1
|
Jung YJ, Jang SH. Crack Detection of Reinforced Concrete Structure Using Smart Skin. NANOMATERIALS (BASEL, SWITZERLAND) 2024; 14:632. [PMID: 38607166 PMCID: PMC11013725 DOI: 10.3390/nano14070632] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Subscribe] [Scholar Register] [Received: 03/14/2024] [Revised: 04/01/2024] [Accepted: 04/03/2024] [Indexed: 04/13/2024]
Abstract
The availability of carbon nanotube (CNT)-based polymer composites allows the development of surface-attached self-sensing crack sensors for the structural health monitoring of reinforced concrete (RC) structures. These sensors are fabricated by integrating CNTs as conductive fillers into polymer matrices such as polyurethane (PU) and can be applied by coating on RC structures before the composite hardens. The principle of crack detection is based on the electrical change characteristics of the CNT-based polymer composites when subjected to a tensile load. In this study, the electrical conductivity and electro-mechanical/environmental characterization of smart skin fabricated with various CNT concentrations were investigated. This was performed to derive the tensile strain sensitivity of the smart skin according to different CNT contents and to verify their environmental impact. The optimal CNT concentration for the crack detection sensor was determined to be 5 wt% CNT. The smart skin was applied to an RC structure to validate its effectiveness as a crack detection sensor. It successfully detected and monitored crack formation and growth in the structure. During repeated cycles of crack width variations, the smart skin also demonstrated excellent reproducibility and electrical stability in response to the progressive occurrence of cracks, thereby reinforcing the reliability of the crack detection sensor. Overall, the presented results describe the crack detection characteristics of smart skin and demonstrate its potential as a structural health monitoring (SHM) sensor.
Collapse
Affiliation(s)
- Yu-Jin Jung
- Department of Smart City Engineering, Hanyang University ERICA, Ansan 15588, Republic of Korea;
| | - Sung-Hwan Jang
- Department of Smart City Engineering, Hanyang University ERICA, Ansan 15588, Republic of Korea;
- Department of Civil and Environmental Engineering, Hanyang University ERICA, Ansan 15588, Republic of Korea
| |
Collapse
|
2
|
Wu S, Li H, Futaba DN, Chen G, Chen C, Zhou K, Zhang Q, Li M, Ye Z, Xu M. Structural Design and Fabrication of Multifunctional Nanocarbon Materials for Extreme Environmental Applications. ADVANCED MATERIALS (DEERFIELD BEACH, FLA.) 2022; 34:e2201046. [PMID: 35560664 DOI: 10.1002/adma.202201046] [Citation(s) in RCA: 8] [Impact Index Per Article: 4.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Received: 01/31/2022] [Revised: 04/27/2022] [Indexed: 06/15/2023]
Abstract
Extreme environments represent numerous harsh environmental conditions, such as temperature, pressure, corrosion, and radiation. The tolerance of applications in extreme environments exemplifies significant challenges to both materials and their structures. Given the superior mechanical strength, electrical conductivity, thermal stability, and chemical stability of nanocarbon materials, such as carbon nanotubes (CNTs) and graphene, they are widely investigated as base materials for extreme environmental applications and have shown numerous breakthroughs in the fields of wide-temperature structural-material construction, low-temperature energy storage, underwater sensing, and electronics operated at high temperatures. Here, the critical aspects of structural design and fabrication of nanocarbon materials for extreme environments are reviewed, including a description of the underlying mechanism supporting the performance of nanocarbon materials against extreme environments, the principles of structural design of nanocarbon materials for the optimization of extreme environmental performances, and the fabrication processes developed for the realization of specific extreme environmental applications. Finally, perspectives on how CNTs and graphene can further contribute to the development of extreme environmental applications are presented.
Collapse
Affiliation(s)
- Sijia Wu
- School of Materials Science and Engineering, State Key Laboratory of Material Processing and Die and Mould Technology, Huazhong University of Science and Technology, Wuhan, 430074, China
| | - Huajian Li
- School of Materials Science and Engineering, State Key Laboratory of Material Processing and Die and Mould Technology, Huazhong University of Science and Technology, Wuhan, 430074, China
| | - Don N Futaba
- Nano Carbon Device Research Center, National Institute of Advanced Industrial Science and Technology (AIST), Tsukuba, 305-8565, Japan
| | - Guohai Chen
- Nano Carbon Device Research Center, National Institute of Advanced Industrial Science and Technology (AIST), Tsukuba, 305-8565, Japan
| | - Chen Chen
- School of Materials Science and Engineering, State Key Laboratory of Material Processing and Die and Mould Technology, Huazhong University of Science and Technology, Wuhan, 430074, China
| | - Kechen Zhou
- School of Materials Science and Engineering, State Key Laboratory of Material Processing and Die and Mould Technology, Huazhong University of Science and Technology, Wuhan, 430074, China
| | - Qifan Zhang
- School of Materials Science and Engineering, State Key Laboratory of Material Processing and Die and Mould Technology, Huazhong University of Science and Technology, Wuhan, 430074, China
| | - Miao Li
- School of Materials Science and Engineering, State Key Laboratory of Material Processing and Die and Mould Technology, Huazhong University of Science and Technology, Wuhan, 430074, China
| | - Zonglin Ye
- School of Materials Science and Engineering, State Key Laboratory of Material Processing and Die and Mould Technology, Huazhong University of Science and Technology, Wuhan, 430074, China
| | - Ming Xu
- School of Materials Science and Engineering, State Key Laboratory of Material Processing and Die and Mould Technology, Huazhong University of Science and Technology, Wuhan, 430074, China
| |
Collapse
|