A Critical Appraisal of the Use and Properties of Nickel-Titanium Dental Alloys

Nanomechanical and bending properties of nickel-titanium orthodontics archwires by depth-sensing indentation

INTRODUCTION

This study aimed to identify the link between alloy microstructures and the nanomechanical properties of different orthodontic archwires containing nickel-titanium (NiTi) by sensing sliced areas. Previous studies have focused on analyzing and contrasting physical properties such as microhardness, elasticity modulus, and resistance; therefore, the trend is to consider microstructural characteristics in detail.

METHODS

Thirty archwire samples from 3 different commercial brands, American Orthodontics (AO), 3M Unitek (3M), and Borgatta, were analyzed through scanning electron microscopy and energy-dispersive x-ray spectroscopy, transmission electron microscopy, atomic force microscopy, Berkovich nanoindentation, and microtensile microscopy to determine their chemical-crystallographic characteristics and nanomechanical and bending characteristics.

RESULTS

The identified formulations of AO and 3M had averages of 20 wt%, for Ni and 15.4 wt% for Ti, with lower concentrations for Borgatta. Alloys of Ni and Ti were distributed in different concentrates in the matrix of the archwires. The nanomechanical properties showed high values of the elastic modulus (82.8 ± 3.6 GPa) and hardness (6.4 ± 1.2 GPa) and a minor deformation degree of 0.38% for the AO wires, although the bending strength exhibited the highest values for 3M. No corrosion was observed with a prolonged hydrolytic attack on the surface of any of the wires (0.0-0.5 National Bureau of Standards units).

CONCLUSIONS

The highest nanomechanical properties and bending characteristics were observed for wires with higher NiTi precipitate contents, which were distributed differently in the alloy overall in the matrix. The nanoindentations sensed in different areas evidenced different mechanical properties for NiTi depending on its concentrations of Ti and enucleations.

Assessment of Various Archwire Materials and Their Impact on Orthodontic Treatment Outcomes

Aim Orthodontic treatment relies heavily on the mechanical properties and surface characteristics of archwire materials to achieve optimal outcomes. This study aimed to comprehensively evaluate the mechanical properties, including tensile strength, yield strength, and modulus of elasticity, as well as the surface characteristics, such as surface roughness and frictional properties, of different archwire materials. Methods Four types of archwire materials, stainless steel, nickel-titanium (NiTi), beta-titanium, and esthetic archwires, were subjected to mechanical testing and surface analysis, with 31 in each group. Tensile testing was conducted to determine the maximum tensile strength, yield strength, and elastic modulus of each material. Surface roughness analysis was performed using profilometry techniques, and frictional properties were evaluated using an orthodontic friction testing apparatus. Results Stainless steel exhibited the highest tensile strength (900 N), followed by beta-titanium (850 N), NiTi (800 N), and esthetic archwire (750 N). Stainless steel also demonstrated the highest yield strength (780 N), followed by beta-titanium (740 N), NiTi (710 N), and esthetic archwire (650 N). The modulus of elasticity was the highest for stainless steel (200 GPa), followed by beta-titanium (170 GPa), NiTi (150 GPa), and esthetic archwires (120 GPa). Surface roughness was lowest in stainless steel archwires (mean Ra value of 0.25 µm), leading to reduced frictional resistance, whereas esthetic archwires exhibited the highest surface roughness (mean Ra value of 0.40 µm) and frictional forces. Significant differences in the mechanical properties and surface characteristics were observed among the materials (p < 0.05). Conclusions The choice of archwire material significantly influences orthodontic treatment outcomes by affecting the efficiency and effectiveness of tooth movement. Stainless steel and beta-titanium wires are ideal for high-stress applications, providing the robust mechanical strength necessary for complex movements. In contrast, NiTi wires, with their superelasticity, offer consistent and gentle forces, enhancing patient comfort and accelerating the alignment phase. Esthetic archwires, while visually appealing, often compromise mechanical performance, potentially prolonging treatment duration.

