High Catalytic Efficiency of Nanostructured β-CoMoO₄ in the Reduction of the Ortho-, Meta- and Para-Nitrophenol Isomers

Cobalt molybdate hollow spheres decorated graphitic carbon nitride sheets for electrochemical sensing of dimetridazole

In the present work, a cobalt molybdate (CoMoO4) hollow spheres-incorporated graphitic carbon nitride (g-CN) composite is prepared for the electrochemical detection of dimetridazole (DZ). The synergistic effect between the hollow-structured CoMoO4 and g-CN nanosheets facilitates the transportation of electrons through kinetic barriers, thereby providing a high electrical conductivity with increased electroactive sites. The proposed CoMoO4@g-CN-modified electrode displayed a wide linear range (0.001-492.77 μM) and a lower detection limit (LOD: 0.4 nM) for the determination of DZ through the amperometry (i-t) method. In addition, the CoMoO4@g-CN-modified electrode achieved good operational stability, anti-interfering ability (five-fold excess amount of co-interfering compounds) and reproducibility. These results demonstrate the increased electrocatalytic activity of CoMoO4@g-CN modified glassy carbon electrode (GCE) towards the detection of DZ in food samples with satisfactory recovery ranges.

Gold and palladium supported on an ionic liquid modified Fe-based metal-organic framework (MOF) as highly efficient catalysts for the reduction of nitrophenols, dyes and Sonogashira-Hagihara reactions

Two supported noble metal species, gold and palladium anchored on an ionic liquid-modified Fe-based metal-organic framework (MOF), were successfully synthesized and characterized by FT-IR, XRD, TEM, XPS, SEM, EDX, and elemental mapping. The ionic liquid post-modified MOF was used for anchoring Au or Pd at ppm levels, and the resulting materials were employed as catalysts in the reduction of nitrophenol isomers, dyes, and Sonogashira-Hagihara reactions. Using the Au@Fe-MOF-IL catalyst, reduction of nitrophenol isomers, as well as the reductive degradation of dyes, e.g., methylene blue (MB), methyl orange (MO), and methyl red (MR) were performed efficiently in water. On the other hand, Pd@Fe-MOF-IL was used as an effective catalyst in the Sonogashira-Hagihara coupling reaction of aryl iodides and bromides using very low amounts of Pd. These catalysts were recycled and reused for several runs without deteriorating remarkably in catalytic performance.

Improved Brønsted to Lewis (B/L) Ratio of Co- and Mo-Impregnated ZSM-5 Catalysts for Palm Oil Conversion to Hydrocarbon-Rich Biofuels

The purposes of this study are to investigate the effect of metal (Co and Mo) impregnation to ZSM-5 catalysts on the Brønsted to Lewis (B/L) ratio as the active sites of cracking reaction, and the catalysts’ performance testing for palm oil cracking to produce hydrocarbon-rich biofuels. Both metals were impregnated on the ZSM-5 catalyst using a wet-impregnation method. The catalysts were characterized using X-ray diffraction (XRD), X-ray Fluorescence (XRF), Scanning Electron Microscopy (SEM), Brunauer–Emmett–Teller (BET), and Pyridine-probed Fourier-Transform Infrared (Py-FTIR) spectroscopy methods. The catalysts were tested on the cracking process of palm oil to biofuels in a continuous fixed-bed catalytic reactor. In order to determine the composition of the organic liquid product (OLP, biofuels), the product was analyzed using a gas chromatography-mass spectrometry (GC-MS) method. The results showed that the co-impregnation of Co and Mo to ZSM-5 highly increased the Brønsted to Lewis acid site (B/L) ratio, although the total number of acid sites decreased. However, the impregnation of Co and Mo on the ZSM-5 decreased the surface area of catalysts due to pore blocking by metals, while the B/L ratio of the catalysts increased. It was obtained that by utilizing Co- and Mo-impregnated ZSM-5 catalysts, the hydrocarbons product selectivity increased from 84.32% to 95.26%; however, the yield of biofuels decreased from 67.57% to 41.35%. The increase in hydrocarbons product selectivity was caused by the improvement of the Brønsted to Lewis (B/L) acid sites ratio.

