Cinnamomum tamala Leaf Extract Stabilized Zinc Oxide Nanoparticles: A Promising Photocatalyst for Methylene Blue Degradation

Highly Porous Polymer Beads Coated with Nanometer-Thick Metal Oxide Films for Photocatalytic Oxidation of Bisphenol A

Highly porous metal oxide-polymer nanocomposites are attracting considerable interest due to their unique structural and functional features. A porous polymer matrix brings properties such as high porosity and permeability, while the metal oxide phase adds functionality. For the metal oxide phase to perform its function, it must be fully accessible, and this is possible only at the pore surface, but functioning surfaces require controlled engineering, which remains a challenge. Here, highly porous nanocomposite beads based on thin metal oxide nanocoatings and polymerized high internal phase emulsions (polyHIPEs) are demonstrated. By leveraging the unique properties of polyHIPEs, i.e., a three-dimensional (3D) interconnected network of macropores, and high-precision of the atomic-layer-deposition technique (ALD), we were able to homogeneously coat the entire surface of the pores in polyHIPE beads with TiO2-, ZnO-, and Al2O3-based nanocoatings. Parameters such as nanocoating thickness, growth per cycle (GPC), and metal oxide (MO) composition were systematically controlled by varying the number of deposition cycles and dosing time under specific process conditions. The combination of polyHIPE structure and ALD technique proved advantageous, as MO-nanocoatings with thicknesses between 11 ± 3 and 40 ± 9 nm for TiO2 or 31 ± 6 and 74 ± 28 nm for ZnO and Al2O3, respectively, were successfully fabricated. It has been shown that the number of ALD cycles affects both the thickness and crystallinity of the MO nanocoatings. Finally, the potential of ALD-derived TiO2-polyHIPE beads in photocatalytic oxidation of an aqueous bisphenol A (BPA) solution was demonstrated. The beads exhibited about five times higher activity than nanocomposite beads prepared by the conventional (Pickering) method. Such ALD-derived polyHIPE nanocomposites could find wide application in nanotechnology, sensor development, or catalysis.

Bio-functionalized magnetic nanoparticles for cost-effective adsorption of U(vi): experimental and theoretical investigation

U(vi) removal using cost-effective (production cost: $14.03 per kg), biocompatible, and superparamagnetic Cinnamomum tamala (CT) leaf extract-coated magnetite nanoparticles (CT@MNPs or CT@Fe₃O₄ nanoparticles) from water resources was studied. From pH-dependent experiments, the maximum adsorption efficiency was found to be at pH 8. Isotherm and kinetic studies were performed and found to follow Langmuir isotherm and pseudo-second order kinetics, respectively. The maximum adsorption capacity of CT@MNPs was calculated to be 45.5 mg of U(vi) per g of nanoparticles (NPs). Recyclability studies suggest that over 94% sorption was retained even after four consecutive cycles. The sorption mechanism was explained by the point of the zero-charge experiment and the XPS measurement. Additionally, calculations using density functional theory (DFT) were carried out to support the experimental findings.

Green synthesis of zinc oxide nanoparticles using Brassica oleracea var. botrytis leaf extract: Photocatalytic, antimicrobial and larvicidal activity

