Characteristic Aspects of Uranium(VI) Adsorption Utilizing Nano-Silica/Chitosan from Wastewater Solution

Uranium adsorption efficiency of diglycolamic acid functionalized graphitic carbon nitride adsorbent: Kinetic, isotherm, and thermodynamic studies

This study proposes the use of diglycolamic acid-functionalized graphitic carbon nitride (HDGA-gCN) as an adsorbent for uranium removal. Our experiments showed that at pH 6.0, HDGA-gCN had a high adsorption capacity of 263.2 mg g-1 and achieved equilibrium in 30 min. The adsorption isotherm was well-fitted by the Langmuir model, and the adsorption kinetics followed a pseudo-second-order equation. U(VI) adsorption on HDGA-gCN is due to electrostatic interactions between the amine, diglycolamic acid, and uranium species. The thermodynamic parameters indicate that adsorption is spontaneous and exothermic. The loaded U(VI) can be desorbed using 0.1 M Na2CO3, and HDGA-gCN exhibited an exceptional adsorption percentage for U(VI) compared to other coexisting ions. HDGA-gCN had faster kinetics, adsorption capacity, and reusability, making it suitable for U(VI) remediation.

A Phosphorylated Dendrimer-Supported Biomass-Derived Magnetic Nanoparticle Adsorbent for Efficient Uranium Removal

A novel biomass-based magnetic nanoparticle (Fe3O4-P-CMC/PAMAM) was synthesized by crosslinking carboxymethyl chitosan (CMC) and poly(amidoamine) (PAMAM), followed by phosphorylation with the incorporation of magnetic ferric oxide nanoparticles. The characterization results verified the successful functionalization and structural integrity of the adsorbents with a surface area of ca. 43 m2/g. Batch adsorption experiments revealed that the adsorbent exhibited a maximum adsorption capacity of 1513.47 mg·g-1 for U(VI) at pH 5.5 and 298.15 K, with Fe3O4-P-CMC/G1.5-2 showing the highest affinity among the series. The adsorption kinetics adhered to a pseudo-second-order model (R2 = 0.99, qe,exp = 463.81 mg·g-1, k2 = 2.15×10-2 g·mg-1·min-1), indicating a chemically driven process. Thermodynamic analysis suggested that the adsorption was endothermic and spontaneous (ΔH° = 14.71 kJ·mol-1, ΔG° = -50.63 kJ·mol-1, 298. 15 K), with increasing adsorption capacity at higher temperatures. The adsorbent demonstrated significant selectivity for U(VI) in the presence of competing cations, with Fe3O4-P-CMC/G1.5-2 showing a high selectivity coefficient. The performed desorption and reusability tests indicated that the adsorbent could be effectively regenerated using 1M HCl, maintaining its adsorption capacity after five cycles. XPS analysis highlighted the role of phosphonate and amino groups in the complexation with uranyl ions, and validated the existence of bimodal U4f peaks at 380.1 eV and 390.1 eV belonging to U 4f7/2 and U 4f5/2. The results of this study underscore the promise of the developed adsorbent as an effective and selective material for the treatment of uranium-contaminated wastewater.

Anti-inflammatory and anti-oxidative electrospun nanofiber membrane promotes diabetic wound healing via macrophage modulation

BACKGROUND

In the inflammatory milieu of diabetic chronic wounds, macrophages undergo substantial metabolic reprogramming and play a pivotal role in orchestrating immune responses. Itaconic acid, primarily synthesized by inflammatory macrophages as a byproduct in the tricarboxylic acid cycle, has recently gained increasing attention as an immunomodulator. This study aims to assess the immunomodulatory capacity of an itaconic acid derivative, 4-Octyl itaconate (OI), which was covalently conjugated to electrospun nanofibers and investigated through in vitro studies and a full-thickness wound model of diabetic mice.