Highly Efficient Methylene Blue Dye Removal by Nickel Molybdate Nanosorbent

Removing methylene blue (MB) dye from aqueous solutions was examined by the use of nickel molybdate (α-NiMoO₄) as an adsorbent produced by an uncomplicated, rapid, and cost-effective method. Different results were produced by varying different parameters such as the pH, the adsorbent dose, the temperature, the contact time, and the initial dye concentration. Adsorbent dose and pH had a major removal effect on MB. Interestingly, a lower amount of adsorbent dose caused greater MB removal. The amount of removal gained was efficient and reached a 99% level with an initial methylene blue solution concentration of ≤160 ppm at pH 11. The kinetic studies indicated that the pseudo-second-order kinetic model relates very well with that of the obtained experimental results. The thermodynamic studies showed that removing the MB dye was favorable, spontaneous, and endothermic. Impressively, the highest quantity of removal amount of MB dye was 16,863 mg/g, as shown by the Langmuir model. The thermal regeneration tests revealed that the efficiency of removing MB (11,608 mg/g) was retained following three continuous rounds of recycled adsorbents. Adsorption of MB onto α-NiMoO₄ nanoparticles and its regeneration were confirmed by Fourier transform infrared spectroscopy (FTIR) analysis and scanning electron microscopy (SEM) analysis. The results indicated that α-NiMoO₄ nanosorbent is an outstanding and strong candidate that can be used for removing the maximum capacity of MB dye in wastewater.

Iron Molybdate Fe2(MoO4)3 Nanoparticles: Efficient Sorbent for Methylene Blue Dye Removal from Aqueous Solutions

The present study investigated iron molybdate (Fe₂(MoO₄)₃), synthesized via a simple method, as a nanosorbent for methylene blue (MB) dye removal from aqueous solutions. Investigations of the effects of several parameters like contact time, adsorbent dose, initial dye concentration, temperature and pH were carried out. The results showed that MB removal was affected, significantly, by adsorbent dose and pH. Interestingly, lower values of adsorbent dose resulted in the removal of higher amounts of MB. At the optimum pH, the removal efficiency of 99% was gained with an initial MB concentration of ≤60 ppm. The kinetic study specified an excellent correlation of the experimental results with the pseudo-second-order kinetics model. Thermodynamic studies proved a spontaneous, favorable and endothermic removal. The maximum amount of removal capacity of MB dye was 6173 mg/g, which was determined from the Langmuir model. The removal efficiency was shown to be retained after three cycles of reuse, as proven by thermal regeneration tests. The presence and adsorption of the dye onto the Fe₂(MoO₄)₃ nanoparticle surface, as well as the regeneration of the latter, was ascertained by scanning electron microscopy (SEM) and Fourier-transform infrared spectroscopy (FTIR). These findings are indicative that the investigated nanosorbent is an excellent candidate for the removal of MB in wastewater.

Sonication-Assisted Synthesis of Bimetallic Hg/Pd Alloy Nanoparticles for Catalytic Reduction of Nitrophenol and its Derivatives

In this article, we report a facile approach for the synthesis of an inexpensive catalyst of bimetallic Hg/Pd alloys comprising nanoparticles with various structures using a unique ultrasonic reaction that is conducted without the use of any reducing agent. The nanoparticles of Hg/Pd alloys (HgPd and Hg₂Pd₅) were achieved for the first time by sonicating an aqueous solution of Palladium (II) nitrate with metallic liquid mercury, as evidenced by XRD. EDS further confirmed the presence of Pd and Hg elements in the alloy. The surface morphology and structure of the nanoparticles have been systematically investigated by HRSEM, HRTEM and SAED pattern. In order to explore the catalytic activity of the as-synthesized nanoalloys, the catalytic reduction of 4-nitrophenol and a few other nitrophenol derivatives were investigated. Excellent catalytic activity was obtained for Hg/Pd (1:1) alloy, and the rate constant for the reduction of 4-NP with Hg/Pd at room temperature was found to be 58.4 × 10^-3 s^-1, which is possibly the highest ever reported. The catalyst exhibited superior stability and reusability when compared with those reported in the literature for other catalysts based on noble metals.

