Biochar of Spent Coffee Grounds as Per Se and Impregnated with TiO2: Promising Waste-Derived Adsorbents for Balofloxacin

Valorization and Upcycling of Acid Mine Drainage and Plastic Waste via the Preparation of Magnetic Sorbents for Adsorption of Emerging Contaminants

Plastic waste poses a serious environmental risk, but it can be recycled to produce a variety of nanomaterials for water treatment. In this study, poly(ethylene terephthalate) (PET) waste and acid mine drainage were used in the preparation of magnetic mesoporous carbon (MMC) nanocomposites for the adsorptive removal of pharmaceuticals and personal care products (PPCPs) from water samples. The latter were then characterized using Fourier transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD), scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDX), transmission electron microscopy (TEM), Brunauer-Emmett-Teller (BET), and ζ potential. The results of Brunauer-Emmett-Teller isotherms revealed high specific surface areas of 404, 664, and 936 m2/g with corresponding pore sizes 2.51, 2.28, and 2.26 nm for MMC, MMAC-25%, and MMAC-50% adsorbents, respectively. Under optimized conditions, the equilibrium studies were best described by the Langmuir and Freundlich models and kinetics by the pseudo-second-order model. The maximum adsorption capacity for monolayer adsorption from the Langmuir model was 112, 102, and 106 mg/g for acetaminophen, caffeine, and carbamazepine, respectively. The composites could be reused for up to six cycles without losing their adsorption efficiency. Furthermore, prepared adsorbents were used to remove acetaminophen, caffeine, and carbamazepine from wastewater samples, and up to a 95% removal efficiency was attained.

High efficient COVID-19 waste co-pyrolysis char/TiO2 nanocomposite for photocatalytic reduction of Cr(VI) under visible light

Titanium dioxide (Titania) nanoparticle-coated biochar derived through co-pyrolysis of COVID-19 waste face mask (WFM) and Moringa oleifera seed cake (MO) provides an effective way to alleviate toxic metal in wastewater. This study investigates the effects of Biochar/titania photocatalyst preparation, characterization, and its photoreduction of Cr(VI). The morphological and functional modifications in the catalyst were identified using X-Ray diffraction, scanning electron microscopy, Fourier transform infrared spectroscopy, ultraviolet spectrophotometer, surface area analysis, and Raman spectrophotometer, respectively. The influencing parameters, namely, pH, photocatalyst dosage, initial pollutant concentration, and visible light irradiation time, have been investigated. The findings reveal that the Cr(VI) reduction by the photocatalyst was highly facilitated by photocatalytic process. The prepared photocatalyst shows higher and faster reduction rate of Cr(VI) and also improves the catalyst stability. The photoreduction of Cr(VI) ensembles well with pseudo-first order kinetics. At 180 min of reaction time, maximum Cr(VI) reduction of 98.65% was achieved at pH 2, 0.3 g/L catalyst dosage, and 10 ppm initial concentration, respectively. The synthesized photocatalyst shows excellent recycling performance up to 7 times, and these studies proved that the prepared catalyst is cost-effective and efficiently employed for removing pollutants.

A portable electrochemical immunosensor for ovarian cancer uses hierarchical microporous carbon material from waste coffee grounds

A simple label-free electrochemical immunosensor for ovarian cancer (OC) detection was developed using a hierarchical microporous carbon material fabricated from waste coffee grounds (WCG). The analysis method exploited near-field communication (NFC) and a smartphone-based potentiostat. Waste coffee grounds were pyrolyzed with potassium hydroxide and used to modify a screen-printed electrode. The modified screen-printed electrode was decorated with gold nanoparticles (AuNPs) to capture a specific antibody. The modification and immobilization processes were characterized by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The sensor had an effective dynamic range of 0.5 to 50.0 U mL^-1 of cancer antigen 125 (CA125) tumor marker with a correlation coefficient of 0.9995. The limit of detection (LOD) was 0.4 U mL^-1. A comparison of the results obtained from human serum analysis with the proposed immunosensor and the results obtained from the clinical method confirmed the accuracy and precision of the proposed immunosensor.

