Microemulsions of Nonionic Surfactant with Water and Various Homologous Esters: Preparation, Phase Transitions, Physical Property Measurements, and Application for Extraction of Tricyclic Antidepressant Drugs from Aqueous Media

Electrical Conductivity as an Informative Factor of the Properties of Liposomal Systems with Naproxen Sodium for Transdermal Application

Liposomal preparations play an important role as formulations for transdermal drug delivery; however, the electrical conductivity of these systems is sparingly evaluated. The aim of the study was to outline the range of the values of electrical conductivity values that may be recorded in the future pharmaceutical systems in the context of their viscosity. The electrical conductivity, measured by a conductivity probe of k = 1.0 cm-1, and the dynamic viscosity of liposomal and non-liposomal systems with naproxen sodium, embedded into a methylcellulose hydrophilic gel (0.25%), were compared with data from preparations without naproxen sodium in a range reflecting the naproxen sodium concentrations 0.1·10-2-9.5·10-2 mol/L. The specific conductivity covered a 1.5 μS·cm-1-5616.0 μS·cm-1 range, whereas the viscosity ranged from 0.9 to 9.4 mPa·s. The naproxen sodium highly influenced the electrical conductivity, whereas the dynamic viscosity was a moderate factor. The observed phenomena may be ascribed to the high mobility of sodium ions recruited from naproxen sodium and the relatively low concentrations of applied methylcellulose. The assembly of lecithin in liposomes may have lowered the specific conductivity of the systems with naproxen sodium. These measurements will be further developed for implementation as simple assays of the concentrations of active pharmaceutical ingredient in release experiments of preparations proposed for dermatological applications.

Strategies to Improve the Transdermal Delivery of Poorly Water-Soluble Non-Steroidal Anti-Inflammatory Drugs

The transdermal delivery of non-steroidal anti-inflammatory drugs (NSAIDs) has the potential to overcome some of the major disadvantages relating to oral NSAID usage, such as gastrointestinal adverse events and compliance. However, the poor solubility of many of the newer NSAIDs creates challenges in incorporating the drugs into formulations suitable for application to skin and may limit transdermal permeation, particularly if the goal is therapeutic systemic drug concentrations. This review is an overview of the various strategies used to increase the solubility of poorly soluble NSAIDs and enhance their permeation through skin, such as the modification of the vehicle, the modification of or bypassing the barrier function of the skin, and using advanced nano-sized formulations. Furthermore, the simple yet highly versatile microemulsion system has been found to be a cost-effective and highly successful technology to deliver poorly water-soluble NSAIDs.

Development of Visible Spectrophotometric Methods for the Determination of Tricyclic Antidepressants Based on Formation of Molecular Complexes with p-Benzoquinones

Tricyclic antidepressants are commonly employed in the management of major depressive disorders. The present work describes two visible (VIS) spectrophotometric techniques that utilize the formation of charge transfer complexes between four antidepressant compounds, namely, amitriptyline hydrochloride (AMI), imipramine hydrochloride (IMI), clomipramine hydrochloride (CLO), and trimipramine maleate (TRI) acting as electron donors and two p-benzoquinones, namely, p-chloranilic acid (pCA) and 2,3-dichloro-5,6-dicyano-1,4-benzoquinone (DDQ), serving as electron acceptors. The stoichiometry of the compounds produced exhibited a consistent 1:1 ratio in all instances, as established by Job's method. Molar absorptivities, equilibrium association constants, and several other spectroscopic properties were determined for all complexes. The developed spectrophotometric techniques were validated intra-laboratory and successfully applied for quantitative assessment of the four antidepressant active ingredients in several commercial pharmaceutical formulations. The methods are relatively simple, fast, and use readily available laboratory instrumentation, making them easily applicable by most quality control laboratories worldwide.

Antibacterial Activity of Zinc Oxide Nanoparticles Loaded with Essential Oils

One major problem with the overuse of antibiotics is that the microorganisms acquire resistance; thus the dose must be increased unsustainably. To overcome this problem, researchers from around the world are actively investigating new types of antimicrobials. Zinc oxide (ZnO) nanoparticles (NPs) have been proven to exhibit strong antimicrobial effects; moreover, the Food and Drugs Administration (FDA) considers ZnO as GRAS (generally recognized as safe). Many essential oils have antimicrobial activity and their components do not generate resistance over time. One of the drawbacks is the high volatility of some components, which diminishes the antimicrobial action as they are eliminated. The combination of ZnO NPs and essential oils can synergistically produce a stronger antimicrobial effect, and some of the volatile compounds can be retained on the nanoparticles' surface, ensuring a better-lasting antimicrobial effect. The samples were characterized with X-ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), ultraviolet-visible spectroscopy (UV-Vis), and thermal analysis (TG-DSC) coupled with analysis of evolved gases using FTIR. The ZnO NPs, with a size of ~35 nm, exhibited a loading between 1.44% and 15.62%-the lower values were specific for limonene-containing oils (e.g., orange, grapefruit, bergamot, or limette), while high values were obtained from cinnamon, minzol, thyme, citronella, and lavender oils-highlighting differences among non-polar terpenes and alcohol or aldehyde derivatives. The antibacterial assay indicated the existence of a synergic action among components and a high dependency on the percentage of loaded oil. Loaded nanoparticles offer immense potential for the development of materials with specific applications, such as wound dressings or food packaging. These nanoparticles can be utilized in scenarios where burst delivery is desired or when prolonged antibacterial activity is sought.