Green synthesis of nanomaterials has emerged as an ecofriendly sustainable technology for the removal of dyes in the last few decades. Especially, plant leaf extracts have been considered as inexpensive and effective materials for the synthesis of nanoparticles. In this study, zinc oxide nanoparticles (ZnO NPs) were prepared using leaves extract of Brassica oleracea var. botrytis (BO) by co-precipitation and applied for photocatalytic/antibacterial activity. The synthesized BO-ZnO NPs was characterized by different instrumental techniques. The UV-vis Spectrum of the synthesized material showed maximum absorbance at a wavelength of 311 nm, which confirmed the formation of BO-ZnO NPs. The XRD pattern of BO-ZnO NPs represents a hexagonal wurtzite structure and the average size of particles was about 52 nm. FT-IR spectrum analysis confirms the presence of hydroxyl, carbonyl, carboxylic, and phenol groups. SEM images exhibited a flower like morphology and EDX spectrum confirming the presence of the elements Zn and O. Photo-catalytic activity of BO-ZnO NPs was tested against thiazine dye (methylene blue-MB) degradation under direct sunlight irradiation. Around 80% of the MB dye got degraded at pH 8 under 75 min of sunlight irradiation. Further, the study examined that the antimicrobial and larvicidal activity of BO-ZnO NPs obtained through green synthesis. The antimicrobial study results showed that the BO-ZnO NPs formed zones against bacterial pathogens. The results showed the formation of an inhibition zone against B. subtills (16 mm), S.aureus (13 mm), K. pneumonia (13 mm), and E. coli (9 mm) respectively at a concentration of 100 μg/mL of BO-ZnO NPs. The larvicidal activity of the BO-ZnO NPs was tested against the fourth instar of Culex quinquefasciatus mosquito larvae The LC₅₀ and LC₉₀ values estimated through the larvicidal activity of BO-ZnO NPs were 76.03, 190.03 ppm respectively. Hence the above findings propose the synthesized BO-ZnO NPs by the ecofriendly method can be used for various environmental and antipathogenic applications.

Nanostructured Materials and Advanced Processes for Application in Water Purification

Water pollution is a major environmental problem that has a significant impact on human and animal health and the ecosystem [...].

Resonance Coupling in Si@WS2Core-Ω Shell Nanostructure

Realizing strong laser-matter interaction in a heterostructure consisting of two-dimensional transition metal dichalcogenides (TMDCs) and an optical nanocavity is a potential strategy for novel photonic devices. In this paper, two core-Ω shell nanostructures, Si@WS₂ core-Ω shell nanostructure on glass/Si substrates, are briefly introduced. A strong laser-matter interaction occurred in the Si@WS₂ core-Ω shell nanostructure when it was excited by femtosecond (fs) laser in the near-infrared-1 region (NIR-1, 650 nm-950 nm), resulting in a resonance coupling between the electric dipole resonance (EDR) of the Si nanosphere (NS) and the exciton resonance of the WS₂ nanomembrane (NMB). The generation of resonance coupling regulates the resonant mode of the nanostructure to realize the multi-dimensional nonlinear optical response, which can be utilized in the fields of biological imaging and nanoscale light source.

Enhanced photocatalytic activity in ZnO nanoparticles developed using novel Lepidagathis ananthapuramensis leaf extract

The present study focuses on the green synthesis of zinc oxide nanoparticles (ZnO NPs) using a novel Lepidagathis ananthapuramensis (LA) leaf extract and a systematic study on the photocatalytic degradation of methylene blue (MB) dye. The structural, thermal, morphological, optical, and surface area analysis of prepared ZnO NPs were examined using X-ray diffraction (XRD), UV-visible spectroscopy, Raman spectroscopy, Fourier transform infrared spectroscopy (FT-IR), X-ray photoelectron spectroscopy (XPS), Brunauer-Emmett-Teller (BET) analysis, thermogravimetric analysis (TGA), field emission-scanning electron microscopy (FE-SEM), energy dispersive X-ray analysis (EDAX) and high-resolution transmission electron microscopy (HR-TEM). The LA stabilised ZnO NPs produced NPs with diverse morphologies, low band gap and cost-effective high yield of production. A systematic study has been carried out to determine the crystallinity and crystallite size of ZnO NPs based on the concentration of Zn(NO₃)₂ precursor, concentration of LA leaf extract, calcination temperature and calcination time. The crystallinity and crystallite size of ZnO NPs were evaluated based on the XRD technique. The photocatalytic activity of ZnO NPs was thoroughly investigated for the degradation of MB dye based on various physicochemical parameters such as reaction time, concentration of catalyst, concentration of precursors, concentration of LA extract, concentration of MB, calcination temperature and calcination time. These systematic photocatalytic studies followed green protocols and provided an excellent photocatalytic efficiency result of 96-98.5% towards the decomposition of MB. Hence, this material can work as a potential candidate for waste water treatment by also degrading other toxic dyes.