Effect of use of antiseptics and fluorides during orthodontic treatment on working properties of NiTi archwires in levelling dental arches : A randomized controlled trial

PURPOSE

The goal was to investigate whether the application of antiseptics and fluorides during orthodontic treatment affects the biomechanics of the levelling of dental arches by changing the working properties of nickel-titanium (NiTi) archwires.

METHODS

The sample consisted of 60 individuals aged 12-22 years (53% females). There were 20 individuals in each experimental group: (I) individuals conducted regular oral hygiene, (II) individuals used a high concentration of fluorides for intensive prophylaxis for the first month; and (III) individuals used chlorhexidine in the same manner. NiTi alloy archwires (dimensions 0.508 × 0.508 mm) were analyzed 3 months after intraoral exposure and compared to as-received NiTi wires. Elastic modulus, yield strength, springback ratio, and modulus of resilience were calculated. Dimensions of the dental arches were analyzed when NiTi alloy (T1) was placed intraorally and after 3 months (T2). Change was quantified as the difference in dimensions (T2-T1). Anterior width-to-length ratio was used as a measure for dental arch shape.

RESULTS

Intraoral exposure reduced elastic modulus, yield strength, springback ratio, modulus of resilience, loading, and unloading forces of NiTi wires (p ≤ 0.021). Chlorhexidine mouthwash and gel with high concentration of fluorides did not change these properties more than saliva with regular hygiene. The amount of change of dental arch shape in the maxilla and mandible did not differ significantly between the experimental groups.

CONCLUSION

Using antiseptics or a high concentration of fluorides during orthodontic treatment does not significantly affect the mechanical properties of NiTi wires and would not have clinical implications in changing orthodontic biomechanics.

Experimental Investigation of the Impact of Niobium Additions on the Structural Characteristics and Properties of Ti-5Cr-xNb Alloys for Biomedical Applications

In this study, a series of Ti-5Cr-xNb alloys with varying Nb content (ranging from 1 to 40 wt.%) were investigated to assess their suitability as implant materials. Comprehensive analyses were conducted, including phase analysis, microscopy examination, mechanical testing, and corrosion resistance evaluation. The results revealed significant structural alterations attributed to Nb addition, notably suppressing the formation of the ω phase and transitioning from α' + β + ω to single β phase structures. Moreover, the incorporation of Nb markedly improved the alloys' plastic deformation ability and reduced their elastic modulus. In particular, the Ti-5Cr-25Nb alloy demonstrated high values in corrosion potential and polarization resistance, signifying exceptional corrosion resistance. This alloy also displayed high bending strength (approximately 1500 MPa), a low elastic modulus (approximately 80 GPa), and outstanding elastic recovery and plastic deformation capabilities. These aggregate outcomes indicate the promising potential of the β-phase Ti-5Cr-25Nb alloy for applications in orthopedic and dental implants.

Microscopic and Mechanical Characterization of Co-Cr Dental Alloys Joined by the TIG Welding Process

Due to their good mechanical and other properties, cobalt-chromium alloys (Co-Cr) are often used in prosthetic therapy. The metal structures of prosthetic works can be damaged and break, and depending on the extent of the damage, they can be re-joined. Tungsten inert gas welding (TIG) produces a high-quality weld with a composition very close to that of the base material. Therefore, in this work, six commercially available Co-Cr dental alloys were joined by TIG welding, and their mechanical properties were evaluated to determine the quality of the TIG process as a technology for joining metallic dental materials and the suitability of the Co-Cr alloys used for TIG welding. Microscopic observations were made for this purpose. Microhardness was measured using the Vickers method. The flexural strength was determined on a mechanical testing machine. The dynamic tests were carried out on a universal testing machine. The mechanical properties were determined for welded and non-welded specimens, and the results were statistically evaluated. The results show the correlation between the investigated mechanical properties and the process TIG. Indeed, characteristics of the welds have an effect on the measured properties. Considering all the results obtained, the TIG-welded I-BOND NF and Wisil M alloys showed the cleanest and most uniform weld and, accordingly, satisfactory mechanical properties, highlighting that they withstood the maximum number of cycles under dynamic load.

