1
|
Bi Y, Gao J, Zhang Y, Zhang Y, Du K, Su J, Zhang S. In-situ construction of chitosan@tannin structure on bamboo fiber for green and convenient reinforcement of poly(3-hydroxybutyrate) biocomposite. Int J Biol Macromol 2024; 278:134954. [PMID: 39187105 DOI: 10.1016/j.ijbiomac.2024.134954] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 05/02/2024] [Revised: 07/26/2024] [Accepted: 08/20/2024] [Indexed: 08/28/2024]
Abstract
Fiber-reinforced biocomposites were widely considered as the optimal sustainable alternative to traditional petroleum-based polymers due to their renewable, degradable, and environmentally friendly characteristics, along with economic benefits. However, the poor interfacial bonding between the matrix and natural fiber reinforcement remained a key issue limiting their mechanical and thermal properties. Focusing on cost-effective, convenient, and low-pollution chemical methods, this work proposed a strategy for in-situ synthesis of composite structures on bamboo fiber (BF) surfaces. Crude chitosan (CS) and reclaimed tannic acid (TA) were utilized as the raw materials, to construct stereo-netlike chitosan @ tannin structures (CS@TA) via a one-pot method facilitated by hydrogen bonding and complexation. The influence of reactant concentration and pH value on the process was further investigated and optimized. The CS@TA structure improved the interfacial bonding between the BF reinforcement and matrix poly(3-hydroxybutyrate) (PHB), and this non-amino-driven construction provided a potential reaction platform for functionalizing the interfacial layer. The modified biocomposite showed improvements in tensile and impact strengths (51.58 %, 41.18 %), also in tensile and flexural moduli (13.59 %, 26.88 %). Enhancements were also observed in thermal properties and heat capacity. This work presents a simple and promising approach to increase biocomposite interface bonding.
Collapse
Affiliation(s)
- Yanbin Bi
- Key Laboratory of Wood Material Science and Application (Beijing Forestry University), Ministry of Education, Beijing 100083, China; Beijing Key Laboratory of Wood Science and Engineering, Beijing Forestry University, Beijing 100083, China
| | - Jian Gao
- Key Laboratory of Wood Material Science and Application (Beijing Forestry University), Ministry of Education, Beijing 100083, China; Beijing Key Laboratory of Wood Science and Engineering, Beijing Forestry University, Beijing 100083, China
| | - Yutong Zhang
- Key Laboratory of Wood Material Science and Application (Beijing Forestry University), Ministry of Education, Beijing 100083, China; Beijing Key Laboratory of Wood Science and Engineering, Beijing Forestry University, Beijing 100083, China
| | - Yi Zhang
- Key Laboratory of Wood Material Science and Application (Beijing Forestry University), Ministry of Education, Beijing 100083, China; Beijing Key Laboratory of Wood Science and Engineering, Beijing Forestry University, Beijing 100083, China
| | - Keke Du
- Key Laboratory of Wood Material Science and Application (Beijing Forestry University), Ministry of Education, Beijing 100083, China; Beijing Key Laboratory of Wood Science and Engineering, Beijing Forestry University, Beijing 100083, China
| | - Jixing Su
- Key Laboratory of Wood Material Science and Application (Beijing Forestry University), Ministry of Education, Beijing 100083, China; Beijing Key Laboratory of Wood Science and Engineering, Beijing Forestry University, Beijing 100083, China
| | - Shuangbao Zhang
- Key Laboratory of Wood Material Science and Application (Beijing Forestry University), Ministry of Education, Beijing 100083, China; Beijing Key Laboratory of Wood Science and Engineering, Beijing Forestry University, Beijing 100083, China.
