Phase Transformations upon Ageing in Ti15Mo Alloy Subjected to Two Different Deformation Methods

The Determining Influence of the Phase Composition on the Mechanical Properties of Titanium-Iron Alloys after High-Pressure Torsion

Three titanium alloys with 0.5, 6, and 9 wt.% iron were investigated, and the samples were pre-annealed in three different regions of the Ti-Fe phase diagram, namely β, α+β, and α+FeTi. After annealing, five samples of different phases and structural compositions were studied. They were then subjected to the high-pressure torsion (HPT). The microstructure of the samples before and after HPT treatment was studied using transmission and scanning electron microscopy. The microstructure of the samples obtained during heat treatment before HPT treatment had a fundamental effect on the microstructure after HPT. Grain boundary layers and chains of particles formed during the annealing process made it difficult to mix the material during HPT, which led to the formation of areas with non-uniform mixing of components. Thus, the grain boundary layers of the α-phase formed in the Ti-6wt % Fe alloy after annealing at 670 °C significantly decreased the mixing of the components during HPT. Despite the fact that the microstructure and phase composition of Ti-6wt % Fe alloys pre-annealed in three different regions of the Ti-Fe phase diagram had significant differences, after HPT treatment, the phase compositions of the studied samples were quite similar. Moreover, the measured micro- and nanohardness as well as the Young's modulus of Ti-6wt % Fe alloy had similar values. It was shown that the microhardness of the studied samples increased with the iron content. The values of nanohardness and Young's modulus correlated well with the fractions of β- and ω-phases in the studied alloys.

Effect of Cold-Rolling Deformation on the Microstructural and Mechanical Properties of a Biocompatible Ti-Nb-Zr-Ta-Sn-Fe Alloy

The primary focus of the current paper centers on the microstructures and mechanical properties exhibited by a Ti-30Nb-12Zr-5Ta-2Sn-1.25Fe (wt. %) (TNZTSF) alloy that has been produced through an intricate synthesis process comprising cold-crucible induction in levitation, carried out in an atmosphere controlled by argon, and cold-rolling deformation (CR), applying systematic adjustments in the total deformation degree (total applied thickness reduction), spanning from 10% to 60%. The microstructural characteristics of the processed specimens were investigated by SEM and XRD techniques, and the mechanical properties by tensile and microhardness testing. The collected data indicate that the TNZTSF alloy's microstructure, in the as-received condition, consists of a β-Ti phase, which shows polyhedral equiaxed grains with an average grain size close to 82.5 µm. During the cold-deformation processing, the microstructure accommodates the increased applied deformation degree by increasing crystal defects such as sub-grain boundaries, dislocation cells, dislocation lines, and other crystal defects, powerfully affecting the morphological characteristics. The as-received TNZTSF alloy showed both high strength (i.e., ultimate tensile strength close to σUTS = 705.6 MPa) and high ductility (i.e., elongation to fracture close to εf = 11.1%) properties, and the computed β-Ti phase had the lattice parameter a = 3.304(7) Å and the average lattice microstrain ε = 0.101(3)%, which are drastically influenced by the applied cold deformation, increasing the strength properties and decreasing the ductility properties due to the increased crystal defects density. Applying a deformation degree close to 60% leads to an ultimate tensile strength close to σUTS = 1192.1 MPa, an elongation to fracture close to εf = 7.9%, and an elastic modulus close to 54.9 GPa, while the computed β-Ti phase lattice parameter becomes a = 3.302(1) Å.

Microstructure and Mechanical Properties of β-Titanium Ti-15Mo Alloy Produced by Combined Processing including ECAP-Conform and Drawing

At present, researchers pay great attention to the development of metastable β-titanium alloys. A task of current importance is the enhancement of their strength and fatigue properties. An efficient method for increasing the strength of such alloys could be severe plastic deformation. The object of this study was a medical metastable β-titanium alloy Ti-15Mo (ASTM F2066). The alloy in the (α + β) state was for the first time deformed by combined processing, including equal channel angular pressing-conform and drawing. Such processing enabled the production of long-length rods with a length of 1500 mm. The aim of the work was to study the effect of the combined processing on the alloy's microstructure and mechanical properties. An ultrafine-grained structure with an average size of structural elements less than 100 nm was obtained. At the same time, high strength and ductility (σ_uts = 1590 MPa, δ = 10%) were achieved, which led to a record increase in the endurance limit (σ_-1 = 710 MPa) under tension-compression terms.

Evolution of Microstructural and Mechanical Properties during Cold-Rolling Deformation of a Biocompatible Ti-Nb-Zr-Ta Alloy

In this study, a Ti-32.9Nb-4.2Zr-7.5Ta (wt%) titanium alloy was produced by melting in a cold crucible induction in a levitation furnace, and then deforming by cold rolling, with progressive deformation degrees (thickness reduction), from 15% to 60%, in 15% increments. The microstructural characteristics of the specimens in as-received and cold-rolled conditions were determined by XRD and SEM microscopy, while the mechanical characteristics were obtained by tensile and microhardness testing. It was concluded that, in all cases, the Ti-32.9Nb-4.2Zr-7.5Ta (wt%) showed a bimodal microstructure consisting of Ti-β and Ti-α″ phases. Cold deformation induced significant changes in the microstructural and the mechanical properties, leading to grain-refinement, crystalline cell distortions and variations in the weight-fraction ratio of both Ti-β and Ti-α″ phases, as the applied degree of deformation increased from 15% to 60%. Changes in the mechanical properties were also observed: the strength properties (ultimate tensile strength, yield strength and microhardness) increased, while the ductility properties (fracture strain and elastic modulus) decreased, as a result of variations in the weight-fraction ratio, the crystallite size and the strain hardening induced by the progressive cold deformation in the Ti-β and Ti-α″ phases.