Sulfonated Poly(Arylene Ether Sulfone) and Perfluorosulfonic Acid Composite Membranes Containing Perfluoropolyether Grafted Graphene Oxide for Polymer Electrolyte Membrane Fuel Cell Applications

Facile Preparation of a Transparent and Rollable Omniphobic Coating with Exceptional Hardness and Wear Resistance

The encapsulating film for the touchscreen of a foldable smartphone consists of a flexible polymer layer covered by a hard coating and an antismudge coating, and the two coating layers are currently deposited via separate steps. This paper reports the preparation of a bilayer bifunctional coating via the deposition of a single polymer mixture. The base material for the coating is a ladder-like polysilsesquioxane (LASQ) that is derived from the sol-gel chemistry of 2-(3,4-epoxycyclohexyl)ethyltrimethoxysilane. Reacting a limiting amount of the liquid antismudge agent FP-COOH, which is a perfluorinated poly(propylene oxide) bearing a terminal carboxyl group, with LASQ yields m-LASQ-FP, a mixture of unreacted LASQ, and a graft copolymer LASQ-FP. m-LASQ-FP at a fluorine mass fraction of 6.0% is photocured to yield a coating with a surface energy of 12.3 ± 1.5 mJ/m². At a thickness of 40 μm, the coating has at 500 nm a transmittance of >99% measured against its glass substrate, a remarkable nanoindentation hardness H value of 1.4 GPa, and a pencil hardness of > 9H. After being abraded for 300 strokes under a pressure of 26 kPa with steel wool, the coating exhibits no noticeable degradation in its ink contraction properties. At a thickness of 10 μm on a poly(ethylene terephthalate) film, the coating can undergo inward (on the inner surface of the bend) and outward bending to radii <1 and <2 mm, respectively, without cracking. Aside from being a superb candidate as a protective antismudge coating for foldable smartphones, this marvelous material should also have many other applications.

Novel Polymeric Composite TPPS/s-PEEK Membranes for Low Relative Humidity PEFC

Composite membranes based on different wt percentages of meso-tetrakis-(4-sulfonatophenyl)porphyrin (TPPS) embedded in a medium sulfonation degree (50%) sulfonated poly(etheretherketone) (s-PEEK) were investigated. The successful introduction of porphyrin into the membranes and the characterization of its different species into the membrane ionic domains were carried out by spectroscopic techniques. Moreover, the effect of TPPS arrangement was investigated in terms of water retention, proton conductivity and fuel cell performance at low relative humidity (RH). It was found that the introduction of this porphyrin induces a variation of the chemical-physical parameters, such as ion exchange capacity (IEC), water up-take (Wup %) λ and proton concentration ([H+]), attributable to the interactions that occur between the sulfonic groups of the polymer and the nitrogen sites of TPPS. The TPPS, in its J-aggregated form, actively participates in the proton conduction mechanism, also maintaining the adequate water content in more drastic conditions (80 °C and 50% RH). A maximum power density value of 462 mW cm-2 was obtained for the s-PEEK membrane, with a 0.77 wt % content of TPPS. This evidence suggests that the presence of J-aggregates in the proton conduction channels maintains a good hydration, even if a drastic reduction of the RH of the reactant gases occurs, preventing the membrane from a dry-out effect.

Practical use of polymer brushes in sustainable energy applications: interfacial nanoarchitectonics for high-efficiency devices

The discovery and development of novel approaches, materials and manufacturing processes in the field of energy are compelling increasing recognition as a major challenge for contemporary societies. The performance and lifetime of energy devices are critically dependent on nanoscale interfacial phenomena. From the viewpoint of materials design, the improvement of current technologies inevitably relies on gaining control over the complex interface between dissimilar materials. In this sense, interfacial nanoarchitectonics with polymer brushes has seen growing interest due to its potential to overcome many of the limitations of energy storage and conversion devices. Polymer brushes offer a broad variety of resources to manipulate interfacial properties and gain molecular control over the synergistic combination of materials. Many recent examples show that the rational integration of polymer brushes in hybrid nanoarchitectures greatly improves the performance of energy devices in terms of power density, lifetime and stability. Seen in this light, polymer brushes provide a new perspective from which to consider the development of hybrid materials and devices with improved functionalities. The aim of this review is therefore to focus on what polymer brush-based solutions can offer and to show how the practical use of surface-grafted polymer layers can improve the performance and efficiency of fuel cells, lithium-ion batteries, organic radical batteries, supercapacitors, photoelectrochemical cells and photovoltaic devices.

Enhanced Proton Conductivity in Sulfonated Poly(ether ether ketone) Membranes by Incorporating Sodium Dodecyl Benzene Sulfonate

It is of great importance to improve the proton conductivity of proton exchange membranes by easy-handling and cost-efficient approaches. In this work, we incorporated a commercially obtained surfactant, sodium dodecyl benzene sulfonate (SDBS), into sulfonated poly(ether ether ketone) (SPEEK) through solution casting to prepare SPEEK/SDBS membranes. When no more than 10 wt % SDBS was added, the SDBS was well dissolved into the SPEEK matrix, and the activation energy for the proton transfer in the SPEEK/SDBS membranes was greatly reduced, leading to significant enhancement of the membrane proton conductivity. Compared with the SPEEK control membrane, the SPEEK/SDBS membrane with 10 wt % SDBS showed a 78% increase in proton conductivity, up from 0.051 S cm-1 to 0.091 S cm-1, while the water uptake increased from 38% to 62%. Moreover, the SPEEK/SDBS membrane exhibited constant proton conductivity under a long-term water immersion test.