| |
Collapse
|
2
|
Jordà-Reolid M, Moreno V, Martínez-Garcia A, Covas JA, Gomez-Caturla J, Ivorra-Martinez J, Quiles-Carrillo L. Incorporation of Argan Shell Flour in a Biobased Polypropylene Matrix for the Development of High Environmentally Friendly Composites by Injection Molding. Polymers (Basel) 2023; 15:2743. [PMID: 37376389 DOI: 10.3390/polym15122743] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 05/18/2023] [Revised: 06/14/2023] [Accepted: 06/16/2023] [Indexed: 06/29/2023] Open
Abstract
In this study, a new composite material is developed using a semi bio-based polypropylene (bioPP) and micronized argan shell (MAS) byproducts. To improve the interaction between the filler and the polymer matrix, a compatibilizer, PP-g-MA, is used. The samples are prepared using a co-rotating twin extruder followed by an injection molding process. The addition of the MAS filler improves the mechanical properties of the bioPP, as evidenced by an increase in tensile strength from 18.2 MPa to 20.8 MPa. The reinforcement is also observed in the thermomechanical properties, with an increased storage modulus. The thermal characterization and X-ray diffraction indicate that the addition of the filler leads to the formation of α structure crystals in the polymer matrix. However, the addition of a lignocellulosic filler also leads to an increased affinity for water. As a result, the water uptake of the composites increases, although it remains relatively low even after 14 weeks. The water contact angle is also reduced. The color of the composites changes to a color similar to wood. Overall, this study demonstrates the potential of using MAS byproducts to improve their mechanical properties. However, the increased affinity with water should be taken into account in potential applications.
Collapse
Affiliation(s)
- María Jordà-Reolid
- Innovative Materials and Manufacturing Area-AIJU, Technological Institute for Children's Products & Leisure, 03440 Ibi, Spain
| | - Virginia Moreno
- Institute of Materials Technology (ITM), Universitat Politècnica de València (UPV), Plaza Ferrándiz y Carbonell s/n, 03801 Alcoy, Spain
| | - Asunción Martínez-Garcia
- Innovative Materials and Manufacturing Area-AIJU, Technological Institute for Children's Products & Leisure, 03440 Ibi, Spain
| | - José A Covas
- Institute for Polymers and Composites, University of Minho, 4804-533 Guimaraes, Portugal
| | - Jaume Gomez-Caturla
- Institute of Materials Technology (ITM), Universitat Politècnica de València (UPV), Plaza Ferrándiz y Carbonell s/n, 03801 Alcoy, Spain
| | - Juan Ivorra-Martinez
- Institute of Materials Technology (ITM), Universitat Politècnica de València (UPV), Plaza Ferrándiz y Carbonell s/n, 03801 Alcoy, Spain
| | - Luis Quiles-Carrillo
- Institute of Materials Technology (ITM), Universitat Politècnica de València (UPV), Plaza Ferrándiz y Carbonell s/n, 03801 Alcoy, Spain
| |
Collapse
|
3
|
Green Composites from Partially Bio-Based Poly(butylene succinate-co-adipate)-PBSA and Short Hemp Fibers with Itaconic Acid-Derived Compatibilizers and Plasticizers. Polymers (Basel) 2022; 14:polym14101968. [PMID: 35631851 PMCID: PMC9145613 DOI: 10.3390/polym14101968] [Citation(s) in RCA: 5] [Impact Index Per Article: 2.5] [Reference Citation Analysis] [Abstract] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 04/20/2022] [Revised: 05/05/2022] [Accepted: 05/10/2022] [Indexed: 11/16/2022] Open
Abstract
In this work, green composites have been developed and characterized using a bio-based polymeric matrix such as BioPBSA and the introduction of 30 wt.% short hemp fibers as a natural reinforcement to obtain materials with maximum environmental efficiency. In order to increase the interfacial adhesion between the matrix and the fiber to obtain better properties in the composites, a reactive extrusion process has been carried out. On the one hand, different additives derived from bio-based itaconic acid have been added to the BioPBSA/HEMP composite, such as dibutyl itaconate (DBI) and a copolymer of PBSA grafted with itaconic acid (PBSA-g-IA). On the other hand, a different copolymer of PBSA grafted with maleic anhydride (PBSA-g-MA) was also tested. The resulting composites have been processed by injection-molding to obtain different samples which were evaluated in terms of mechanical, thermal, chemical, dynamic-mechanical, morphological and wettability and color properties. In relation to the mechanical properties, the incorporation of hemp fibers resulted in an increase in the stiffness of the base polymer. The tensile modulus of pure BioPBSA increased from 281 MPa to 3482 MPa with 30% fiber. The addition of DBI shows a remarkable improvement in the ductility of the composites, while copolymers with IA and MA, generate mechanically balanced composites. In terms of thermal properties, the incorporation of hemp fiber and compatibilizing agents led to a reduction in thermal stability. However, from the point of view of thermomechanical properties, a clear increase in rigidity is achieved throughout the temperature range studied. As far as the color of the samples is concerned, the incorporation of hemp generates a typical color, while the incorporation of the compatibilizing agents does not modify this color excessively. Finally, the introduction of lignocellulosic fibers greatly affects water absorption and contact angle, although the use of additives helped to mitigate this effect.