Bryophyllum pinnatum leaf extract mediated ZnO nanoparticles with prodigious potential for solar driven photocatalytic degradation of industrial contaminants

In an era of environment-friendly development plant extract-based biological techniques for synthesizing nanoparticles have gained a lot of attention over traditionally famous chemical and physical synthesis techniques. In the present study we have synthesized biogenic zinc oxide nanoparticles (BPLE-ZnO NPs) using Bryophyllum pinnatum leaf extract, compared its native properties and solar-driven photocatalytic activity with chemically prepared ZnO nanoparticles (Chem-ZnO NPs). In order to characterize and compare the Chem-ZnO and BPLE-ZnO, various techniques were used, including UV-visible spectroscopy, x-ray diffractrometry, photoluminescence spectroscopy, field emission scanning electron microscopy, electron dispersive x-ray spectroscopy, fourier transform infrared spectroscopy, and zeta potential analyzer. The results revealed the formation of hexagonal wurtzite ZnO, with no significant difference between the two methods; however, the use of Bryophyllum pinnatum leaf extract in ZnO NPs synthesis resulted in reduced size, presence of biomolecules on its surface and better monodispersity than purely chemical synthesis. Further, the BPLE-ZnO NPs showed better efficiency in the solar-driven photocatalytic degradation of methylene blue (MB) dye compared to Chem-ZnO NPs. Under solar exposure at a dose of 0.50 mg/mL BPLE-ZnO, resulted in 97.31% photodegradation with a rate constant of 0.06 min-1 of 20 mg/L MB solution within just 60 min which was 9.51% higher compared to the Chem-ZnO NPs. The BPLE-ZnO NPs were also employed to investigate their solar-driven photocatalytic performance for degrading the pharmaceutical (Metronidazole and Amoxycillin) and textile pollutants (Methyl orange dye) under sunlight. The results show that Bryophyllum pinnatum leaf extract-mediated ZnO NPs have an excellent potential in solar-based photocatalytic applications.

Effect of Calcination Temperature on Structural, Morphological and Optical Properties of Copper Oxide Nanostructures Derived from Garcinia mangostana L. Leaf Extract

Synthesis of copper oxide (CuO) nanostructures via biological approach has gained attention to reduce the harmful effects of chemical synthesis. The CuO nanostructures were synthesized through a green approach using the Garcinia mangostana L. leaf extract and copper (II) nitrate trihydrate as a precursor at varying calcination temperatures (200-600 °C). The effect of calcination temperatures on the structural, morphological and optical properties of CuO nanostructures was studied. The red shifting of the green-synthesized CuO nanoparticles' absorption peak was observed in UV-visible spectrum, and the optical energy bandgap was found to decrease from 3.41 eV to 3.19 eV as the calcination temperatures increased. The PL analysis shown that synthesized CuO NPs calcinated at 500 °C has the maximum charge carriers separation. A peak located at 504-536 cm^-1 was shown in FTIR spectrum that indicated the presence of a copper-oxygen vibration band and become sharper and more intense when increasing the calcination temperature. The XRD studies revealed that the CuO nanoparticles' crystalline size was found to increase from 12.78 nm to 28.17 nm, and dislocation density decreased from 61.26 × 10¹⁴ cm^-1 to 12.60 × 10¹⁴ cm^-1, while micro strain decreased from 3.40 × 10^-4 to 1.26 × 10^-4. From the XPS measurement, only CuO single phase without impurities was detected for the green-mediated NPs calcinated at 500 °C. The morphologies of CuO nanostructures were examined using FESEM and became more spherical in shape at elevated calcination temperature. More or less spherical nanostructure of green-mediated CuO calcinated at 500 °C were also observed using TEM. The purity of the green-synthesized CuO nanoparticles was evaluated by EDX analysis, and results showed that increasing calcination temperature increases the purity of CuO nanoparticles.

