Routes for Metallization of Perovskite Solar Cells

Impact of Temperature Optimization of ITO Thin Film on Tandem Solar Cell Efficiency

This study examined the impact of temperature optimization on indium tin oxide (ITO) films in monolithic HJT/perovskite tandem solar cells. ITO films were deposited using magnetron sputtering at temperatures ranging from room temperature (25 °C) to 250 °C. The sputtering target was ITO, with a mass ratio of In2O3 to SnO2 of 90% to 10%. The effects of temperature on the ITO film were analyzed using X-ray diffraction (XRD), spectroscopic ellipsometry, and sheet resistance measurements. Results showed that all ITO films exhibited a polycrystalline morphology, with diffraction peaks corresponding to planes (211), (222), (400), (440), and (622), indicating a cubic bixbyite crystal structure. The light transmittance exceeded 80%, and the sheet resistance was 75.1 Ω/sq for ITO deposited at 200 °C. The optical bandgap of deposited ITO films ranged between 3.90 eV and 3.93 eV. Structural and morphological characterization of the perovskite solar cell was performed using XRD and FE-SEM. Tandem solar cell performance was evaluated by analyzing current density-voltage characteristics under simulated sunlight. By optimizing the ITO deposition temperature, the tandem cell achieved a power conversion efficiency (PCE) of 16.74%, resulting in enhanced tandem cell efficiency.

Investigation of the Absorption Spectrum of InAs Doping Superlattice Solar Cells

InAs doping superlattice-based solar cells have great advantages in terms of the ability to generate clean energy in space or harsh environments. In this paper, multi-period InAs doping superlattice solar cells have been prepared.. Current density-voltage measurements were taken both in the dark and light, and the short-circuit current was estimated to be 19.06 mA/cm2. Efficiency improvements were achieved with a maximum one sun AM 1.5 G efficiency of 4.14%. Additionally, external quantum efficiency and photoluminescence with different temperature-dependent test results were taken experimentally. The corresponding absorption mechanisms were also investigated.

Recent Progress of Wide Bandgap Perovskites towards Two-Terminal Perovskite/Silicon Tandem Solar Cells

Perovskite/silicon tandem solar cells have garnered considerable interest due to their potential to surpass the Shockley-Queisser limit of single-junction Si solar cells. The rapidly advanced efficiencies of perovskite/silicon tandem solar cells benefit from the significant improvements in perovskite technology. Beginning with the evolution of wide bandgap perovskite cells towards two-terminal (2T) perovskite/silicon tandem solar cells, this work concentrates on component engineering, additives, and interface modification of wide bandgap perovskite cells. Furthermore, the advancements in 2T perovskite/silicon tandem solar cells are presented, and the influence of the central interconnect layer and the Si cell on the progression of the tandem solar cells is emphasized. Finally, we discuss the challenges and obstacles associated with 2T perovskite/silicon tandem solar cells, conducting a thorough analysis and providing a prospect for their future.

Kabatas MA, Jorio A, Zorkani I. Efficiency of InN/InGaN/GaN Intermediate-Band Solar Cell under the Effects of Hydrostatic Pressure, In-Compositions, Built-in-Electric Field, Confinement, and Thickness

This paper presents a thorough numerical investigation focused on optimizing the efficiency of quantum-well intermediate-band solar cells (QW-IBSCs) based on III-nitride materials. The optimization strategy encompasses manipulating confinement potential energy, controlling hydrostatic pressure, adjusting compositions, and varying thickness. The built-in electric fields in (In, Ga)N alloys and heavy-hole levels are considered to enhance the results' accuracy. The finite element method (FEM) and Python 3.8 are employed to numerically solve the Schrödinger equation within the effective mass theory framework. This study reveals that meticulous design can achieve a theoretical photovoltaic efficiency of quantum-well intermediate-band solar cells (QW-IBSCs) that surpasses the Shockley-Queisser limit. Moreover, reducing the thickness of the layers enhances the light-absorbing capacity and, therefore, contributes to efficiency improvement. Additionally, the shape of the confinement potential significantly influences the device's performance. This work is critical for society, as it represents a significant advancement in sustainable energy solutions, holding the promise of enhancing both the efficiency and accessibility of solar power generation. Consequently, this research stands at the forefront of innovation, offering a tangible and impactful contribution toward a greener and more sustainable energy future.