Performance of Pristine versus Magnetized Orange Peels Biochar Adapted to Adsorptive Removal of Daunorubicin: Eco-Structuring, Kinetics and Equilibrium Studies

Drugs and pharmaceuticals are an emergent class of aquatic contaminants. The existence of these pollutants in aquatic bodies is currently raising escalating concerns because of their negative impact on the ecosystem. This study investigated the efficacy of two sorbents derived from orange peels (OP) biochar (OPBC) for the removal of the antineoplastic drug daunorubicin (DNB) from pharmaceutical wastewater. The adsorbents included pristine (OPBC) and magnetite (Fe₃O₄)-impregnated (MAG-OPBC) biochars. Waste-derived materials offer a sustainable and cost-effective solution to wastewater bioremediation. The results showed that impregnation with Fe₃O₄ altered the crystallization degree and increased the surface area from 6.99 m²/g in OPBC to 60.76 m²/g in the case of MAG-OPBC. Placket-Burman Design (PBD) was employed to conduct batch adsorption experiments. The removal efficiency of MAG-OPBC (98.51%) was higher compared to OPBC (86.46%). DNB adsorption onto OPBC followed the D-R isotherm, compared to the Langmuir isotherm in the case of MAG-OPBC. The maximum adsorption capacity (q_max) was 172.43 mg/g for MAG-OPBC and 83.75 mg/g for OPBC. The adsorption kinetics for both sorbents fitted well with the pseudo-second-order (PSO) model. The results indicate that MAG-OPBC is a promising adsorbent for treating pharmaceutical wastewater.

Trends in removal of pharmaceuticals in contaminated water using waste coffee and tea-based materials with their derivatives

The introduction of large amounts of pharmaceuticals into the environmental waters is well-documented in literature with their occurrence reported in all different water matrices accessible to humans and animals. At the same time, the increasing consumption of coffee and tea-based beverages results in the generation of solid waste, which is mostly disposed-off in the environment. To minimize environmental pollution, coffee and tea-based materials have been proposed as suitable options to remove pharmaceuticals in environmental waters. Therefore, this article provides a critical review on the preparation and applications of coffee and tea-based materials in removing pharmaceuticals from contaminated water. In this context, most studies in literature focused on the applications of these materials as adsorbents, while only limited work on their role in degradation of pharmaceuticals is discussed. The successful application in adsorption studies is attributed to high surface areas of adsorbents and the ability to easily modify the adsorbent surfaces by incorporating functional groups that provide additional oxygen atoms, which promote easy interactions with pharmaceuticals. Hence, the adsorption mechanisms are mostly described by hydrogen bonding, electrostatic and π-π interactions with sample pH playing a dominant role in the adsorption process. Overall, the present article focused on the developments, trends and future research direction on the preparations and applications of coffee and tea-based materials for efficient removal of pharmaceuticals in water. PRACTITIONER POINTS: Review of tea and coffee wastes application for removal of pharmaceuticals in water Key applications in adsorption and degradation of pharmaceuticals in water Removal mostly explained by hydrogen bonding, electrostatic, and π-π interactions Trends, gaps, and future research to be explored are reviewed and highlighted.

Application of Cyanobacteria Arthospira platensis for Bioremediation of Erbium-Contaminated Wastewater

Erbium belongs to rare earth elements critical for industry, especially nuclear technology. Cyanobacteria Arthospira platensis was used for Er(III) removal from wastewater by applying biosorption and bioaccumulation processes. The influence of pH, Er(III) concentration, contact time and temperature on the biosorption capacity of Arthospira platensis was determined. The optimal conditions for Er(III) removal were defined as pH 3.0, time 15 min and temperature 20 °C, when 30 mg/g of Er(III) were removed. The kinetics of the process was better described by the pseudo-first-order model, while equilibrium fitted to the Freundlich model. In bioaccumulation experiments, the uptake capacity of biomass and Er(III) effect on biomass biochemical composition were assessed. It was shown that Er(III) in concentrations 10-30 mg/L did not affect the content of biomass, proteins, carbohydrate and photosynthetic pigments. Its toxicity was expressed by the reduction of the lipids content and growth of the level of malonic dialdehyde. Biomass accumulated 45-78% of Eu(III) present in the cultivation medium. Therefore, Arthospira platensis can be considered as a safe and efficient bioremediator of erbium contaminated environment.

