-based, other metal-containing, and metal-free photocatalysts. Promising future directions and challenges for materials research in photocatalytic water disinfection are also concluded in this review.