A Strategy for Tuning Electron-Phonon Coupling and Carrier Cooling in Lead Halide Perovskite Nanocrystals

Perovskites have been recognized as a class of promising materials for optoelectronic devices. We intentionally include excessive Cs+ cations in precursors in the synthesis of perovskite CsPbBr3 nanocrystals and investigate how the Cs+ cations influence the lattice strain in these perovskite nanocrystals. Upon light illumination, the lattice strain due to the addition of alkali metal Cs+ cations can be compensated by light-induced lattice expansion. When the Cs+ cation in precursors is about 10% excessive, the electron-phonon coupling strength can be reduced by about 70%, and the carrier cooling can be slowed down about 3.5 times in lead halide perovskite CsPbBr3 nanocrystals. This work reveals a new understanding of the role of Cs+ cations, which take the A-site in ABX3 perovskite and provide a new way to improve the performance of perovskites and their practical devices further.

Numerical Approach to the Plasmonic Enhancement of Cs2AgBiBr6 Perovskite-Based Solar Cell by Embedding Metallic Nanosphere

Lead-free Cs₂AgBiBr₆ perovskites have emerged as a promising, non-toxic, and eco-friendly photovoltaic material with high structural stability and a long lifetime of carrier recombination. However, the poor-light harvesting capability of lead-free Cs₂AgBiBr₆ perovskites due to the large indirect band gap is a critical factor restricting the improvement of its power conversion efficiency, and little information is available about it. Therefore, this study focused on the plasmonic approach, embedded metallic nanospheres in Cs₂AgBiBr₆ perovskite solar cells, and quantitatively investigated their light-harvesting capability via finite-difference time-domain method. Gold and palladium were selected as metallic nanospheres and embedded in a 600 nm thick-Cs₂AgBiBr₆ perovskite layer-based solar cell. Performances, including short-circuit current density, were calculated by tuning the radius of metallic nanospheres. Compared to the reference devices with a short-circuit current density of 14.23 mA/cm², when a gold metallic nanosphere with a radius of 140 nm was embedded, the maximum current density was improved by about 1.6 times to 22.8 mA/cm². On the other hand, when a palladium metallic nanosphere with the same radius was embedded, the maximum current density was improved by about 1.8 times to 25.8 mA/cm².

Recent Progress in Perovskite Tandem Solar Cells

Tandem solar cells are widely considered the industry's next step in photovoltaics because of their excellent power conversion efficiency. Since halide perovskite absorber material was developed, it has been feasible to develop tandem solar cells that are more efficient. The European Solar Test Installation has verified a 32.5% efficiency for perovskite/silicon tandem solar cells. There has been an increase in the perovskite/Si tandem devices' power conversion efficiency, but it is still not as high as it might be. Their instability and difficulties in large-area realization are significant challenges in commercialization. In the first part of this overview, we set the stage by discussing the background of tandem solar cells and their development over time. Subsequently, a concise summary of recent advancements in perovskite tandem solar cells utilizing various device topologies is presented. In addition, we explore the many possible configurations of tandem module technology: the present work addresses the characteristics and efficacy of 2T monolithic and mechanically stacked four-terminal devices. Next, we explore ways to boost perovskite tandem solar cells' power conversion efficiencies. Recent advancements in the efficiency of tandem cells are described, along with the limitations that are still restricting their efficiency. Stability is also a significant hurdle in commercializing such devices, so we proposed eliminating ion migration as a cornerstone strategy for solving intrinsic instability problems.

Influence of Halides on Elastic and Vibrational Properties of Mixed-Halide Perovskite Systems Studied by Brillouin and Raman Scattering

The relationship between halogen content and the elastic/vibrational properties of MAPbBr_3-xCl_x mixed crystals (x = 1.5, 2, 2.5, and 3) with MA = CH₃NH₃⁺ has been studied using Brillouin and Raman spectroscopy at room temperature. The longitudinal and transverse sound velocities, the absorption coefficients and the two elastic constants C₁₁ and C₄₄ could be obtained and compared for the four mixed-halide perovskites. In particular, the elastic constants of the mixed crystals have been determined for the first time. A quasi-linear increase in the sound velocity and the elastic constant C₁₁ with increasing chlorine content was observed for the longitudinal acoustic waves. C₄₄ was insensitive to the Cl content and very low, indicating a low elasticity to shear stress in mixed perovskites regardless of the Cl content. The acoustic absorption of the LA mode increased with increasing heterogeneity in the mixed system, especially for the intermediate composition where the Br and Cl ratio was 1:1. In addition, a significant decrease in the Raman-mode frequency of the low-frequency lattice modes and the rotational and torsional modes of the MA cations was observed with decreasing Cl content. It clearly showed that the changes in the elastic properties as the halide composition changes were correlated with the lattice vibrations. The present findings may facilitate a deeper understanding of the complex interplay between halogen substitution, vibrational spectra and elastic properties, and may also pave the way for optimizing the operation of perovskite-based photovoltaic and optoelectronic devices by tailoring their chemical composition.