Titanium and titanium alloys in dentistry: current trends, recent developments, and future prospects

Many implant materials have been used in various dental applications depending on their efficacy and availability. A dental implant must possess the required characteristics, such as biocompatibility, corrosion & wear resistance, adequate mechanical properties, osseointegration, etc., to ensure its safe and optimum use. This review analyzes various aspects of titanium (Ti) and Ti alloys, including properties, manufacturing processes, surface modifications, applications as dental implants, and limitations. In addition, it also presents a perception of recent advances in Ti-based implant materials and the futuristic development of innovative dental implants.

Study of Al–SiO2 Aesthetic Composite Coating on Orthodontic Metal Archwire

Nickel–titanium orthodontic wires (NTWs) play an essential role in orthodontic treatment. However, their corrosion and aesthetic properties limit their applications. To improve the aesthetic effects of nickel–titanium orthodontic archwires, we prepared aluminium–silicon dioxide (Al–SiO2) as a biocompatible layer coated onto the NTWs. The Al–SiO2 coating was first fabricated using physical vapor deposition magnetron sputtering, and its physicochemical and biocompatibility properties were investigated. Al–SiO2 layers were well coated on the NTWs. The corrosion currents in the nickel–titanium (NiTi) control, Al–SiO2-coated NiTi experimental, stainless steel (SS) control and Al–SiO2-coated SS experimental groups were 23.72 μA cm−2, 1.21 μA cm−2, 0.22 μA cm−2 and 0.06 μA cm−2, respectively. Al–SiO2-coated NTWs with reduced corrosion current density indicated that the preparation of Al–SiO2 coating on the surface of NiTi and SS could reduce the tendency of electrochemical corrosion. The friction coefficients of orthodontic wires in the NiTi control, NiTi experimental, SS control, and SS experimental groups were 0.68, 0.46, 0.58 and 0.45, respectively. A low friction coefficient was observed in the Al–SiO2-coated NTWs, and the reduced friction coefficient improved the efficiency of orthodontics. Furthermore, the excellent biocompatibility of the NTWs and SS coated with Al–SiO2 indicates that Al–SiO2 as a novel aesthetic layer could improve the physicochemical properties of NTW and SS without causing cytotoxicity, which has considerable potential for modification of NTW and SS surfaces.

The Effects of Temperature and Time of Heat Treatment on Thermo-Mechanical Properties of Custom-Made NiTi Orthodontic Closed Coil Springs

Nickel-Titanium (NiTi) springs have been increasingly used in orthodontics; however, no optimum condition of heat treatment has been reported. Therefore, this research was conducted to determine the optimum heat-treatment temperature and duration for the fabrication of NiTi-closed coil springs by investigating their effects on thermo-mechanical properties. As-drawn straight NiTi wires of 0.2 mm diameter were used to fabricate closed coil springs of 0.9 mm lumen diameter. The springs were heat-treated at three different temperatures (400, 450, and 500 °C) with three different durations (20, 40, and 60 min). Electron Probe Micro-Analysis (EPMA) and Differential Scanning Calorimetry (DSC) were used to investigate element composition and thermo-mechanical properties, respectively. Custom-made NiTi closed coil springs composed of 49.41%-Ti and 50.57%-Ni by atomic weight, where their DSC curves of 500 °C presented the obvious endothermic and exothermic peaks, and the austenite finish temperature (A_f) were approximately 25 °C. With increasing temperature, deactivation curves presented decreased plateau slopes generating higher superelastic ratios (SE ratios). At 500 °C, closed coil springs showed superelastic tendency with lower stress hysteresis. The thermo-mechanical properties were significantly influenced by heat-treatment temperature rather than duration. The optimum parameter appeared to be 500 °C for 40 min to produce appropriate force delivery levels, relatively low plateau slope, and lower hysteresis for orthodontic use.