Influence of the Geometrical Features of the Cutting Edges of Abrasive Grains on the Removal Efficiency of the Ti6Al4V Titanium Alloy

Ultrathin Carbon Textures Produced on Machined Surfaces in an Integrated Finishing Process Using Microabrasive Films

This study presents research into the unique method of depositing carbon layers onto processed surfaces, during finishing with abrasive films, on a global basis. The authors of this article are holders of the patent for this method. What makes this technology outstanding is that it integrates processes, whereby micro-finishing and the deposition of a carbon layer onto freshly exposed surface fragments is achieved simultaneously, in a single process. Among the main advantages accruable from this process is the reduction of surface irregularities, while the deposition of a carbon layer is achieved simultaneously. Ultrathin graphite layers can be widely used in conditions where other methods of reducing the coefficient of friction are not possible, such as in regard to micromechanisms. This article illustrates the application of carbon coating, end on, on a surface processed with abrasive film, containing intergranular spaces, saturated with graphite. Thin carbon layers were obtained on two substrates that did not contain carbon in their initial composition: soda-lime glass and a tin-bronze alloy. It was performed through microscopic examinations of the produced surface, roughness analyses of these surfaces, and analysis of the chemical compositions determined by two methods, namely EDS and GDOES, proving the existence of the coatings. The aim of this paper is to prove the possibility and efficiency of using graphite-impregnated lapping films in the deposition process of carbon films, with improved surface smoothness, durability, and wear resistance. The produced coatings will be tested in regard to their operational properties in further research. The authors underline the potential of this method to revolutionize surface treatment processes, due to the significant advantages it offers across various industries.

Evaluation of the Surface Topography of Microfinishing Abrasive Films in Relation to Their Machining Capability of Nimonic 80A Superalloy

This study investigates the surface topography of microfinishing abrasive films and their machining capability on the Nimonic 80A superalloy, a high-performance nickel-based alloy commonly used in aerospace and gas turbine engine applications. Surface analysis was conducted on three abrasive films with nominal grain sizes of 30, 15, and 9 μm, exploring wear patterns, contact frequency, and distribution. To assess the distribution of grain apexes, Voronoi cells were employed. Results revealed distinct wear mechanisms, including torn abrasive grains and cracked bond surfaces, highlighting the importance of efficient chip removal mechanisms in microfinishing processes. Larger grain sizes exhibited fewer contacts with the workpiece but provided more storage space for machining products, while smaller grain sizes facilitated smoother surface finishes. The research demonstrated the effectiveness of microfinishing abrasive films in reducing surface irregularities. Additionally, surface analysis of worn abrasive tools provided insights into wear mechanisms and chip formation, with the segmentation of microchips contributing to efficient chip removal. These findings underscore the significance of selecting appropriate abrasive films and implementing effective chip removal mechanisms to optimize microfinishing processes and improve surface finishing quality in advanced material machining applications. It is worth emphasizing that no prior research has investigated the microfinishing of components crafted from Nimonic 80A utilizing abrasive films, rendering this study truly unique in its contribution to the field.

Superfinishing with Abrasive Films Featuring Discontinuous Surfaces

This study introduces innovative designs for abrasive tools aimed at enhancing surface finishing processes. Prototypes consisting of non-continuous abrasive films with discontinuous surface carriers and abrasive layers were developed to improve the efficiency and effectiveness of the smoothing process. Four distinct abrasive films with varying nominal grain sizes were fabricated to explore the versatility and efficacy of the prototypes. The results indicate that the incorporation of carrier irregularities significantly influences surface finishing processes, leading to improvements in material removal efficiency and surface quality. Longitudinal discontinuities facilitate faster removal of irregularities from workpiece materials, reducing the risk of deep scratches on surfaces. Additionally, this study highlights the importance of tool motion patterns in optimizing material removal processes and ensuring surface quality. The integration of carrier irregularities with additional oscillatory tool motion shows promise for further improving surface quality. These findings advance our understanding of abrasive machining processes and provide valuable insights for optimizing abrasive tool designs and machining strategies for enhanced surface finishing.

Selected Aspects of Precision Grinding Processes Optimization

The paper describes selected aspects of the optimization of grinding processes, taking into account the characteristic probabilistic features of this process. Characteristic features of the grinding process that influence the significant dispersion of the quantities used in the optimization process to define goals and limitations are indicated. Attention was paid to the reasons for uncertainty in the use of research results, imperfections in information extraction procedures and the limited amount of data in the use of simulation and regression models in optimization procedures. The issue of determining the durability of abrasive tools in grinding process optimization procedures was analyzed. Methodologies for defining tool life are specified, taking into account the dispersion of the values of controlled process parameters. The effects of interference were taken into account in the relationships describing grinding efficiency and costs. The benefits of optimization taking into account the probabilistic nature of the process were determined.