Collapse
|
4
|
Eraslan K, Aversa C, Nofar M, Barletta M, Gisario A, Salehiyan R, Alkan Goksu Y. Poly(3-hydroxybutyrate-co-3-hydroxyhexanoate) (PHBH): synthesis, properties, and applications - A Review. Eur Polym J 2022. [DOI: 10.1016/j.eurpolymj.2022.111044] [Citation(s) in RCA: 2] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 12/25/2022]
|
5
|
Dolçà C, Fages E, Gonga E, Garcia-Sanoguera D, Balart R, Quiles-Carrillo L. The Effect of Varying the Amount of Short Hemp Fibers on Mechanical and Thermal Properties of Wood-Plastic Composites from Biobased Polyethylene Processed by Injection Molding. Polymers (Basel) 2021; 14:polym14010138. [PMID: 35012159 PMCID: PMC8747228 DOI: 10.3390/polym14010138] [Citation(s) in RCA: 4] [Impact Index Per Article: 1.3] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 12/15/2021] [Revised: 12/27/2021] [Accepted: 12/28/2021] [Indexed: 11/16/2022] Open
Abstract
Biobased HDPE (bioHDPE) was melt-compounded with different percentages (2.5 to 40.0 wt.%) of short hemp fibers (HF) as a natural reinforcement to obtain environmentally friendly wood plastic composites (WPC). These WPC were melt-compounded using a twin-screw extrusion and shaped into standard samples by injection molding. To improve the poor compatibility between the high non-polar BioHDPE matrix and the highly hydrophilic lignocellulosic fibers, a malleated copolymer, namely, polyethylene-graft-maleic anhydride (PE-g-MA), was used. The addition of short hemp fibers provided a remarkable increase in the stiffness that, in combination with PE-g-MA, led to good mechanical performance. In particular, 40 wt.% HF drastically increased the Young’s modulus and impact strength of BioHDPE, reaching values of 5275 MPa and 3.6 kJ/m2, respectively, which are very interesting values compared to neat bioHDPE of 826 MPa and 2.0 kJ/m2. These results were corroborated by dynamic mechanical thermal analysis (DMTA) results, which revealed a clear increasing tendency on stiffness with increasing the fiber loading over the whole temperature range. The crystal structure was not altered by the introduction of the natural fibers as could be seen in the XRD patterns in which mainly the heights of the main peaks changed, and only small peaks associated with the presence of the fiber appeared. Analysis of the thermal properties of the composites showed that no differences in melting temperature occurred and the non-isothermal crystallization process was satisfactorily described from the combined Avrami and Ozawa model. As for the thermal degradation, the introduction of HF resulted in the polymer degradation taking place at a higher temperature. As for the change in color of the injected samples, it was observed that the increase in fiber generated a clear modification in the final shades of the pieces, reaching colors very similar to dark woods for percentages higher than 20% HF. Finally, the incorporation of an increasing percentage of fibers also increased water absorption due to its lignocellulosic nature in a linear way, which drastically improved the polarity of the composite.