Synthesis and antibacterial activity evaluation of N (7) position-modified balofloxacins

A series of small-molecule fluoroquinolones were synthesized, characterized by HRMS and NMR spectroscopy, and screened for their antibacterial activity against MRSA, P. aeruginosa, and E. coli as model G+/G− pathogens. Compounds 2-e, 3-e, and 4-e were more potent than the reference drug balofloxacin against MRSA and P. aeruginosa (MIC values of 0.0195 and 0.039 μg/ml for 2-e, 0.039 and 0.078 μg/ml for each of 3-e and 4-e, respectively). Analysis of the time-dependent antibacterial effect of compound 2-e toward MRSA showed that in the early logarithmic growth phase, bactericidal effects occurred, while in the late logarithmic growth phase, bacterial inhibition occurred because of concentration effects and possibly the development of drug resistance. Compound 2-e exhibited low toxicity toward normal mammalian cell lines 3T3 and L-02 and tumor cell lines A549, H520, BEL-7402, and MCF-7. The compound was not hemolytic. Atomic force microscopy (AFM) revealed that compound 2-e could effectively destroy the membrane and wall of MRSA cells, resulting in the outflow of the cellular contents. Docking studies indicated the good binding profile of these compounds toward DNA gyrase and topoisomerase IV. ADMET’s prediction showed that most of the synthesized compounds followed Lipinski’s “rule of five” and possessed good drug-like properties. Our data suggested that compound 2-e exhibited potent anti-MRSA activity and is worthy of further investigation.

A Novel Low-Cost Bio-Sorbent Prepared from Crisp Persimmon Peel by Low-Temperature Pyrolysis for Adsorption of Organic Dyes

In order to properly reuse food waste and remove various contaminants from wastewater, the development of green, sustainable and clean technologies has demonstrated potential in the efficient inhibition of secondary pollution to the environment. In this study, an economical and green method was used to prepare biochar from crisp persimmon peel (CPP) using flash-vacuum pyrolysis at different temperatures (200–700 °C; referred to as CPP200–CPP700). CPP200 has high polarity, low aromaticity and high oxygen-containing functional groups that exhibit superior MB adsorption capabilities. CPP200 that was prepared at a relatively low temperature of 200 °C exhibited a high adsorption capacity of 59.72 mg/g toward methylene blue (MB), which was relatively higher than that for alizarin yellow R (4.05 mg/g) and neutral red (39.08 mg/g), indicating that CPP200 possesses a higher adsorption selectivity for cationic dyes. Kinetics investigation revealed that the kinetic data of CPP200 for the adsorption of MB was better fitted by a linear pseudo-second-order model. Isothermal studies indicated that the linear Langmuir model was more suitable for describing the adsorption process. The adsorption thermodynamics illustrated that the adsorption of MB onto CPP200 was spontaneous and endothermic. EDS and IR analyses of CPP200 for both pre- and post-adsorption of MB showed that electrostatic interactions between oxygen-containing groups on biochar and target MB dominated the adsorption procedure, in addition to hydrogen bonding interactions. Reusability tests confirmed the excellent regeneration characteristics of CPP200, indicating that CPP200 may be used as a green, sustainable, highly efficient and recyclable adsorbent for the selective removal of cationic organic dyes.

Electrochemical Analysis of Sulfisoxazole Using Glassy Carbon Electrode (GCE) and MWCNTs/Rare Earth Oxide (CeO2 and Yb2O3) Modified-GCE Sensors

In this work, new electrochemical sensors based on the modification of glassy carbon electrode (GCE) with multiwalled carbon nanotubes (MWCNTs)-rare metal oxides (REMO) nanocomposites were fabricated by drop-to-drop method of MWCNTs-REMO dispersion in ethanol. REMO nanoparticles were synthesized by precipitation followed by hydrothermal treatment at 180 °C in absence and presence of TritonTM X-100 surfactant. Cyclic voltammetry (CV) analysis using MWCNTs-CeO2@GCE and MWCNTs-Yb2O3@GCE sensors were used for the analysis of sulfisoxazole (SFX) drug in water samples. The results of CV analysis showed that MWCNTs-REMO@GCE sensors have up to 40-fold higher sensitivity with CeO2 compared to the bare GCE sensor. The estimated values of the limit of detection (LoD) of this electrochemical sensing using MWCNTs-CeO2@GCE and MWCNTs-Yb2O3@GCE electrodes reached 0.4 and 0.7 μM SFX in phosphate buffer pH = 7, respectively. These findings indicate that MWCNTs-REMO@GCE electrodes are potential sensors for analysis of sulfonamide drugs in water and biological samples.