Anharmonicity of Plasmons in Metallic Nanostructures Useful for Metallization of Solar Cells

Metallic nanoparticles are frequently applied to enhance the efficiency of photovoltaic cells via the plasmonic effect, and they play this role due to the unusual ability of plasmons to transmit energy. The absorption and emission of plasmons, dual in the sense of quantum transitions, in metallic nanoparticles are especially high at the nanoscale of metal confinement, so these particles are almost perfect transmitters of incident photon energy. We show that these unusual properties of plasmons at the nanoscale are linked to the extreme deviation of plasmon oscillations from the conventional harmonic oscillations. In particular, the large damping of plasmons does not terminate their oscillations, even if, for a harmonic oscillator, they result in an overdamped regime.

Device Simulation of Highly Stable and 29% Efficient FA0.75MA0.25Sn0.95Ge0.05I3-Based Perovskite Solar Cell

A new type of perovskite solar cell based on mixed tin and germanium has the potential to achieve good power conversion efficiency and extreme air stability. However, improving its efficiency is crucial for practical application in solar cells. This paper presents a quantitative analysis of lead-free FA_0.75MA_0.25Sn_0.95Ge_0.05I₃ using a solar cell capacitance simulator to optimize its structure. Various electron transport layer materials were thoroughly investigated to enhance efficiency. The study considered the impact of energy level alignment between the absorber and electron transport layer interface, thickness and doping concentration of the electron transport layer, thickness and defect density of the absorber, and the rear metal work function. The optimized structures included poly (3,4-ethylenedioxythiophene)polystyrene sulfonate (PEDOT:PSS) as the hole transport layer and either zinc oxide (ZnO) or zinc magnesium oxide (Zn_0.7Mg_0.3O) as the electron transport layer. The power conversion efficiency obtained was 29%, which was over three times higher than the initial structure. Performing numerical simulations on FA_0.75MA_0.25Sn_0.95Ge_0.05I₃ can significantly enhance the likelihood of its commercialization. The optimized values resulting from the conducted parametric study are as follows: a short-circuit current density of 30.13 mA·cm^-2), an open-circuit voltage of 1.08 V, a fill factor of 86.56%, and a power conversion efficiency of 28.31% for the intended solar cell.

Efficient Charge Transfer in MAPbI3 QDs/TiO2 Heterojunctions for High-Performance Solar Cells

Methylammonium lead iodide (MAPbI₃) perovskite quantum dots (QDs) have become one of the most promising materials for optoelectronics. Understanding the dynamics of the charge transfer from MAPbI₃ QDs to the charge transport layer (CTL) is critical for improving the performance of MAPbI₃ QD photoelectronic devices. However, there is currently less consensus on this. In this study, we used an ultrafast transient absorption (TA) technique to investigate the dynamics of charge transfer from MAPbI₃ QDs to CTL titanium dioxide (TiO₂), elucidating the dependence of these kinetics on QD size with an injection rate from 1.6 × 10¹⁰ to 4.3 × 10¹⁰ s^-1. A QD solar cell based on MAPbI₃/TiO₂ junctions with a high-power conversion efficiency (PCE) of 11.03% was fabricated, indicating its great potential for application in high-performance solar cells.

Research Progress of Green Solvent in CsPbBr3 Perovskite Solar Cells

In optoelectronic applications, all-Brominated inorganic perovskite CsPbBr₃ solar cells have received a great deal of attention because of their remarkable stability and simplicity of production. Most of the solvents used in CsPbBr₃ perovskite solar cells are toxic, which primarily hinders the commercialization of the products. In this review, we introduce the crystal structure and fundamental properties of CsPbBr₃ materials and the device structure of perovskite cells, summarize the research progress of green solvents for CsPbBr₃ PSCs in recent years from mono-green solvent systems to all-green solvent systems, and discuss the approaches to improving the PCE of CsPbBr₃ PSCs, intending to facilitate the sustainable development of CsPbBr₃ perovskite solar cells. Finally, we survey the future of green solvents in the area of CsPbBr₃ perovskite solar cells.