Collapse
Affiliation(s)
- Celia Dolçà
- Textile Industry Research Association (AITEX), Plaza Emilio Sala, 1, 03801 Alcoy, Spain; (C.D.); (E.F.); (E.G.)
| | - Eduardo Fages
- Textile Industry Research Association (AITEX), Plaza Emilio Sala, 1, 03801 Alcoy, Spain; (C.D.); (E.F.); (E.G.)
| | - Eloi Gonga
- Textile Industry Research Association (AITEX), Plaza Emilio Sala, 1, 03801 Alcoy, Spain; (C.D.); (E.F.); (E.G.)
| | - David Garcia-Sanoguera
- Technological Institute of Materials (ITM), Universitat Politècnica de València (UPV), Plaza Ferrándiz y Carbonell, 1, 03801 Alcoy, Spain; (D.G.-S.); (R.B.)
| | - Rafael Balart
- Technological Institute of Materials (ITM), Universitat Politècnica de València (UPV), Plaza Ferrándiz y Carbonell, 1, 03801 Alcoy, Spain; (D.G.-S.); (R.B.)
| | - Luis Quiles-Carrillo
- Technological Institute of Materials (ITM), Universitat Politècnica de València (UPV), Plaza Ferrándiz y Carbonell, 1, 03801 Alcoy, Spain; (D.G.-S.); (R.B.)
- Correspondence: ; Tel.: +34-966-528-433
| |
Collapse
|
6
|
Rojas-Lema S, Arevalo J, Gomez-Caturla J, Garcia-Garcia D, Torres-Giner S. Peroxide-Induced Synthesis of Maleic Anhydride-Grafted Poly(butylene succinate) and Its Compatibilizing Effect on Poly(butylene succinate)/Pistachio Shell Flour Composites. Molecules 2021; 26:molecules26195927. [PMID: 34641470 PMCID: PMC8512837 DOI: 10.3390/molecules26195927] [Citation(s) in RCA: 7] [Impact Index Per Article: 2.3] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 08/02/2021] [Revised: 09/10/2021] [Accepted: 09/24/2021] [Indexed: 11/28/2022] Open
Abstract
Framing the Circular Bioeconomy, the use of reactive compatibilizers was applied in order to increase the interfacial adhesion and, hence, the physical properties and applications of green composites based on biopolymers and food waste derived lignocellulosic fillers. In this study, poly(butylene succinate) grafted with maleic anhydride (PBS-g-MAH) was successfully synthetized by a reactive melt-mixing process using poly(butylene succinate) (PBS) and maleic anhydride (MAH) that was induced with dicumyl peroxide (DCP) as a radical initiator and based on the formation of macroradicals derived from the hydrogen abstraction of the biopolymer backbone. Then, PBS-g-MAH was used as reactive compatibilizer for PBS filled with different contents of pistachio shell flour (PSF) during melt extrusion. As confirmed by Fourier transform infrared (FTIR), PBS-g-MAH acted as a bridge between the two composite phases since it was readily soluble in PBS and could successfully form new esters by reaction of its multiple MAH groups with the hydroxyl (–OH) groups present in cellulose or lignin of PSF and the end ones in PBS. The resultant compatibilized green composites were, thereafter, shaped by injection molding into 4-mm thick pieces with a wood-like color. Results showed significant increases in the mechanical and thermomechanical rigidity and hardness, meanwhile variations on the thermal stability were negligible. The enhancement observed was related to the good dispersion and the improved filler-matrix interfacial interactions achieved by PBS-g-MAH and also to the PSF nucleating effect that increased the PBS’s crystallinity. Furthermore, water uptake of the pieces progressively increased as a function of the filler content, whereas the disintegration in controlled compost soil was limited due to their large thickness.
