Metabolically Doping of 3D Diatomaceous Biosilica with Titanium

Diatom Biosilica Functionalised with Metabolically Deposited Cerium Oxide Nanoparticles

This study introduces a novel approach to synthesising a three-dimensional (3D) micro-nanostructured amorphous biosilica. The biosilica is coated with cerium oxide nanoparticles obtained from laboratory-grown unicellular photosynthetic algae (diatoms) doped metabolically with cerium. This unique method utilises the ability of diatom cells to absorb cerium metabolically and deposit it on their silica exoskeleton as cerium oxide nanoparticles. The resulting composite (Ce-DBioSiO2) combines the unique structural and photonic properties of diatom biosilica (DBioSiO2) with the functionality of immobilised CeO2 nanoparticles. The kinetics of the cerium metabolic insertion by diatom cells and the physicochemical properties of the obtained composites were thoroughly investigated. The resulting Ce-DBioSiO2 composite exhibits intense Stokes fluorescence in the violet-blue region under ultraviolet (UV) irradiation and anti-Stokes intense violet and faint green emissions under the 800 nm near-infrared excitation with a xenon lamp at room temperature in an ambient atmosphere.

Hydraulic retention time governed the micro/nanostructures of titanium-incorporated diatoms and their photocatalytic activity

Titanium-incorporated diatoms are promising biomaterials to photodegrade micropollutants such as pharmaceuticals and personal care products (PPCPs). Hydraulic retention time (HRT) is a key parameter for diatom cultivation and the incorporation of titanium into diatom frustules. This study assessed how HRT governs the micro/nanostructures, titania (TiO2) content and distribution, and the photocatalytic activity of titanium-incorporated diatom frustules. We cultivated a diatom strain Stephanodiscus hantzschii using a feed solution containing titanium(IV) in membrane bioreactors (MBRs) at a solids retention time (SRT) of 10 d and staged HRTs from 24 to 12 and to 6 h. The decrease in HRT reduced the porosity of diatom frustules but increased their silicon and titania contents. When the HRT decreased from 24 to 12 and to 6 h, the specific surface areas of the diatom decreased from 37.65 ± 3.19 to 31.53 ± 3.71 and to 18.43 ± 2.69 m2·g-1 frustules, while the titanium (Ti) contents increased from 53 ± 14 to 71 ± 9 and to 85 ± 13 mg Ti·g-1 frustules. The increase in the influent flow rates of the MBRs with decreasing HRTs likely enhanced nutrient diffusion inside the diatom valve pores, facilitating the uptake and incorporation of silicon and titanium. The titanium-incorporated frustules were effective in removing two representative PPCPs, bisphenol A (BPA) and N,N-diethyl-meta-toluamide (DEET), from water. As photocatalytic activity depends on the amount of titanium, decreasing the HRT substantially increased the photocatalytic activity of the titanium-incorporated frustules. In batch tests under ultraviolet light, frustules from the diatom cultivated at HRTs of 24, 12, and 6 h had the pseudo-first-order removal (mainly through photodegradation) rate constants of BPA of 0.376, 0.456, and 0.683 h-1, respectively. Under the same experimental condition, the pseudo-first-order removal rate constants of DEET by the frustules cultivated at HRTs of 24, 12, and 6 h increased from 0.270 to 0.330 and to 0.480 h-1.

Synthesis and Antimicrobial Activity of 3D Micro-Nanostructured Diatom Biosilica Coated by Epitaxially Growing Ag-AgCl Hybrid Nanoparticles

The 3D (three-dimensional) micro-nanostructured diatom biosilica obtained from cultivated diatoms was used as a support to immobilize epitaxially growing AgCl-Ag hybrid nanoparticles ((Ag-AgCl)NPs) for the synthesis of nanocomposites with antimicrobial properties. The prepared composites that contained epitaxially grown (Ag-AgCl)NPs were investigated in terms of their morphological and structural characteristics, elemental and mineral composition, crystalline forms, zeta potential, and photoluminescence properties using a variety of instrumental methods including SEM (scanning electron microscopy), TEM (transmission electron microscopy), EDX (energy-dispersive X-ray spectroscopy), XRD (X-ray powder diffraction), zeta-potential measurement, and photoluminescence spectroscopy. The content of (AgCl-Ag)NPs in the hybrid composites amounted to 4.6 mg/g and 8.4 mg/g with AgClNPs/AgNPs ratios as a percentage of 86/14 and 51/49, respectively. Hybrid nanoparticles were evenly dispersed with a dominant size of 5 to 25 nm in composite with an amount of 8.4 mg/g of silver. The average size of the nanoparticles was 7.5 nm; also, there were nanoparticles with a size of 1-2 nm and particles that were 20-40 nm. The synthesis of (Ag-AgCl)NPs and their potential mechanism were studied. The MIC (the minimum inhibitory concentration method) approach was used to investigate the antimicrobial activity against microorganisms Klebsiella pneumoniae, Escherichia coli, and Staphylococcus aureus. The nanocomposites containing (Ag-AgCl)NPs and natural diatom biosilica showed resistance to bacterial strains from the American Type Cultures Collection and clinical isolates (diabetic foot infection and wound isolates).

The pH dependent surface charging and points of zero charge. X. Update

Surfaces are often characterized by their points of zero charge (PZC) and isoelectric points (IEP). Different authors use these terms for different quantities, which may be equal to the actual PZC under certain conditions. Several popular methods lead to results which are inappropriately termed PZC. This present review is limited to zero-points obtained in the presence of inert electrolytes (halides, nitrates, and perchlorates of the 1st group metals). IEP are reported for all kinds of materials. PZC of metal oxides obtained as common intersection points of potentiometric curves for 3 or more ionic strengths (or by means of equivalent methods) are also reported, while the apparent PZC obtained by mass titration, pH-drift method, etc. are deliberately neglected. The results published in the recent publications and older results overlooked in the previous compilations by the same author are reported. The PZC/IEP are accompanied by information on the temperature and on the nature and concentration of supporting electrolyte (if available). The references to previous reviews by the same author allow to compare the newest results with the PZC/IEP of similar materials from the older literature.