Lead-Free Perovskite Homojunction-Based HTM-Free Perovskite Solar Cells: Theoretical and Experimental Viewpoints

Simplifying the design of lead-free perovskite solar cells (PSCs) has drawn a lot of interest due to their low manufacturing cost and relative non-toxic nature. Focus has been placed mostly on reducing the toxic lead element and eliminating the requirement for expensive hole transport materials (HTMs). However, in terms of power conversion efficiency (PCE), the PSCs using all charge transport materials surpass the environmentally beneficial HTM-free PSCs. The low PCEs of the lead-free HTM-free PSCs could be linked to poorer hole transport and extraction as well as lower light harvesting. In this context, a lead-free perovskite homojunction-based HTM-free PSC was investigated, and the performance was then assessed using a Solar Cell Capacitance Simulator (SCAPS). A two-step method was employed to fabricate lead-free perovskite homojunction-based HTM-free PSCs in order to validate the simulation results. The simulation results show that high hole mobility and a narrow band gap of cesium tin iodide (CsSnI₃) boosted the hole collection and absorption spectrum, respectively. Additionally, the homojunction's built-in electric field, which was identified using SCAPS simulations, promoted the directed transport of the photo-induced charges, lowering carrier recombination losses. Homojunction-based HTM-free PSCs having a CsSnI₃ layer with a thickness of 100 nm, defect density of 10¹⁵ cm^-3, and interface defect density of 10¹⁸ cm^-3 were found to be capable of delivering high PCEs under a working temperature of 300 K. When compared to formamidinium tin iodide (FASnI₃)-based devices, the open-circuit voltage (V_oc), short-circuit density (J_sc), fill factor (FF), and PCE of FASnI₃/CsSnI₃ homojunction-based HTM-free PSCs were all improved from 0.66 to 0.78 V, 26.07 to 27.65 mA cm^-2, 76.37 to 79.74%, and 14.62 to 19.03%, respectively. In comparison to a FASnI₃-based device (PCE = 8.94%), an experimentally fabricated device using homojunction of FASnI₃/CsSnI₃ performs better with V_oc of 0.84 V, J_sc of 22.06 mA cm^-2, FF of 63.50%, and PCE of 11.77%. Moreover, FASnI₃/CsSnI₃-based PSC is more stable over time than its FASnI₃-based counterpart, preserving 89% of its initial PCE. These findings provide promising guidelines for developing highly efficient and environmentally friendly HTM-free PSCs based on perovskite homojunction.

Full Optoelectronic Simulation of Lead-Free Perovskite/Organic Tandem Solar Cells

Organic and perovskite semiconductor materials are considered an interesting combination thanks to their similar processing technologies and band gap tunability. Here, we present the design and analysis of perovskite/organic tandem solar cells (TSCs) by using a full optoelectronic simulator (SETFOS). A wide band gap lead-free ASnI₂Br perovskite top subcell is utilized in conjunction with a narrow band gap DPPEZnP-TBO:PC61BM heterojunction organic bottom subcell to form the tandem configuration. The top and bottom cells were designed according to previous experimental work keeping the same materials and physical parameters. The calibration of the two cells regarding simulation and experimental data shows very good agreement, implying the validation of the simulation process. Accordingly, the two cells are combined to develop a 2T tandem cell. Further, upon optimizing the thickness of the front and rear subcells, a current matching condition is satisfied for which the proposed perovskite/organic TSC achieves an efficiency of 13.32%, J_sc of 13.74 mA/cm², and V_oc of 1.486 V. On the other hand, when optimizing the tandem by utilizing full optoelectronic simulation, the tandem shows a higher efficiency of about 14%, although it achieves a decreased J_sc of 12.27 mA/cm². The study shows that the efficiency can be further improved when concurrently optimizing the various tandem layers by global optimization routines. Furthermore, the impact of defects is demonstrated to highlight other possible routes to improve efficiency. The current simulation study can provide a physical understanding and potential directions for further efficiency improvement for lead-free perovskite/organic TSC.