Collapse
Affiliation(s)
- Sandra Rojas-Lema
- Technological Institute of Materials (ITM), Universitat Politècnica de València (UPV), Plaza Ferrándiz y Carbonell 1, 03801 Alcoy, Spain; (J.A.); (J.G.-C.); (D.G.-G.)
- Correspondence: (S.R.-L.); (S.T.-G.)
| | - Jordi Arevalo
- Technological Institute of Materials (ITM), Universitat Politècnica de València (UPV), Plaza Ferrándiz y Carbonell 1, 03801 Alcoy, Spain; (J.A.); (J.G.-C.); (D.G.-G.)
| | - Jaume Gomez-Caturla
- Technological Institute of Materials (ITM), Universitat Politècnica de València (UPV), Plaza Ferrándiz y Carbonell 1, 03801 Alcoy, Spain; (J.A.); (J.G.-C.); (D.G.-G.)
| | - Daniel Garcia-Garcia
- Technological Institute of Materials (ITM), Universitat Politècnica de València (UPV), Plaza Ferrándiz y Carbonell 1, 03801 Alcoy, Spain; (J.A.); (J.G.-C.); (D.G.-G.)
| | - Sergio Torres-Giner
- Research Institute of Food Engineering for Development (IIAD), Universitat Politècnica de València (UPV), Camino de Vera s/n, 46022 Valencia, Spain
- Correspondence: (S.R.-L.); (S.T.-G.)
| |
Collapse
|
7
|
Biopolymers from Natural Resources. Polymers (Basel) 2021; 13:polym13152532. [PMID: 34372135 PMCID: PMC8347402 DOI: 10.3390/polym13152532] [Citation(s) in RCA: 8] [Impact Index Per Article: 2.7] [Reference Citation Analysis] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 06/30/2021] [Accepted: 07/20/2021] [Indexed: 12/29/2022] Open
|
8
|
Contribution to a Circular Economy Model: From Lignocellulosic Wastes from the Extraction of Vegetable Oils to the Development of a New Composite. Polymers (Basel) 2021; 13:polym13142269. [PMID: 34301027 PMCID: PMC8309261 DOI: 10.3390/polym13142269] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.3] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 06/04/2021] [Revised: 07/01/2021] [Accepted: 07/06/2021] [Indexed: 12/02/2022] Open
Abstract
The present works focuses on the development of a novel fully bio-based composite using a bio-based high-density polyethylene (Bio-HDPE) obtained from sugar cane as matrix and a by-product of extraction of chia seed oil (CO) as filler, with the objective of achieving a circular economy model. The research aims to revalorize an ever-increasing waste stream produced by the growing interest in vegetable oils. From the technical point of view, the chia seed flour (CSF) was chemically modified using a silane treatment. This treatment provides a better interfacial adhesion as was evidenced by the mechanical and thermal properties as well as field emission scanning electron microscopy (FESEM). The effect of silane treatment on water uptake and disintegration rate was also studied. On the other hand, in a second stage, an optimization of the percentage of treated CSF used as filler was carried out by a complete series of mechanical, thermal, morphological, colour, water absorption and disintegration tests with the aim to evaluate the new composite developed using chia by-products. It is noteworthy as the disintegration rate increased with the addition of CSF filler, which leads to obtain a partially biodegradable wood plastic composite (WPC) and therefore, becoming more environmentally friendly.