RESULTS

OI was feasibly conjugated onto chitosan (CS), which was then grafted to electrospun polycaprolactone/gelatin (PG) nanofibers to obtain P/G-CS-OI membranes. The P/G-CS-OI membrane exhibited good mechanical strength, compliance, and biocompatibility. In addition, the sustained OI release endowed the nanofiber membrane with great antioxidative and anti-inflammatory activities as revealed in in vitro and in vivo studies. Specifically, the P/G-CS-OI membrane activated nuclear factor-erythroid-2-related factor 2 (NRF2) by alkylating Kelch-like ECH-associated protein 1 (KEAP1). This antioxidative response modulates macrophage polarization, leading to mitigated inflammatory responses, enhanced angiogenesis, and recovered re-epithelization, finally contributing to improved healing of mouse diabetic wounds.

CONCLUSIONS

The P/G-CS-OI nanofiber membrane shows good capacity in macrophage modulation and might be promising for diabetic chronic wound treatment.

Functionalized hydrogen-bonded organic superstructures via molecular self-assembly for enhanced uranium extraction

Effective uranium extraction from water is essential for the development of nuclear power industry and the protection of human health and environment. Nevertheless, it still remains challenging to realize efficient and cost-effective uranium extraction. Herein, a fast and simple method for the direct fabrication of novel functionalized hydrogen-bonded organic superstructures via molecular self-assembly is reported. The as-constructed flower-like superstructures (MCP-5) can allow the exposure of adsorption sites and facilitate the transport of uranyl ions, while synergism between amino and phosphate groups can realize selective uranium extraction. Consequently, MCP-5 possesses excellent uranium adsorption ability with a high saturated adsorption capacity of 950.52 mg g-1, high utilization rate of adsorption sites and adsorption equilibrium time of simply 5 min in uranium-spiked aqueous solution. Furthermore, MCP-5 offers selective uranium adsorption over a broad range of metal ions. The facile synthesis and low-cost raw materials make it have promising potential for uranium capture. Simultaneously, this study opens a design avenue of functionalized hydrogen-bonded organic material for efficient uranium extraction.

Selective Separation of Zr(IV) from Simulated High-Level Liquid Waste by Mesoporous Silica

The efficient separation of Zr(IV) ions from strong acidic and radioactive solutions is a significant challenge, especially in the context of the aqueous reprocessing of nuclear fuels. The complexity of such solutions, which are often characterized by high acidity and the presence of radioactive elements, poses formidable challenges for separation processes. Herein, several mesoporous silicas (HMS, MCM-41, KIT-6, and SiO2-70 Å) with excellent acid and radiation resistance properties were employed as sorbents to remove Zr(IV) ions from simulated high-level liquid waste. The batch experiments were designed to investigate the influence of adsorption time, HNO3 concentration, initial Zr(IV) concentration, adsorbent dosage, and temperature on the adsorption behavior of Zr(IV). The results indicate that the adsorption equilibrium time of mesoporous silica materials was approximately 8 h, and all the adsorption processes followed the pseudo-second-order kinetics equation. The isotherms of Zr(IV) adsorption by KIT-6 exhibited good agreement with the Langmuir model, while the Freundlich model could be utilized to fit the adsorption on HMS, MCM-41, and SiO2-70 Å. The adsorption capacity of MCM-41 for Zr(IV) in 3 mol/L HNO3 was 54.91 mg/g, which is three times the adsorption capacity reported for commercial silica gel (17.91 mg/g). The thermodynamic parameters indicate that the adsorption processes for zirconium are endothermic reactions. Furthermore, the mesoporous silicas exhibited a pronounced selectivity in the adsorption of Zr(IV) within a simulated high-level liquid waste containing 10 co-existing cations (3 mol/L HNO3). This suggests that mesoporous silicas have great potential for Zr(IV) removal in actual radioactive liquids with high acidity during spent fuel reprocessing.