Synthesis and Application of Cobalt Oxide (Co3O4)-Impregnated Olive Stones Biochar for the Removal of Rifampicin and Tigecycline: Multivariate Controlled Performance

Cobalt oxide (Co₃O₄) nanoparticles supported on olive stone biochar (OSBC) was used as an efficient sorbent for rifampicin (RIFM) and tigecycline (TIGC) from wastewater. Thermal stabilities, morphologies, textures, and surface functionalities of two adsorbents; OSBC and Co-OSBC were compared. BET analysis indicated that Co-OSBC possesses a larger surface area (39.85 m²/g) and higher pore-volume compared to the pristine OSBC. FT-IR analysis showed the presence of critical functional groups on the surface of both adsorbents. SEM and EDX analyses showed the presence of both meso- and macropores and confirmed the presence of Co₃O₄ nanoparticles on the adsorbent surface. Batch adsorption studies were controlled using a two-level full-factorial design (2^k-FFD). Adsorption efficiency of Co-OSBC was evaluated in terms of the % removal (%R) and the sorption capacity (q_e, mg/g) as a function of four variables: pH, adsorbent dose (AD), drug concentration, and contact time (CT). A %R of 95.18% and 75.48% could be achieved for RIFM and TIGC, respectively. Equilibrium studies revealed that Langmuir model perfectly fit the adsorption of RIFM compared to Freundlich model for TIGC. Maximum adsorption capacity (q_max) for RIFM and TIGC was 61.10 and 25.94 mg/g, respectively. Adsorption kinetics of both drugs could be best represented using the pseudo-second order (PSO) model.

Application of Samarium- and Terbium-Sensitized Luminescence via a Multivariate-Based Approach for the Determination of Orbifloxacin

A lanthanide-based optical sensor has been developed for the sensitive and reliable spectrofluorometric determination of the fluoroquinolone antibiotic orbifloxacin (ORLX). Reaction of ORLX and two lanthanide metal ions, Sm(III) and Tb(III), in aqueous buffered solution produced highly fluorescent complexes. Plackett–Burman design (PBD) was used to explore the impact of four factors, pH, temperature (Temp), contact time (CT), and metal volume (MV), on the fluorescence intensity (FI) of the produced complexes. The obtained data showed that pH was the most significant variable. A blend of pH = 5.0, MV = 2.0 mL, T = 25°C, and CT = 10 min was used to achieve the maximum FI. FT-IR and Raman analyses were performed for the crystals of the as-prepared complexes. Obtained data showed shifting in most of the absorption bands, confirming the complexation of ORLX with both metal ions. Job’s method showed that the stoichiometry for the reaction of ORLX with Sm(III) and Tb(III) was 1 : 1. The proposed method was validated following the ICH guidelines. Injection formulation was analyzed successfully with the developed method with high recovery (99.42–100.91%). The detection and quantification limits were 0.987 and 3.289 ng/mL for the ORLX-Sm(III) complex and 1.020 and 3.399 ng/mL for the ORLX-Tb(III) complex, respectively.

Biochar for agronomy, animal farming, anaerobic digestion, composting, water treatment, soil remediation, construction, energy storage, and carbon sequestration: a review

In the context of climate change and the circular economy, biochar has recently found many applications in various sectors as a versatile and recycled material. Here, we review application of biochar-based for carbon sink, covering agronomy, animal farming, anaerobic digestion, composting, environmental remediation, construction, and energy storage. The ultimate storage reservoirs for biochar are soils, civil infrastructure, and landfills. Biochar-based fertilisers, which combine traditional fertilisers with biochar as a nutrient carrier, are promising in agronomy. The use of biochar as a feed additive for animals shows benefits in terms of animal growth, gut microbiota, reduced enteric methane production, egg yield, and endo-toxicant mitigation. Biochar enhances anaerobic digestion operations, primarily for biogas generation and upgrading, performance and sustainability, and the mitigation of inhibitory impurities. In composts, biochar controls the release of greenhouse gases and enhances microbial activity. Co-composted biochar improves soil properties and enhances crop productivity. Pristine and engineered biochar can also be employed for water and soil remediation to remove pollutants. In construction, biochar can be added to cement or asphalt, thus conferring structural and functional advantages. Incorporating biochar in biocomposites improves insulation, electromagnetic radiation protection and moisture control. Finally, synthesising biochar-based materials for energy storage applications requires additional functionalisation.