Removal of Radioactive Iodine Using Silver/Iron Oxide Composite Nanoadsorbents

Impact of (nano ZnO/multi-wall CNTs) prepared by arc discharge method on the removal efficiency of stable iodine 127I and radioactive iodine 131I from water

Radioactive iodine isotopes especially 131I are used for diagnosis and treatment of different types of cancer diseases. Due to the leak of radioactive iodine into the patient's urine in turn, the wastewater would be contaminated, so it is worth preparing a novel adsorption green material to remove the radioactive iodine from wastewater efficiently. The removal of 127I and 131I contaminants from aqueous solution is a problem of interest. Therefore, this work presents a new study for removing the stable iodine 127I- and radioactive iodine 131I from aqueous solutions by using the novel nano adsorbent (Nano ZnO/MWCNTs) which is synthesized by the arc discharge method. It is an economic method for treating contaminated water from undesired dissolved iodine isotopes. The optimal conditions for maximum removal are (5 mg/100 ml) as optimum dose with shacking (200 rpm) for contact time of (60 min), at (25 °C) in an acidic medium of (pH = 5). After the adsorption process, the solution is filtrated and the residual iodide (127I-) is measured at a maximum UV wavelength absorbance of 225 nm. The maximum adsorption capacity is (15.25 mg/g); therefore the prepared nano adsorbent (Nano ZnO/MWCNTs) is suitable for treating polluted water from low iodide concentrations. The adsorption mechanism of 127I- on to the surface of (Nano ZnO/MWCNTs) is multilayer physical adsorption according to Freundlich isotherm model and obeys the Pseudo-first order kinetic model. According to Temkin isotherm model the adsorption is exothermic. The removal efficiency of Nano ZnO/MWCNTs for stable iodine (127I-) from aqueous solutions has reached 97.23%, 89.75%, and 64.78% in case of initial concentrations; 0.1843 ppm, 0.5014 ppm and 1.0331 ppm, respectively. For the prepared radio iodine (131I-) solution of radioactivity (20 µCi), the dose of nano adsorbent was (10 mg/100 ml) and the contact time was (60 min) at (pH = 5) with shacking (200 rpm) at (25 °C). The filtration process was done by using a syringe filter of a pore size (450 nm) after 2 days to equilibrate. The removal efficiency reached (34.16%) after the first cycle of treatment and the percentage of residual radio iodine was (65.86%). The removal efficiency reached (94.76%) after five cycles of treatment and the percentage of residual radio iodine was (5.24%). This last percentage was less than (42.15%) which produces due to the natural decay during 10 days.

Reusable cellulose-based biosorbents for efficient iodine adsorption by economic microcrystalline cellulose production from walnut shell

Sustainable management of walnut shell (WS) for the extraction of cellulose and preparation of cellulose-based biosorbents of iodine was carried out as a new approach to simultaneously solve the environmental challenge of agricultural solid waste and iodine-contaminated water. A rapid recyclable nitric acid treatment and NaOH-H2O2 alkaline-peroxide treatment of WS (33 % cellulose) extracted pure microcrystalline (Cac) and impure cellulose (Cal) with a 21.70 % and 47.37 % isolation yield, respectively. The techno-economic assessment of cellulose production showed a net profit of 9.02 $/kg for Cac, whereas it was estimated as negative for Cal. The simultaneous carbonization and magnetization of Cac at 550 °C resulted in an amorphous, magnetic cellulose-derived biochar (MB550Cac) with a BET specific surface area of 12.64 m2/g, decorated with scattered irregular Fe3O4 microparticles. The adsorption capacity of MB550Cac for iodine was 555.63 mg/g, which was lost only 17.45 % after six successful cycles of regeneration. Freundlich isotherm model sufficiently described the reversible iodine adsorption on the heterogenous surface. The adsorption kinetics followed the pseudo-second-order model. Further, the adsorption thermodynamics demonstrated spontaneous and favorable adsorption. These findings suggest the valorization of WS to commercially produce cellulose and MB550Cac as a sustainable, efficient biosorbent with a good application prospect in wastewater treatment.

