Coupling Dynamic Covalent Bonds and Ionic Crosslinking Network to Promote Shape Memory Properties of Ethylene-vinyl Acetate Copolymers

Recent advances in dynamic covalent bond-based shape memory polymers

Dynamic covalent bond-based shape memory polymers (DCB-SMPs) are one of most important SMPs which have a wide potential application prospect. Different from common strong covalent bonds, DCBs own relatively weak bonding energy, similarly to the supramolecular interactions of noncovalent bonds, and can dynamically combine and dissociate these bonds. DCB-SMP solids, which can be designed to respond for different stimuli, can provide excellent self-healing, good reprocessability, and high mechanical performance, because DCBs can obtain dynamic cross-linking without sacrificing ultrahigh fixing rates. Furthermore, besides DCB-SMP solids, DCB-SMP hydrogels with responsiveness to various stimuli also have been developed recently, which have special biocompatible soft/wet states. Particularly, DCB-SMPs can be combined with emerging 3D-printing techniques to design various original shapes and subsequently complex shape recovery. This review has summarized recent research studies about SMPs based on various DCBs including DCB-SMP solids, DCB-SMP hydrogels, and the introduction of new 3D-printing techniques using them. Last but not least, the advantages/disadvantages of different DCB-SMPs have been analyzed via polymeric structures and the future development trends in this field have been predicted.

Sustained-release capsules coated via thermoforming techniques

Capsule coatings have a wide range of applications as they afford protection to active pharmaceutical ingredients. However, few studies have focused on capsule coating owing to the sensitivity of hard gelatin shells to solvents and high temperature. In the present study, we aimed to coat capsules using two thermoforming coating techniques: vacuum forming coating (VFC) and centrifugal forming coating (CFC). Rheological and mechanical properties were investigated to comprehensively elucidate the processes and mechanisms underlying the two coating techniques. The corresponding coating integrity and drug release behavior were characterized and compared. Herein, we observed that a lower temperature was more suitable for the VFC process than the CFC process. The drug release rate decreased with the film thickness increased. Both optimal VFC and CFC capsules revealed a 24 h sustained-release property following Fick's diffusion law. The coating thickness distribution was more homogeneous for the VFC capsule than the CFC capsule. With the advantage solvent-free of functional capsule coatings, thermoforming coating techniques are convenient and efficient solutions for small-scale personalized coating of oral solid preparations.

Progress in Utilizing Dynamic Bonds to Fabricate Structurally Adaptive Self-Healing, Shape Memory, and Liquid Crystal Polymers

Stimuli-responsive structurally dynamic polymers are capable of mimicking the biological systems to adapt themselves to the surrounding environmental changes and subsequently exhibiting a wide range of responses ranging from self-healing to complex shape-morphing. Dynamic self-healing polymers (SHPs), shape-memory polymers (SMPs) and liquid crystal elastomers (LCEs), which are three representative examples of stimuli-responsive structurally dynamic polymers, have been attracting broad and growing interest in recent years because of their potential applications in the fields of electronic skin, sensors, soft robots, artificial muscles, and so on. We review recent advances and challenges in the developments towards dynamic SHPs, SMPs and LCEs, focusing on the chemistry strategies and the dynamic reaction mechanisms that enhance the performances of the materials including self-healing, reprocessing and reprogramming. We compare and discuss the different dynamic chemistries and their mechanisms on the enhanced functions of the materials, where three summary tables are presented: a library of dynamic bonds and the resulting characteristics of the materials. Finally, we provide a critical outline of the unresolved issues and future perspectives on the emerging developments. This article is protected by copyright. All rights reserved.

Flexible and recyclable bio-based transient resistive memory enabled by self-healing polyimine membrane

The recyclable, self-healing and easily-degradable transient electronic technology has aroused tremendous attention in flexible electronic products. However, integrating the above advantages into one single flexible electronic device is still a huge challenge. Herein, we demonstrate a flexible and recyclable bio-based memory device using fish colloid as the resistive switching layer on a polyimine substrate, which affords reliable mechanical and electrical properties under repetitive conformal deformation operation. This flexible bio-based memory device presents potential analog behaviors including memory characteristics and excitatory current response, which undergoes incremental potentiation in conductance under successive electrical pulses. Moreover, this device is expected to greatly alleviate the environmental problems caused by electronic waste. It can be decomposed rapidly in water and well recycled, which is a promising candidate for transient memories and information security. We believe that this study can provide new possibilities to the field of high-performance transient electronics and flexible resistive memory devices.

Piezoelectric and Electromechanical Characteristics of Porous Poly(Ethylene-co-Vinyl Acetate) Copolymer Films for Smart Sensors and Mechanical Energy Harvesting Applications

This paper investigates energy harvesting performances of porous piezoelectric polymer films to collect electrical energy from vibrations and power various sensors. The influence of void content on the elastic matrix, dielectric, electrical, and mechanical properties of porous piezoelectric polymer films produced from available commercial poly(ethylene-co-vinyl acetate) using an industrially applicable melt-state extrusion method (EVA) were examined and discussed. Electrical and mechanical characterization showed an increase in the harvested current and a decrease in Young’s modulus with the increasing ratio of voids. Thermal analysis revealed a decrease in piezoelectric constant of the porous materials. The authors present a mathematical model that is able to predict harvested current as a function of matrix characteristics, mechanical excitation and porosity percentage. The output current is directly proportional to the porosity percentage. The harvested power significantly increases with increasing strain or porosity, achieving a power value up to 0.23, 1.55, and 3.87 mW/m3 for three EVA compositions: EVA 0%, EVA 37% and EVA 65%, respectively. In conclusion, porous piezoelectric EVA films has great potential from an energy density viewpoint and could represent interesting candidates for energy harvesting applications. Our work contributes to the development of smart materials, with potential uses as innovative harvester systems of energy generated by different vibration sources such as roads, machines and oceans.

Basic Approaches to the Design of Intrinsic Self-Healing Polymers for Triboelectric Nanogenerators

Triboelectric nanogenerators (TENGs) as a revolutionary system for harvesting mechanical energy have demonstrated high vitality and great advantage, which open up great prospects for their application in various areas of the society of the future. The past few years have seen exponential growth in many new classes of self-healing polymers (SHPs) for TENGs. This review presents and evaluates the SHP range for TENGs, and also attempts to assess the impact of modern polymer chemistry on the development of advanced materials for TENGs. Among the most widely used SHPs for TENGs, the analysis of non-covalent (hydrogen bond, metal-ligand bond), covalent (imine bond, disulfide bond, borate bond) and multiple bond-based SHPs in TENGs has been performed. Particular attention is paid to the use of SHPs with shape memory as components of TENGs. Finally, the problems and prospects for the development of SHPs for TENGs are outlined.