Polymer Electrolyte Membranes for Water Photo-Electrolysis

Water Splitting with Enhanced Efficiency Using a Nickel-Based Co-Catalyst at a Cupric Oxide Photocathode

Homemade non-critical raw materials such as Ni or NiCu co-catalysts were added at the photocathode of a tandem cell, constituted by photoelectrodes made of earth-abundant materials, to generate green solar hydrogen from photoelectrochemical water splitting. Oxygen evolving at the Ti-and-P-doped hematite/TCO-based photoanode and hydrogen at the cupric oxide/GDL-based photocathode are separated by an anion exchange polymer electrolyte membrane placed between them. The effect of the aforementioned co-catalysts was studied in a complete PEC cell in the presence of the ionomer dispersion and the anionic membrane to evaluate their impact under practical conditions. Notably, different amounts of Ni or NiCu co-catalysts were used to improve the hydrogen evolution reaction (HER) kinetics and the overall solar-to-hydrogen (STH) efficiency of the photoelectrochemical cells. At −0.6 V, in the bias-assisted region, the photocurrent density reaches about 2 mA cm−2 for a cell with 12 µg cm−2 of Ni loading, followed by 1.75 mA cm−2 for the cell configuration based on 8 µg cm−2 of NiCu. For the best-performing cell, enthalpy efficiency at −0.4 V reaches a first maximum value of 2.03%. In contrast, the throughput efficiency, which is a ratio between the power output and the total power input (solar + electric) provided by an external source, calculated at −1.225 V, reaches a maximum of 10.75%. This value is approximately three times higher than the best results obtained in our previous studies without the use of co-catalysts at the photocathode.

Anionic Exchange Membrane for Photo-Electrolysis Application

Tandem photo-electro-chemical cells composed of an assembly of a solid electrolyte membrane and two low-cost photoelectrodes have been developed to generate green solar fuel from water-splitting. In this regard, an anion-exchange polymer-electrolyte membrane, able to separate H₂ evolved at the photocathode from O₂ at the photoanode, was investigated in terms of ionic conductivity, corrosion mitigation, and light transmission for a tandem photo-electro-chemical configuration. The designed anionic membranes, based on polysulfone polymer, contained positive fixed functionalities on the side chains of the polymeric network, particularly quaternary ammonium species counterbalanced by hydroxide anions. The membrane was first investigated in alkaline solution, KOH or NaOH at different concentrations, to optimize the ion-exchange process. Exchange in 1M KOH solution provided high conversion of the groups, a high ion-exchange capacity (IEC) value of 1.59 meq/g and a hydroxide conductivity of 25 mS/cm at 60 °C for anionic membrane. Another important characteristic, verified for hydroxide membrane, was its transparency above 600 nm, thus making it a good candidate for tandem cell applications in which the illuminated photoanode absorbs the highest-energy photons (< 600 nm), and photocathode absorbs the lowest-energy photons. Furthermore, hydrogen crossover tests showed a permeation of H₂ through the membrane of less than 0.1%. Finally, low-cost tandem photo-electro-chemical cells, formed by titanium-doped hematite and ionomer at the photoanode and cupric oxide and ionomer at the photocathode, separated by a solid membrane in OH form, were assembled to optimize the influence of ionomer-loading dispersion. Maximum enthalpy (1.7%), throughput (2.9%), and Gibbs energy efficiencies (1.3%) were reached by using n-propanol/ethanol (1:1 wt.) as solvent for ionomer dispersion and with a 25 µL cm^-2 ionomer loading for both the photoanode and the photocathode.

Dry Hydrogen Production in a Tandem Critical Raw Material-Free Water Photoelectrolysis Cell Using a Hydrophobic Gas-Diffusion Backing Layer

A photoelectrochemical tandem cell (PEC) based on a cathodic hydrophobic gas-diffusion backing layer was developed to produce dry hydrogen from solar driven water splitting. The cell consisted of low cost and non-critical raw materials (CRMs). A relatively high-energy gap (2.1 eV) hematite-based photoanode and a low energy gap (1.2 eV) cupric oxide photocathode were deposited on a fluorine-doped tin oxide glass (FTO) and a hydrophobic carbonaceous substrate, respectively. The cell was illuminated from the anode. The electrolyte separator consisted of a transparent hydrophilic anionic solid polymer membrane allowing higher wavelengths not absorbed by the photoanode to be transmitted to the photocathode. To enhance the oxygen evolution rate, a NiFeOX surface promoter was deposited on the anodic semiconductor surface. To investigate the role of the cathodic backing layer, waterproofing and electrical conductivity properties were studied. Two different porous carbonaceous gas diffusion layers were tested (Spectracarb® and Sigracet®). These were also subjected to additional hydrophobisation procedures. The Sigracet 35BC® showed appropriate ex-situ properties for various wettability grades and it was selected as a cathodic substrate for the PEC. The enthalpic and throughput efficiency characteristics were determined, and the results compared to a conventional FTO glass-based cathode substrate. A throughput efficiency of 2% was achieved for the cell based on the hydrophobic backing layer, under a voltage bias of about 0.6 V, compared to 1% for the conventional cell. For the best configuration, an endurance test was carried out under operative conditions. The cells were electrochemically characterised by linear polarisation tests and impedance spectroscopy measurements. X-Ray Diffraction (XRD) patterns and Scanning Electron Microscopy (SEM) micrographs were analysed to assess the structure and morphology of the investigated materials.