Construction of a novel ursolic acid-based supramolecular gel for efficient removal of iodine from solution

Pentacyclic triterpenes is a natural amphipathic product which possess a rigid backbone and several polar functional groups such as hydroxyl, carbonyl and carboxyl groups. The amphipathic character makes it easy to realize self-assemble into complex nano structure and therefore attract extensive attention due to the simple synthetic processes and renewable raw materials. Hence, a novel Ursolic acid-based hydrogel was prepared successfully via a simple self-assembly of triterpenoid derivative in methanol by capture water molecule in air. The resulting hydrogel show a porous morphology and good elasticity including strong heat resistance. Based on the characteristic above, the hydrogel showed a good iodine adsorption capacity and can removal 75.0% of the iodine from cyclohexane solution and 66.3% from aqueous solution within 36 h. Data analysis indicate that all the iodine adsorption process are dominated by chemisorption and belongs to the multi-site adsorption on heterogenous surfaces. In addition, the obtained hydrogel also possesses a good recyclability which can maintain more than 82% of its capacity after 5 cycles. The simple preparation method and easily available raw materials endow it a great potential in future pollutant treatment.

Recent Advances in the Removal of Radioactive Iodine and Iodide from the Environment

Iodine (I2) in the form of iodide ions (I-) is an essential chemical element in the human body. Iodine is a nonmetal that belongs to the VIIA group (halogens) in the periodic table. Over the last couple of centuries, the exponential growth of human society triggered by industrialization coincided with the use of iodine in a wide variety of applications, including chemical and biological processes. However, through these processes, the excess amount of iodine eventually ends up contaminating soil, underground water, and freshwater sources, which results in adverse effects. It enters the food chain and interferes with biological processes with serious physiological consequences in all living organisms, including humans. Existing removal techniques utilize different materials such as metal-organic frameworks, layered double hydroxides, ion-exchange resins, silver, polymers, bismuth, carbon, soil, MXenes, and magnetic-based materials. From our literature survey, it was clear that absorption techniques are the most frequently experimented with. In this Review, we have summarized current advancements in the removal of iodine and iodide from human-made contaminated aqueous waste.

Viologen-functionalized magnetic material for the removal of Iodine and benzanthracene in an aqueous solution

The development of magnetically active adsorbents for effective iodine removal would be highly desirable to address environmental pollution and remediation. Herein, we demonstrated the synthesis of Vio@SiO₂@Fe₃O₄ as an adsorbent via surface functionalisation of electron-deficient bipyridium (viologen) units on the surface of magnetically active silica-coated magnetite (Fe₃O₄) core. This adsorbent was characterised thoroughly using various analytical techniques, such as field emission scanning electron microscopy (FESEM), thermal gravimetric analysis, Fourier transform infrared spectroscopy (FTIR), field emission transmission electron microscopy (FETEM), Brunauer-Emmett-Teller (BET) analysis and X-ray photon analysis (XPS). The removal of triiodide from the aqueous solution was monitored via the batch method. It revealed that the complete removal was achieved upon stirring for 70 min. The thermally stable and crystalline Vio@SiO₂@Fe₃O₄ displayed efficient removal capacity even in the presence of other competing ions and at different pHs. The adsorption kinetics data were analysed following the pseudo-first-order and pseudo-second-order models. Further, the isotherm experiment showed that the maximum uptake capacity of iodine is 1.38 g/g. It can be regenerated and reused over multiple cycles to capture iodine. Further, Vio@SiO₂@Fe₃O₄ displayed a good removal capacity toward toxic polyaromatic, Benzanthracene (BzA) pollutant with an uptake capacity of 2445 μg/g. This effective removal of toxic pollutants iodine/benzanthracene was attributed to the strong non-covalent electrostatic and π-π interaction with electron-deficient bipyridium units.

Nanostructured Materials and Advanced Processes for Application in Water Purification

Water pollution is a major environmental problem that has a significant impact on human and animal health and the ecosystem [...].