Collapse
|
9
|
Burgada F, Fages E, Quiles-Carrillo L, Lascano D, Ivorra-Martinez J, Arrieta MP, Fenollar O. Upgrading Recycled Polypropylene from Textile Wastes in Wood Plastic Composites with Short Hemp Fiber. Polymers (Basel) 2021; 13:polym13081248. [PMID: 33921403 PMCID: PMC8070082 DOI: 10.3390/polym13081248] [Citation(s) in RCA: 13] [Impact Index Per Article: 4.3] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 03/18/2021] [Revised: 04/02/2021] [Accepted: 04/07/2021] [Indexed: 11/16/2022] Open
Abstract
This research reports the manufacturing and characterization of green composites made from recycled polypropylene obtained from the remnants of polypropylene non-woven fabrics used in the textile industry and further reinforced with short hemp fibers (SHFs). To improve the interaction of the reinforcing fibers with the recycled polymeric matrix, two types of compatibilizing agents (maleic anhydride grafted, PP-g-MA, and maleinized linseed oil, MLO) were added during melt-processing, the percentage of which had to remain constant concerning the amount of fiber loading to ensure complete reactivity. Standardized test specimens were obtained by injection molding. The composites were characterized by mechanical (tensile, impact, and hardness), thermal (DSC, TGA), thermomechanical, FTIR, and FESEM microscopy tests. In addition, color and water uptake properties were also analyzed. The results show that the addition of PP-g-MA to rPP was satisfactory, thus improving the fiber-matrix interaction, resulting in a marked reinforcing effect of the hemp fibers in the recycled PP matrix, which can be reflected in the increased stiffness of the samples. In parallel to the compatibilizing effect, a plasticizing effect was obtained by incorporating MLO, causing a decrease in the glass transition temperature of the composites by approximately 6 °C and an increase in ductility compared to the unfilled recycled polypropylene samples.
Collapse
Affiliation(s)
- Francisco Burgada
- Textile Research Institute (AITEX), Plaza Emilio Sala 1, 03801 Alcoy, Spain; (F.B.); (E.F.)
| | - Eduardo Fages
- Textile Research Institute (AITEX), Plaza Emilio Sala 1, 03801 Alcoy, Spain; (F.B.); (E.F.)
| | - Luis Quiles-Carrillo
- Technological Institute of Materials (ITM), Universitat Politècnica de València (UPV), Plaza Ferrándiz y Carbonell 1, 03801 Alcoy, Spain; (L.Q.-C.); (D.L.); (J.I.-M.)
| | - Diego Lascano
- Technological Institute of Materials (ITM), Universitat Politècnica de València (UPV), Plaza Ferrándiz y Carbonell 1, 03801 Alcoy, Spain; (L.Q.-C.); (D.L.); (J.I.-M.)
- Escuela Politécnica Nacional, Quito 170517, Ecuador
| | - Juan Ivorra-Martinez
- Technological Institute of Materials (ITM), Universitat Politècnica de València (UPV), Plaza Ferrándiz y Carbonell 1, 03801 Alcoy, Spain; (L.Q.-C.); (D.L.); (J.I.-M.)
| | - Marina P. Arrieta
- Departamento de Ingeniería Química Industrial y del Medio Ambiente, Escuela Técnica Superior de Ingenieros Industriales, Universidad Politécnica de Madrid (ETSII-UPM), C/ José Gutiérrez Abascal 2, 28006 Madrid, Spain;
- Grupo de Investigación: Polímeros, Caracterización y Aplicaciones (POLCA), 28006 Madrid, Spain
| | - Octavio Fenollar
- Technological Institute of Materials (ITM), Universitat Politècnica de València (UPV), Plaza Ferrándiz y Carbonell 1, 03801 Alcoy, Spain; (L.Q.-C.); (D.L.); (J.I.-M.)