Physicochemical investigation of mercury sorption on mesoporous thioacetamide/chitosan from wastewater

Mercury is a toxic environmental element, so it was necessary to prepare a new, highly efficient, cheap sorbent to remove it. A mesoporous thioacetamide/chitosan (MTA/CS) was manufactured via a simplistic strategy; the chitin deacetylation to gain chitosan (CS) and the addition of thioacetamide. The as-prepared MTA/CS was characterized using X-ray diffraction, EDX, SEM, FTIR, and BET surface analysis. According to the findings, the MTA/CS was effectively synthesized. The removal behaviors of Hg2+ onto MTA/CS composite were inspected, which suggested that the MTA/CS composite exhibited great sorption properties for Hg2+ in liquid solutions. The maximal Hg2+ sorption capacity was 195 mg/g. The effects of temperature, Hg2+ concentration, contacting time, and MTA/CS concentration on sorption were analyzed. The 2nd-order model and Langmuir isotherm were suitable for the physicochemical adsorption processes. Thermodynamic analysis showed that the Hg2+ adsorption process onto the MTA/CS composite is exothermic and occurred spontaneously. The desorption condition of Hg2+ from its loaded MTA/CS was also gained. Likewise, the MTA/CS sorbent was undoubtedly regenerated by 0.8 M NaNO3 80 min contacting and 1:50 S:L ratio. The versatility and durability of MTA/CS sorbent were investigated via nine sorption-extraction cycles. The optimum parameters were applied to wastewater. Based on the result, the as-prepared MTA/CS might be a potential sorbent for removing Hg2+ from liquid solutions.

Recovery of W(VI) from Wolframite Ore Using New Synthetic Schiff Base Derivative

A new synthetic material, namely, (3-(((4-((5-(((S)-hydroxyhydrophosphoryl)oxy)-2-nitrobenzylidene) amino) phenyl) imino) methyl)-4-nitrophenyl hydrogen (R)-phosphonate)), was subjected to a quaternary ammonium salt and named (HNAP/QA). Several characterizations, such as FTIR spectrometry, ¹H-NMR analysis, ¹³C-NMR analysis, ³¹P-NMR Analysis, TGA analysis, and GC-MS analysis, were performed to ensure its felicitous preparation. HNAP/QA is capable of the selective adsorption of W(VI) ions from its solutions and from its rock leachate. The optimum factors controlling the adsorption of W(VI) ions on the new adsorbent were studied in detail. Furthermore, kinetics and thermodynamics were studied. The adsorption reaction fits the Langmuir model. The sorption process of the W(VI) ions is spontaneous due to the negative value of ∆G° calculated for all temperatures, while the positive value of ∆H° proves that the adsorption of the W(VI) ions adsorption on HNAP/QA is endothermic. The positive value of ∆S° suggests that the adsorption occurs randomly. Ultimately, the recovery of W(IV) from wolframite ore was conducted successfully.

Chitosan-Bead-Encapsulated Polystyrene Sulfonate for Adsorption of Methylene Blue and Regeneration Studies: Batch and Continuous Approaches

Textile industrialization causes water pollution due to the discharge of industrial effluents into the environment. To reduce the impact of industrial effluent, it must be treated in wastewater treatment plants before discharge into rivers. Among all wastewater treatment approaches, the adsorption process is one method to remove pollutants from wastewater, but it has some limitations in term of reusability and ionic selective adsorption properties. In this study, we prepared cationic poly (styrene sulfonate) (PSS)-incorporated anionic chitosan beads synthesized using the oil-water emulsion coagulation method. The produced beads were characterized using FESEM and FTIR analysis. In batch adsorption studies, the PSS-incorporated chitosan beads exhibited monolayer adsorption processes, that is, exothermic processes that occur spontaneously at low temperatures, which were analyzed based on the adsorption isotherms, adsorption kinetics, and thermodynamics model fittings. The presence of PSS enables cationic methylene blue dye to adsorb to the anionic chitosan structure via electrostatic interaction between the sulfonic group and the dye molecule. The maximum adsorption capacity of PSS-incorporated chitosan beads achieved 42.21 mg/g, as calculated from the Langmuir adsorption isotherm. Finally, the PSS-incorporated chitosan beads demonstrated good regeneration with different types of reagents, especially using sodium hydroxide as a regeneration reagent. With the use of sodium hydroxide regeneration of this adsorbent material, a continuous adsorption setup also demonstrated that PSS-incorporated chitosan beads can be reused for methylene blue adsorption for up to three cycle processes.