Quantitative Analysis of Mixed Minerals with Finite Phase Using Thermal Infrared Hyperspectral Technology

Advances in Mineral Processing, Waste Recycling and Extractive Metallurgy

The constant growth of the world economy and industry stimulates an increasing production of ferrous and non-ferrous metals, while the depletion of natural resources leads to demands for the development of new technologies for the processing of low-grade ores and the deep recycling of metallurgical and other anthropogenic wastes [...].

Effects of Ambient Temperature on the Mechanical Properties of Frictionally Welded Components of Polycarbonate and Acrylonitrile Butadiene Styrene Dissimilar Polymer Rods

Rotary friction welding (RFW) has no electric arc and the energy consumption during welding can be reduced as compared with conventional arc welding since it is a solid-phase welding process. The RFW is a sustainable manufacturing process because it provides low environmental pollution and energy consumption. However, few works focus on the reliability of dissimilar polymer rods fabricated via RFW. The reliability of the frictionally welded components is also related to the ambient temperatures. This work aims to investigate the effects of ambient temperature on the mechanical properties of frictionally welded components of polycarbonate (PC) and acrylonitrile butadiene styrene (ABS) dissimilar polymer rods. It was found that the heat-affected zone width increases with increasing rotational speeds due to peak welding temperature. The Shore A surface hardness of ABS/PC weld joint does not change with the increased rotational speeds. The Shore A surface hardness in the weld joint of RFW of the ABS/PC is about Shore A 70. The bending strength was increased by about 53% when the welded parts were placed at 60-70 °C compared with bending strength at room temperature. The remarkable finding is that the bending fracture position of the weldment occurs on the ABS side. It should be pointed out that the bending strength can be determined by the placed ambient temperature according to the proposed prediction equation. The impact energy was decreased by about 33% when the welded parts were placed at 65-70 °C compared with the impact energy at room temperature. The impact energy (y) can be determined by the placed ambient temperature according to the proposed prediction equation. The peak temperature in the weld interface can be predicted by the rotational speed based on the proposed equation.

Fatigue Behavior of Rotary Friction Welding of Acrylonitrile Butadiene Styrene and Polycarbonate Dissimilar Materials

Understanding the fatigue behaviors of weld joints is significant in engineering practice. Rotary friction welding (RFW) can join the additively manufactured polymer components. Until now, no research has focused on the fatigue behavior of polymer components jointed via RFW. This study investigates the fatigue life of ABS/PC dissimilar components fabricated via RFW and proposes the fatigue mechanism based on the failure structure. This work uses five different cyclic loads and rotational speeds to investigate the fatigue life. The fatigue life of the RFW of ABS/PC dissimilar rods is better compared with the pure ABS and pure PC specimens due to weld and integrity microstructural changes resulting from the combination of ABS and PC materials. The number of cycles until the rupture of RFW of ABS/PC dissimilar components (y) can be determined by the cyclic load (x) according to the prediction equation of y = -838.25x2 - 2035.8x + 67,262. The fatigue life of the RFW of ABS/PC dissimilar components increase with the increased rotational speed. The number of cycles until rupture (y) can be determined by the different rotational speeds (x) according to the prediction equation of y = 315.21x2 + 2710.4x + 32,124.

Experimentation and Numerical Modeling of Peak Temperature in the Weld Joint during Rotary Friction Welding of Dissimilar Plastic Rods

Rotary friction welding (RFW) could result in lower welding temperature, energy consumption, or environmental effects as compared with fusion welding processes. RFW is a green manufacturing technology with little environmental pollution in the field of joining methods. Thus, RFW is widely employed to manufacture green products. In general, the welding quality of welded parts, such as tensile strength, bending strength, and surface hardness is affected by the peak temperature in the weld joint during the RFW of dissimilar plastic rods. However, hitherto little is known about the domain knowledge of RFW of acrylonitrile butadiene styrene (ABS) and polycarbonate (PC) polymer rods. To prevent random efforts and energy consumption, a green method to predict the peak temperature in the weld joint of dissimilar RFW of ABS and PC rods was proposed. The main objective of this work is to investigate the peak temperature in the weld joint during the RFW using COMSOL multiphysics software for establishing an empirical technical database of RFW of dissimilar polymer rods under different rotational speeds. The main findings include that the peak temperature affecting the mechanical properties of RFW of PC and ABS can be determined by the simulation model proposed in this work. The average error of predicting the peak temperature using COMSOL software for five different rotational speeds is about 15 °C. The mesh element count of 875,688 is the optimal number of meshes for predicting peak temperature in the weld joint. The bending strength of the welded part (y) using peak welding temperature (x) can be predicted by the equation of y = -0.019 x² + 5.081x - 200.75 with a correlation coefficient of 0.8857. The average shore A surface hardness, impact energy, and bending strength of the welded parts were found to be increased with increasing the rotational speed of RFW.