Monovalent Copper Cation Doping Enables High-Performance CsPbIBr2-Based All-Inorganic Perovskite Solar Cells

Organic-inorganic perovskite solar cells (PSCs) have delivered the highest power conversion efficiency (PCE) of 25.7% currently, but they are unfortunately limited by several key issues, such as inferior humid and thermal stability, significantly retarding their widespread application. To tackle the instability issue, all-inorganic PSCs have attracted increasing interest due to superior structural, humid and high-temperature stability to their organic-inorganic counterparts. Nevertheless, all-inorganic PSCs with typical CsPbIBr₂ perovskite as light absorbers suffer from much inferior PCEs to those of organic-inorganic PSCs. Functional doping is regarded as a simple and useful strategy to improve the PCEs of CsPbIBr₂-based all-inorganic PSCs. Herein, we report a monovalent copper cation (Cu⁺)-doping strategy to boost the performance of CsPbIBr₂-based PSCs by increasing the grain sizes and improving the CsPbIBr₂ film quality, reducing the defect density, inhibiting the carrier recombination and constructing proper energy level alignment. Consequently, the device with optimized Cu⁺-doping concentration generates a much better PCE of 9.11% than the pristine cell (7.24%). Moreover, the Cu⁺ doping also remarkably enhances the humid and thermal durability of CsPbIBr₂-based PSCs with suppressed hysteresis. The current study provides a simple and useful strategy to enhance the PCE and the durability of CsPbIBr₂-based PSCs, which can promote the practical application of perovskite photovoltaics.

Improved Power Conversion Efficiency with Tunable Electronic Structures of the Cation-Engineered [Ai]PbI3 Perovskites for Solar Cells: First-Principles Calculations

Higher power conversion efficiencies for photovoltaic devices can be achieved through simple and low production cost processing of APbI3(A=CH3NH3,CHN2H4,…) perovskites. Due to their limited long-term stability, however, there is an urgent need to find alternative structural combinations for this family of materials. In this study, we propose to investigate the prospects of cation-substitution within the A-site of the APbI3 perovskite by selecting nine substituting organic and inorganic cations to enhance the stability of the material. The tolerance and the octahedral factors are calculated and reported as two of the most critical geometrical features, in order to assess which perovskite compounds can be experimentally designed. Our results showed an improvement in the thermal stability of the organic cation substitutions in contrast to the inorganic cations, with an increase in the power conversion efficiency of the Hydroxyl-ammonium (NH3OH) substitute to η = 25.84%.

Nanostructured AlGaAsSb Materials for Thermophotovoltaic Solar Cells Applications

Thermophotovoltaic conversion using heat to generate electricity in photovoltaic cells based on the detraction of thermal radiation suffers from many engineering challenges. The focus of this paper is to study the nanostructure of AlGaAsSb for thermophotovoltaic energy conversion using lattice-matched heterostructures of GaSb-based materials in order to overcome the current challenges. The XAFS spectroscopy technique was used to analyze electronic structures and optical properties of GaSb, (Al, In) GaSbAs. The XAFS spectroscopy analysis showed a powerful decay at peak intensity that reveals to be related to a loss in Sb amount and light As atoms replaced in Sb atoms by 25%. Moreover, it was found that Al/In doped samples have highly symmetric data features (same atomic species substitution). The narrow direct bandgap energy, E_g of Al_0.125Ga_0.875Sb_0.75As_0.25 material raised (0.4-0.6 eV) compared to conventional photovoltaic cell bandgap energy (which is generally less than 0.4 eV) with weak absorption coefficients. The thermoelectric properties of AlGaAsSb computed via Botlztrap code showed that the electrons made up the majority of the charge carriers in AlGaAsSb. This nanostructure material exhibited a higher and acceptable figure of merit and demonstrated a promising thermoelectric material for solar thermophotovoltaic applications.

Electronic Structures and Photoelectric Properties in Cs3Sb2X9 (X = Cl, Br, or I) under High Pressure: A First Principles Study

Lead-free perovskites of Cs₃Sb₂X₉ (X = Cl, Br, or I) have attracted wide attention owing to their low toxicity. High pressure is an effective and reversible method to tune bandgap without changing the chemical composition. Here, the structural and photoelectric properties of Cs₃Sb₂X₉ under high pressure were theoretically studied by using the density functional theory. The results showed that the ideal bandgap for Cs₃Sb₂X₉ can be achieved by applying high pressure. Moreover, it was found that the change of the bandgap is caused by the shrinkage of the Sb-X long bond in the [Sb₂X₉]^3- polyhedra. Partial density of states indicated that Sb-5s and X-p orbitals contribute to the top of the valence band, while Sb-5p and X-p orbitals dominate the bottom of the conduction band. Moreover, the band structure and density of states showed significant metallicity at 38.75, 24.05 GPa for Cs₃Sb₂Br₉ and Cs₃Sb₂I₉, respectively. Moreover, the absorption spectra showed the absorption edge redshifted, and the absorption coefficient of the Cs₃Sb₂X₉ increased under high pressure. According to our calculated results, the narrow bandgap and enhanced absorption ability under high pressure provide a new idea for the design of the photovoltaic and photoelectric devices.