Analysis of the Process and Results of High-Pressure Abrasive Water Jet Multilayer Cutting of Electrical Steel

Electrical steels are magnetically soft materials and are widely used in the electrical industry for the construction of power transformer cores, distribution transformers, current transformers, and voltage transformers. An important parameter of electrical components, which determines the efficiency of devices, is energy loss during remagnetization. Energy losses are caused by eddy currents, hysteresis, and magnetic delay associated with the low quality of the cut edge after the cutting of steels, and material deformations and excessive stress concentration in the surrounding cutting zones. Common techniques for cutting electrical materials in industrial lines include mechanical cutting and laser cutting. Work has shown that mechanical cutting of electrical steel single layers results in the occurrence of large deformation zones, and in cutting processes with a high-pressure abrasive water jet (AWJ), significant uplifts of material and burrs at the bottom edges of sheets occur. The problem of increasing the cutting quality was solved through selecting the stream parameters for bundle cutting of electrical steels. It has been shown that in the process of cutting electrical sheet bundles, the height of burrs on the cut surface and the zone of plastic deformation are reduced. The work also presents comparison and analysis of characteristic features of the cut edge of electrical sheets obtained through high-pressure abrasive water jet and mechanical cutting processes. The influence of the type and processing parameters on the characteristic features of the material hysteresis loop was determined.

Metrological Aspects of Assessing Surface Topography and Machining Accuracy in Diagnostics of Grinding Processes

The paper presents probabilistic aspects of diagnostics of grinding processes with consideration of metrological aspects of evaluation of topography of machined surfaces and selected problems of assessment of machining accuracy. The processes of creating the geometric structure of the ground surface are described. It was pointed out that the distribution of features important for process diagnostics depends on the mechanism of cumulative effects of random disturbances. Usually, there is a multiplicative mechanism or an additive mechanism of the component vectors of relative displacements of the tool and workpiece. The paper describes a method for determining the classification ability of specific parameters used to evaluate stereometric features of ground surfaces. It is shown that the ability to differentiate the geometric structure of a certain set of surfaces using a selected parameter depends on the geometric mean of the differences in normalized and sorted, consecutive values of this parameter. A methodology is presented for evaluating the ability of various parameters to distinguish different geometric structures of surfaces. Further, on the basis of analyses of a number of grinding processes, a methodology was formulated for proceeding leading to a comprehensive evaluation of machining accuracy and forecasting its results. It was taken into account that in forecasting the accuracy of grinding, it is necessary to determine the deviations, arising under the conditions of multiplicative interaction of the effects of various causes of inaccuracy. Examples are given of processes in which, due to the deformation of the technological system, dependent on the position of the zone and machining force, varying temperature fields and tool wear, the distributions of dimensional deviations are not the realization of stationary processes. It was emphasized that on the basis of the characteristics of the dispersion of the deviation value in the sum set of elements, it is not possible to infer its causes. Only the determination of the "instantaneous" values of the deviation dispersion parameters allows a more complete diagnosis of the process.

Technological Aspects of Variation in Process Characteristics and Tool Condition in Grinding Process Diagnostics

The article presents the technological aspects of the diagnostics of grinding processes. The main features of the grinding process and their importance in diagnostic issues are discussed. Selected issues of research and assessment of the condition of the active surface of grinding wheels are presented. The authors pointed out that the parameters used to assess the topography of the ground surfaces do not have sufficient possibilities to differentiate the surface condition of the grinding wheels. This publication draws attention to the possibility of using new dedicated parameters to assess the properties of the grinding wheel surface. These parameters have a high ability to differentiate changes occurring as a result of the abrasion of grain vertices, their chipping or loading of the grinding wheel surface. The methodology of assessing the processes of abrasive grain wear and changes in the shape and dimensions of the grinding wheel, taking into account the probabilistic features of the grinding process, was formulated. The directions for the development of abrasive tools are presented, pointing to hybrid tools with a multi-phase structure, modified by additions of abrasive aggregates. A new research direction has also been formulated on the use of additive technology to produce specialised abrasive tools, including those with built-in process sensors.

Effects of a New Type of Grinding Wheel with Multi-Granular Abrasive Grains on Surface Topography Properties after Grinding of Inconel 625

Finishing operations are one of the most challenging tasks during a manufacturing process, and are responsible for achieving dimensional accuracy of the manufactured parts and the desired surface topography properties. One of the most advanced finishing technologies is grinding. However, typical grinding processes have limitations in the acquired surface topography properties, especially in finishing difficult to cut materials such as Inconel 625. To overcome this limitation, a new type of grinding wheel is proposed. The tool is made up of grains of different sizes, which results in less damage to the work surface and an enhancement in the manufacturing process. In this article, the results of an experimental study of the surface grinding process of Inconel 625 with single-granular and multi-granular wheels are presented. The influence of various input parameters on the roughness parameter (Sa) and surface topography was investigated. Statistical models of the grinding process were developed based on our research. Studies showed that with an increase in the cutting speed, the surface roughness values of the machined samples decreased (Sa = 0.9 μm for a Vc of 33 m/s for a multigranular wheel). Observation of the grinding process showed an unfavorable effect of a low grinding wheel speed on the machined surface. For both conventional and multigranular wheels, the highest value for the Sa parameter was obtained for Vc = 13 m/s. Regarding the surface topography, the observed surfaces did not show defects over large areas in the cases of both wheels. However, a smaller portion of single traces of active abrasive grains was observed in the case of the multi-granular wheel, indicating that this tool performs better finishing operations.