Synthesis of Silver, Gold, and Platinum Doped Zinc Oxide Nanoparticles by Pulsed Laser Ablation in Water

In this paper, we propose a simple two-step method for the synthesis of Ag, Au, and Pt-doped ZnO nanoparticles. The method is based on the fabrication of targets using the pulsed laser deposition (PLD) technique where thin layers of metals (Ag, Pt, Au) have been deposited on a metal-oxide bulk substrate (ZnO). Such formed structures were used as a target for the production of doped nanoparticles (ZnO: Ag, ZnO: Au, and ZnO: Pt) by laser ablation in water. The influence of Ag, Au, and Pt doping on the optical properties, structure and composition, sizing, and morphology was studied using UV-Visible (UV-Vis) and photoluminescence (PL) spectroscopies, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), and transmission electron microscopy (TEM), respectively. The band-gap energy decreased to 3.06, 3.08, and 3.15 for silver, gold, and platinum-doped ZnO compared to the pure ZnO (3.2 eV). PL spectra showed a decrease in the recombination rate of the electrons and holes in the case of doped ZnO. SEM, TEM, and AFM images showed spherical-shaped nanoparticles with a relatively smooth surface. The XRD patterns confirm that Ag, Au, and Pt were well incorporated inside the ZnO lattice and maintained a hexagonal wurtzite structure. This work could provide a new way for synthesizing various doped materials.

Green Synthesis and Antibacterial Activity of Ag/Fe2O3 Nanocomposite Using Buddleja lindleyana Extract

In the study reported in this manuscript, silver/iron oxide nanocomposites (Ag/Fe₂O₃) were phytosynthesized using the extract of Buddleja lindleyana via a green, economical and eco-friendly strategy. The biosynthesized Ag/Fe₂O₃ nanocomposites were characterized using UV-Vis spectrophotometry, FTIR, XRD, TEM, DLS and SEM-EDX analyses. The particulates showed a triangular and spherical morphology having sizes between 25 and 174 nm. FTIR studies on the nanoparticles showed functional groups corresponding to organic metabolites, which reduce and stabilize the Ag/Fe₂O₃ nanocomposite. The antimicrobial efficacy of the phytosynthesized Ag/Fe₂O₃ against bacterial pathogens was assessed. In addition, Ag/Fe₂O₃ exhibited broad spectrum activities against B. subtilis, S. aureus, E. coli, and P. aeruginosa with inhibition zones of 23.4 ± 0.75, 22.3 ± 0.57, 20.8 ± 1.6, and 19.5 ± 0.5 mm, respectively. The Ag/Fe₂O₃ composites obtained showed promising antibacterial action against human bacterial pathogens (S. aureus, E. coli, B. subtilis and P. aeruginosa), making them candidates for medical applications.

Enhancement of Methylene Blue Photodegradation Rate Using Laser Synthesized Ag-Doped ZnO Nanoparticles

In this work, Ag-doped ZnO nanoparticles are obtained via pulsed laser ablation of the Ag-coated ZnO target in water. The ratio of Ag dopant in ZnO nanoparticles strongly depends on the thickness of the Ag layer at the ZnO target. Synthesized nanoparticles were characterized by XRD, XPS, SEM, EDS, ICP-OES, and UV–VIS spectrophotometry to obtain their crystal structure, elemental composition, morphology and size distribution, mass concentration, and optical properties, respectively. The photocatalytic studies showed photodegradation of methylene blue (MB) under UV irradiation. Different ratios of Ag dopant in ZnO nanoparticles influence the photodegradation rate. The ZnO nanoparticles doped with 0.32% silver show the most efficient photodegradation rate, with the chemical reaction constant of 0.0233 min⁻¹. It exhibits an almost twice as large photodegradation rate compared to pure ZnO nanoparticles, showing the doping effect on the photocatalytic activity.

Photocatalytic Dye Degradation and Bio-Insights of Honey-Produced α-Fe2O3 Nanoparticles

Iron oxide nanoparticles are produced using simple auto combustion methods with honey as a metal-stabilizing and -reducing agent. Herein, α-Fe2O3 nanoparticles are produced using an iron nitrate precursor. These prepared samples are analyzed by an X-ray diffractometer (XRD), FTIR spectroscopy, UV-DRS, and a field-emission scanning electron microscope (FESEM) combined with energy-dispersive spectroscopy and a vibrating sample magnetometer (VSM). The XRD results confirm a rhombohedral structure with an R3c¯ space group single-phase formation of α-Fe2O3 in all samples. FESEM images reveal the different morphologies for the entire three samples. TEM analysis exhibits spherical shapes and their distribution on the surfaces. XPS spectroscopy confirms the Fe-2p and O-1s state and their valency. The VSM study shows strong ferromagnetic behavior. The prepared α-Fe2O3 nanoparticles exhibit exceptional charge carriers and radical production. The prepared sample retains excellent photocatalytic, antifungal and antibacterial activity.