Synergistic engineering of architecture and composition in NixCo1-xMoO4@CoMoO4 nanobrush arrays towards efficient overall water splitting electrocatalysis

Implementing the hierarchical structures of non-noble-metal-based electrocatalysts and modulating their composition can help accelerate surface reactions and fulfill the promise of renewable energy devices via water splitting. Herein, molybdenum-based compounds are constructed on activated nickel foam (act-NF) by a one-step hydrothermal growth. The product generated on the act-NF is Ni_xCo_1-xMoO₄@CoMoO₄, with a novel 3D hierarchical heterostructure, wherein the one-dimensional CoMoO₄ nanorods are hierarchically integrated with the two-dimensional Ni_xCo_1-xMoO₄ nanosheets (NCMO@CMO/act-NF). The formation of Ni_xCo_1-xMoO₄@CoMoO₄ attributes to the release and diffusion of Ni²⁺ from act-NF. Heterogeneous Ni_xCo_1-xMoO₄@CoMoO₄ has compositional differences, and synergistic interaction between cobalt and nickel results in the modulated electronic states. Meanwhile, the hierarchical structure facilitates the exposure of active sites. Combining these two advantages, NCMO@CMO/act-NF presents a low η₁₀ value of 61 and 180 mV in 1.0 M KOH for the HER and OER, respectively, and it shows a low cell voltage of 1.46 V for overall water splitting with robust stability. DFT calculations reveal that Ni doping leads to the charge depletion of Co, which further optimizes the d-band center of metal sites and tunes the adsorption of adsorbates to facilitate the water splitting reaction. Thus, a promising strategy of incorporating the nanostructure design with compositional modulation is presented to develop functional materials for energy conversion.

Carbon dot-decorated porous organic cage as fluorescent sensor for rapid discrimination of nitrophenol isomers and chiral alcohols

Isomers discrimination plays a vital role in modern chemistry, and development of efficient and rapid method to achieve this aim has attracted a great deal of interest. In this work, a novel carbon dot-decorated chiral porous organic cage hybrid nanocomposite (CD@RCC3) was prepared and used to fabricate fluorescent sensor. The resultant CD@RCC3 was characterized by using a range of techniques, finding that CD@RCC3 possesses strong and stable fluorescent property in common organic solvents, especially it exhibits chiral property. The potential application of CD@RCC3 in fluorescence sensing was demonstrated by isomers discrimination. The designed sensor was successfully used to rapid discriminate nitrophenol isomers. Meanwhile, it exhibited differentiation ability towards phenylalaninol and phenylethanol enantiomers. Our work enriches the type of synthetic materials for fluorescence sensing, and provides a simple method for distinguishing structural isomers and chiral isomers.

Preparation and Characterization of α-Zinc Molybdate Catalyst: Efficient Sorbent for Methylene Blue and Reduction of 3-Nitrophenol

Zinc molybdate (ZnMoO₄) was prepared by thermal decomposition of an oxalate complex under a controlled temperature of 500 °C. Analyses of the oxalate complex were carried out using Fourier transform infrared spectroscopy (FTIR) and thermogravimetric analysis (TGA). On the other hand, analyses of the synthesized zinc molybdate were carried out by X-ray diffraction (XRD), transmission electron microscopy (TEM), and Brunauer-Emmett-Teller technique (BET). The efficiency of the synthesized catalyst was tested with the reduction reaction of 3-nitrophenol (3-NP), and was also applied as a sorbent for methylene blue dye (MB) in aqueous solutions. The catalytic test of zinc molybdate shows a very high activity. The concentration reduction progress and adsorption of the dye were followed by an ultraviolet-visible (UV-vis) spectrophotometer.