Effects of Different Anti-Solvents and Annealing Temperatures on Perovskite Thin Films

Since perovskite materials are currently mostly used in the active layer of solar cells, how to maximize the conversion efficiency of the active layer is the most urgent problem at present. In this regard, the extremely low voltage loss and tunable energy gap of methyl lead iodide (MAPbI3) perovskites make them very suitable for all perovskite solar cell applications, and are also compatible with silicon crystalline systems. Therefore, the future development of MAPbI3 perovskite will be very important. The key point of film formation in MAPbI3 is the addition of anti-solvent, which will affect the overall quality of the film. Whether it can be used as an excellent active layer to improve the application value will be very important. Therefore, the research purpose of this topic “Effects of different anti-solvents and annealing temperatures on perovskites” is to complete the basic research and development of a light-absorbing layer of a solar cell element, in which three different anti-solvents need to be matched with each other as the active light-absorbing layer of a solar cell. Through optimization, using the chemical properties of different anti-solvents and different annealing temperatures, combined with the low-process-cost characteristics of organic materials and many other advantages, we researched the optimized process methods and parameters to improve the absorption efficiency of the active light-absorbing layer.

Temperature Dependence of Photochemical Degradation of MAPbBr3 Perovskite

The experimental results of X-ray diffraction (XRD), optical absorbance, scanning electron microscopy (SEM), and X-ray photoelectron spectra (XPS) of the core levels and valence bands of MAPbBr3 (MA-CH3NH3+) perovskite before and after exposure to visible light for 700 h at temperatures of 10 and 60 °C are presented. It reveals that the light soaking at 60 °C induces the decomposition of MAPbBr3 perovskite accompanied with the decay of organic cation and the release of a PbBr2 phase as a degradation product whereas the photochemical degradation completely disappears while the aging temperature is decreased to 10 °C.

Optoelectronic Enhancement of Perovskite Solar Cells through the Incorporation of Plasmonic Particles

The optoelectronic advantages of anchoring plasmonic silver and copper particles and non-plasmonic titanium particles onto zinc oxide (ZnO) nanoflower (NF) scaffolds for the fabrication of perovskite solar cells (PSCs) are addressed in this article. The metallic particles were sputter-deposited as a function of sputtering time to vary their size on solution-grown ZnO NFs on which methylammonium lead iodide perovskite was crystallized in a controlled environment. Optical absorption measurements showed impressive improvements in the light-harvesting efficiency (LHE) of the devices using silver nanoparticles and some concentrations of copper, whereas the LHE was relatively lower in devices used titanium than in a control device without any metallic particles. Fully functional PSCs were fabricated using the plasmonic and non-plasmonic metallic film-decorated ZnO NFs. Several fold enhancements in photoconversion efficiency were achieved in the silver-containing devices compared with the control device, which was accompanied by an increase in the photocurrent density, photovoltage, and fill factor. To understand the plasmonic effects in the photoanode, the LHE, photo-current density, photovoltage, photoluminescence, incident photon-to-current conversion efficiency, and electrochemical impedance properties were thoroughly investigated. This research showcases the efficacy of the addition of plasmonic particles onto photo anodes, which leads to improved light scattering, better charge separation, and reduced electron–hole recombination rate.

All-Inorganic Perovskite Single Crystals for Optoelectronic Detection

Due to their many varieties of excellent optoelectric properties, perovskites have attracted large numbers of researchers in the past few years. For the hybrid perovskites, a long diffusion length, long carrier lifetime, and high μτ product are particularly noticeable. However, some disadvantages, including high toxicity and instability, restrict their further large-scale application. By contrast, all-inorganic perovskites not only have remarkable optoelectric properties but also feature high structure stability due to the lack of organic compositions. Benefiting from these, all-inorganic perovskites have been extensively explored and studied. Compared with the thin film type, all-inorganic perovskite single crystals (PSCs) with fewer grain boundaries and crystalline defects have better optoelectric properties. Nevertheless, it is important to note that only a few reports to date have presented a summary of all-inorganic PSCs. In this review, we firstly make a summary and propose a classification method according to the crystal structure. Then, based on the structure classification, we introduce several representative materials and focus on their corresponding growth methods. Finally, applications for detectors of all-inorganic PSCs are listed and summarized. At the end of the review, based on the current research situation and trends, some perspectives and advice are proposed.