Designing Z-scheme AgIO4 nanorod embedded with Bi2S3 nanoflakes for expeditious visible light photodegradation of congo red and rhodamine B

The present study describes the enhanced photodegradation of organic pollutant dyes, congo red (CR) and rhodamine B (RhB) dyes under visible light irradiation. AgIO₄ nanorods decorated on Bi₂S₃ nanoflakes in various proportions were synthesized via sono-chemical route wherein the deposition of varying amounts of AgIO₄ on Bi₂S₃ plays a pivotal role in improving the photodegradation ability. The characterization of the as-synthesized nanohybrids was assessed by XRD, UV-vis DRS, PL, EIS, ESR, FT-IR, XPS, HR-TEM, FE-SEM, N₂ adsorption and desorption techniques. The effect of initial CR and RhB dye concentration, reaction pH and usage of nanohybrid concentration were investigated where 30%-AgIO₄/Bi₂S₃ exhibited excellent visible light photodegradation of 95.58% for CR and 96.11% for RhB dyes at 140 min and 100 min respectively. The superoxide (•O^2-) and hydroxyl radicals (•OH) played predominant role in the photodegradation of CR and RhB which is experimentally confirmed by radical trapping experiments. Also, the photocatalysts exhibited good photo stability and excellent reusability. The TOC analysis confirmed the complete mineralization of CR and RhB dyes by the nanohybrid and the formation of possible intermediate and degradation pathway was delineated based on GC/MS analysis. The outstanding photodegradation performance were ascribed to the Z-scheme charge transfer path, which effectively promotes the separation and transfer of e^-/h⁺ pairs, resulting in a strong redox activity of the accumulated charge to decompose organic dyes during the degradation reaction. The study suggested that the nanohybrid can be utilized for the removal of organic pollutants from the contaminated water bodies.

Sustainable Green Nanotechnologies for Innovative Purifications of Water: Synthesis of the Nanoparticles from Renewable Sources

Polluting the natural water resources is a serious global issue, which is confirmed by the fact that today at least 2 billion people consume water from contaminated sources. The conventional wastewater treatment methods cannot effectively remove the persistent pollutants (e.g., drugs, organic dyes, pesticides) from the aqueous environment. Heterogeneous photocatalysis is a promising and sustainable alternative for water remediation. It is based on the interaction between light irradiation and the semiconductors (e.g., TiO₂, ZnO) as photocatalysts, but these compounds, unfortunately, have some disadvantages. Hence, great attention has been paid to the nanotechnology as a possible way of improvement. Nanomaterials have extraordinary properties; however, their conventional synthesis is often difficult and requires a significant amount of dangerous chemicals. This concise topical review gives recent updates and trends in development of sustainable and green pathways in the synthesis of nanomaterials, as well as in their application for water remediation. In our review we put emphasis on the eco-friendly, mostly plant extract-based materials. The importance of this topic, including this study as well, is proved by the growing number of publications since 2018. Due to the current serious environmental issues (e.g., global warming, shortage of pure and quality water), it is necessary for the traditional TiO₂ and ZnO semiconductors to be replaced with the harmless, non-toxic, and more powerful nanocomposites as photocatalysts. Not only because of their higher efficiency as compared to the bulk semiconductors, but also because of the presence of biomolecules that can add up to the pollutant removal efficiency, which has been already confirmed in many researches. However, despite the fact that the application of heterogeneous photocatalysis together with green nanotechnology is absolutely the future in water purification, there are some challenges which have to be overcome. The exact effects of the biomolecules obtained from plants in the synthesis of nanoparticles, as well as in the photocatalytic processes, are not exactly known and require further investigation. Furthermore, heterogeneous photocatalysis is a well-known and commonly examined process; however, its practical use outside the laboratory is expensive and difficult. Thus, it has to be simplified and improved in order to be available for everyone. The aim of our review is to suggest and prove that using these bio-inspired compounds it is possible to reduce human footprint in the nature.