Facile Preparation of MCM-41/Ag2O Nanomaterials with High Iodide-Removal Efficiency

The elimination of iodide (I^-) from water is a tough subject due to its low adsorption tendency and high mobility. In this work, MCM-41/Ag₂O nanomaterials were prepared, characterized, and employed to adsorb I^- from water. The Ag₂O nanoparticles were dispersed homogeneously in the pores or at the surface of the MCM-41 support, and the Ag₂O nanoparticles in the pores had small particles sizes due to the confinement of the mesoporous channel. The prepared MCM-41/Ag₂O nanomaterials exhibited a higher specific surface area than previously reported Ag₂O-based composites. The adsorption of I^- by the nanomaterials was able to reach equilibrium at 180 min. The MCM-41/Ag₂O nanomaterials showed a better adsorption capacity per unit mass of Ag₂O than pure Ag₂O nanoparticles and previously reported Ag₂O-based composites prepared using other supports. Furthermore, the MCM-41/Ag₂O nanomaterials exhibited high selectivity for I^- in the presence of high concentrations of competitive anions, such as Cl^- or Br^-, and could function in a wide range of pH. The chemical reaction between Ag₂O and I^- and the surface adsorption were the main adsorption mechanisms. These results indicate that MCM-41/Ag₂O nanomaterials are a promising and efficient adsorbent material suitable for the removal of I^- for practical application.

Selective removal of radioactive iodine from water using reusable Fe@Pt adsorbents

Environmental damage from serious nuclear accidents should be urgently restored, which needs the removal of radioactive species. Radioactive iodine isotopes are particularly problematic for human health because they are released in large amounts and retain radioactivity for a substantial time. Herein, we prepare platinum-coated iron nanoparticles (Fe@Pt) as a highly selective and reusable adsorbent for iodine species, i.e., iodide (I^-), iodine (I₂), and methyl iodide (CH₃I). Fe@Pt selectively separates iodine species from seawater and groundwater with a removal efficiency ≥ 99.8%. The maximum adsorption capacity for the iodine atom of all three iodine species was determined to be 25 mg/g. The magnetic properties of Fe@Pt allow for the facile recovery and reuse of Fe@Pt, which remains stable with high efficiency (97.5%) over 100 uses without structural and functional degradation in liquid media. Practical application to the removal of radioactive ¹²⁹I and feasibility for scale-up using a 20 L system demonstrate that Fe@Pt can function as a reusable adsorbent for the selective removal of iodine species. This systematic procedure is a standard protocol for designing highly active adsorbents for the clean separation and removal of various chemical species dissolved in wastewater.

Interface assembly of specific recognition gripper wrapping on activated collagen fiber for synergistic capture effect of iodine

Efficient capture of radioactive iodine (¹²⁹I, ¹³¹I) is of great significance in spent fuel treatment. In this paper, a new adsorbent named Catechin@ACF was successfully prepared through interface assembly of specific recognition gripper with plant polyphenols (catechin) on activated collagen fiber (ACF), and the catechin membrane with specific grip on iodine was successfully constructed on the surface of ACF. The results showed that the adsorbent assembled catechin membrane was rich in aromatic rings, hydroxyl groups and imine adsorption sites, and possessed specific recognition and capture characteristics of iodine. Moreover, the as-prepared Catechin@ACF showed excellent capture capacity for iodine vapor and iodine in organic solution with the maximum capture capacity of 2122.68 mg/g and 258.29 mg/g, respectively. In iodine-cyclohexane solution, the adsorption process was in according with the Pseudo first order kinetic and Langmuir isothermal model. In addition, the specific recognition and capture mechanism analysis indicated that the aromatic rings, phenolic hydroxyl groups and imine groups in the catechin membrane were the specific and effective grippers for iodine, and finally iodine formed a stable conjugated system with the adsorbent in the form of I^- and I₃^-. Therefore, the as-prepared specific iodine capturer Catechin@ACF was expected to play a vital role in the capture of radioactive iodine in spent fuel off-gas because of its specific recognition, high capture capacity, large-scale preparation, and environment-friendly.

One-pot synthesis of sulfonic acid functionalized Zr-MOFs for rapid and specific removal of radioactive Ba2

Efficient decontamination of radioactive Ba2+ is of great significance to human health and environmental safety. Herein, an adsorbent based on the sulfonic acid functionalized Zr-MOF has been successfully developed, which could efficiently decontaminate radioactive Ba2+ with excellent selectivity, recyclability, a high adsorption capacity up to 60.8 mg g-1 as well as a short adsorption kinetic time of less than 5 min. This outstanding adsorption performance is attributed to the strong affinity between Ba2+ and high density -SO3H active sites in MOFs which were introduced by an in situ ligand modification strategy during the assembly of MOFs.