Accuracy of the Intra- and Extra-Oral Scanning Technique for Transferring the Intaglio Surface of a Pontic of Provisional Restorations to Definitive Restorations

Influence of Repeated Cut-off and Rescanning on the Trueness of the Intraoral Digital Scans

OBJECTIVES

To evaluate the effects of repeated cut-off and rescan procedures on the trueness of three intraoral scanners (IOS).

METHODS

A tooth model (#16) with a standard class II cavity was prepared, and the complete-arch was scanned using a laboratory scanner (D2000, 3Shape A/S) to obtain a reference scan. Then the typodont was scanned with three IOSs (3Shape TRIOS 3, CEREC Omnicam, and Medit i500) under two rescanning strategies (full-cut and partial-cut), with varying numbers of repeated cut-off and rescanning procedures (0, 1, 3, 5, 7, or 10). The trueness discrepancy between the reference and experimental digital scan was estimated using root mean square (RMS) calculations. Three regions of interest were selected to represent the rescanning, identification, and non-rescan area. And the discrepancies were analyzed using a linear mixed model (α=.05).

RESULTS

Cut-off and rescanning procedures significantly decreased the trueness of digital scans in all test conditions compared to the reference. However, no progressive increase in discrepancy was observed under any rescan conditions. Significant influences on trueness were found based on the IOS used, with the 3Shape system exhibiting lower RMS values. The partial-cut strategy showed lower RMS values compared to the full-cut strategy, albeit without statistical significance.

CONCLUSIONS

While repeated cut-off and rescanning procedures led to a decline in the quality of digital impressions, they did not result in discrepancy accumulation with repeated rescanning.

CLINICAL SIGNIFICANCE

To ensure high scanning accuracy in dental practice, it is advisable to minimize the rescanning area when correcting imperfections in digital scans. Additionally, selecting an appropriate scanner can help mitigate the negative effects of the rescanning technique.

Soy-Based High-Protein Spheric Foods with the Appearance of Familiar Sugary Snacks

Excessive consumption of sugary foods increases the likelihood of obesity, as well as the preventable risk of lifestyle illnesses such as diabetes and cardiovascular diseases. Frequent intake of sweet snacks is considered to increase the risk of overweight/obesity in industrial nations. However, we cannot stop snacking against our better judgment. Therefore, in this study, we sought to develop high-protein, low-carb "mock snacks" to satisfy snack lovers' appetites and nutrition. Soy protein-based, ball-shaped food products with 57.7% (w/w) protein and 3.6% sugar have been developed. The addition of canola oil made them melty in the mouth without sacrificing their crispiness. Moreover, evaluation of the surface topography of the "soy balls" by 3D laser scanning demonstrated their high degree of sphericity. Conclusively, the snacks developed here may be one of the healthy alternatives for the current sugary ones.

Influence of intraoral conditions on the accuracy of digital and conventional implant impression techniques for two-implant-supported fixed dental prostheses

PURPOSE

To compare the trueness and precision of different impression techniques for two-implant-supported fixed dental prostheses between extraoral and intraoral conditions at different locations.

METHODS

Six volunteers participated in this study. A resin block with two parallel analogs was fabricated as an implant site simulator (ISS). The ISS was bonded to a molded ethylene vinyl acetate sheet to create a reference model. For each participant, four reference models were prepared based on the locations of the ISSs: maxillary posterior/anterior region (MaxP/MaxA) and mandibular posterior/anterior region (ManP/ManA). Five impressions were taken extraorally using the open-tray (conventional implant impression technique, CIT) and intraoral scanning (digital implant impression technique, DIT) techniques. The reference models were positioned in the participants' mouths, and impressions were obtained intraorally using the CIT and DIT. The interanalog distance (d) and angulation (θ) were measured to calculate trueness (Δd, Δθ) and precision (dP, θP). Two-way ANOVA and t tests were performed (α=0.05).

RESULTS

For the DIT, under intraoral conditions, the Δd and Δθ in MaxP and Δθ in ManP were significantly higher than those under extraoral conditions. For the CIT, under intraoral conditions, the Δd and Δθ in ManA and ManP and Δθ in MaxP were significantly lower than those under extraoral conditions. No significant differences in the dP and θP of either DIT or CIT were observed between the two conditions.

CONCLUSIONS

Intraoral conditions affected the trueness of DIT and CIT in different regions but had no influence on precision.

In Vivo Analysis of Intraoral Scanner Precision Using Open-Source 3D Software

Intraoral three-dimensional scanning techniques could be used to improve dental practice, leading to an improved overall quality of the prosthetic devices and improved comfort for the patient. An accurate and precise intraoral scanner allows proper diagnosis, follow-up evaluation, and prosthesis application. The aim of this research is to evaluate the precision of an intraoral scanners (Medit i500, Medit Corp., Seoul, Korea), using open-source software in the digital workflow. The precision was compared through repetitions of the scanning process of the upper dental arch, following superimpositions in the whole 3D arch area. It was possible to display colorimetric maps for qualitative comparison, and the deviations of the values were classified as clinically acceptable. Within the limitation of this study, the clinically acceptable in vivo frequency of points’ deviation, or the precision, was obtained in 98.8% ± 1.4%; therefore, the use of open-source software can be a viable option in the digital workflow, improving patient follow ups with the 3D model superimposition.