Enhanced Photoelectrochemical Water Splitting at Hematite Photoanodes by Effect of a NiFe-Oxide co-Catalyst

Tandem photoelectrochemical cells (PECs), made up of a solid electrolyte membrane between two low-cost photoelectrodes, were investigated to produce “green” hydrogen by exploiting renewable solar energy. The assembly of the PEC consisted of an anionic solid polymer electrolyte membrane (gas separator) clamped between an n-type Fe2O3 photoanode and a p-type CuO photocathode. The semiconductors were deposited on fluorine-doped tin oxide (FTO) transparent substrates and the cell was investigated with the hematite surface directly exposed to a solar simulator. Ionomer dispersions obtained from the dissolution of commercial polymers in the appropriate solvents were employed as an ionic interface with the photoelectrodes. Thus, the overall photoelectrochemical water splitting occurred in two membrane-separated compartments, i.e., the oxygen evolution reaction (OER) at the anode and the hydrogen evolution reaction (HER) at the cathode. A cost-effective NiFeOx co-catalyst was deposited on the hematite photoanode surface and investigated as a surface catalytic enhancer in order to improve the OER kinetics, this reaction being the rate-determining step of the entire process. The co-catalyst was compared with other well-known OER electrocatalysts such as La0.6Sr0.4Fe0.8CoO3 (LSFCO) perovskite and IrRuOx. The Ni-Fe oxide was the most promising co-catalyst for the oxygen evolution in the anionic environment in terms of an enhanced PEC photocurrent and efficiency. The materials were physico-chemically characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM) and scanning electron microscopy (SEM).

Solar Hydrogen Generation from Ambient Humidity Using Functionalized Porous Photoanodes

Solar hydrogen is a promising sustainable energy vector, and steady progress has been made in the development of photoelectrochemical (PEC) cells. Most research in this field has focused on using acidic or alkaline liquid electrolytes for ionic transfer. However, the performance is limited by (i) scattering of light and blocking of catalytic sites by gas bubbles and (ii) mass transport limitations. An attractive alternative to a liquid water feedstock is to use the water vapor present as humidity in ambient air, which has been demonstrated to mitigate the above problems and can expand the geographical range where these devices can be utilized. Here, we show how the functionalization of porous TiO₂ and WO₃ photoanodes with solid electrolytes-proton conducting Aquivion and Nafion ionomers-enables the capture of water from ambient air and allows subsequent PEC hydrogen production. The optimization strategy of photoanode functionalization was examined through testing the effect of ionomer loading and the ionomer composition. Optimized functionalized photoanodes operating at 60% relative humidity (RH) and T_cell = 30-70 °C were able to recover up to 90% of the performance obtained at 1.23 V versus reverse hydrogen electrode (RHE) when water is introduced in the liquid phase (i.e., conventional PEC operation). Full performance recovery is achieved at a higher applied potential. In addition, long-term experiments have shown remarkable stability at 60% RH for 64 h of cycling (8 h continuous illumination-8 h dark), demonstrating that the concept can be applicable outdoors.

Toward Tandem Solar Cells for Water Splitting Using Polymer Electrolytes

Tandem photoelectrochemical cells, formed by two photoelectrodes with complementary light absorption, have been proposed to be a viable approach for obtaining clean hydrogen. This requires the development of new designs that allow for upscaling, which would be favored by the use of transparent polymer electrolyte membranes (PEMs) instead of conventional liquid electrolytes. This article focuses on the photoelectrochemical performance of a water-splitting tandem cell based on a phosphorus-modified α-Fe₂O₃ photoanode and on an iron-modified CuO photocathode, with the employment of an alkaline PEM. Such a photoelectrochemical cell works even in the absence of bias, although significant effort should be directed to the optimization of the photoelectrode/PEM interface. In addition, the results reveal that the employment of polymer electrolytes increases the stability of the device, especially in the case of the photocathode.