- Correspondence: ; Tel.: +34-966-528-433
| |
Collapse
|
10
|
Meléndez-Rodríguez B, Torres-Giner S, Reis MAM, Silva F, Matos M, Cabedo L, Lagarón JM. Blends of Poly(3-Hydroxybutyrate- co-3-Hydroxyvalerate) with Fruit Pulp Biowaste Derived Poly(3-Hydroxybutyrate- co-3-Hydroxyvalerate- co-3-Hydroxyhexanoate) for Organic Recycling Food Packaging. Polymers (Basel) 2021; 13:1155. [PMID: 33916564 PMCID: PMC8038484 DOI: 10.3390/polym13071155] [Citation(s) in RCA: 15] [Impact Index Per Article: 5.0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 03/13/2021] [Revised: 03/25/2021] [Accepted: 03/26/2021] [Indexed: 11/17/2022] Open
Abstract
In the present study, a new poly(3-hydroxybutyrate-co-3-hydroxyvalerate-co-3-hydroxyhexanoate) [P(3HB-co-3HV-co-3HHx)] terpolyester with approximately 68 mol% of 3-hydroxybutyrate (3HB), 17 mol% of 3-hydroxyvalerate (3HV), and 15 mol% of 3-hydroxyhexanoate (3HHx) was obtained via the mixed microbial culture (MMC) technology using fruit pulps as feedstock, a processing by-product of the juice industry. After extraction and purification performed in a single step, the P(3HB-co-3HV-co-3HHx) powder was melt-mixed, for the first time, in contents of 10, 25, and 50 wt% with commercial poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV). Thereafter, the resultant doughs were thermo-compressed to obtain highly miscible films with good optical properties, which can be of interest in rigid and semirigid organic recyclable food packaging applications. The results showed that the developed blends exhibited a progressively lower melting enthalpy with increasing the incorporation of P(3HB-co-3HV-co-3HHx), but retained the PHB crystalline morphology, albeit with an inferred lower crystalline density. Moreover, all the melt-mixed blends were thermally stable up to nearly 240 °C. As the content of terpolymer increased in the blends, the mechanical response of their films showed a brittle-to-ductile transition. On the other hand, the permeabilities to water vapor, oxygen, and, more notably, limonene were seen to increase. On the overall, this study demonstrates the value of using industrial biowaste derived P(3HB-co-3HV-co-3HHx) terpolyesters as potentially cost-effective and sustainable plasticizing additives to balance the physical properties of organic recyclable polyhydroxyalkanoate (PHA)-based food packaging materials.
Collapse
Affiliation(s)
- Beatriz Meléndez-Rodríguez
- Novel Materials and Nanotechnology Group, Institute of Agrochemistry and Food Technology (IATA), Spanish Council for Scientific Research (CSIC), Calle Catedrático Agustín Escardino Benlloch 7, 46980 Paterna, Spain; (B.M.-R.); (S.T.-G.)
| | - Sergio Torres-Giner
- Novel Materials and Nanotechnology Group, Institute of Agrochemistry and Food Technology (IATA), Spanish Council for Scientific Research (CSIC), Calle Catedrático Agustín Escardino Benlloch 7, 46980 Paterna, Spain; (B.M.-R.); (S.T.-G.)
| | - Maria A. M. Reis
- UCIBIO-REQUIMTE-Applied Molecular Biosciences Unit, Chemistry Department, Faculty of Sciences and Technology, New University of Lisbon, 1099-085 Lisbon, Portugal; (M.A.M.R.); (F.S.); (M.M.)
| | - Fernando Silva
- UCIBIO-REQUIMTE-Applied Molecular Biosciences Unit, Chemistry Department, Faculty of Sciences and Technology, New University of Lisbon, 1099-085 Lisbon, Portugal; (M.A.M.R.); (F.S.); (M.M.)
| | - Mariana Matos
- UCIBIO-REQUIMTE-Applied Molecular Biosciences Unit, Chemistry Department, Faculty of Sciences and Technology, New University of Lisbon, 1099-085 Lisbon, Portugal; (M.A.M.R.); (F.S.); (M.M.)
| | - Luis Cabedo
- Polymers and Advanced Materials Group (PIMA), Universitat Jaume I (UJI), 12071 Castellón, Spain;
| | - José María Lagarón
- Novel Materials and Nanotechnology Group, Institute of Agrochemistry and Food Technology (IATA), Spanish Council for Scientific Research (CSIC), Calle Catedrático Agustín Escardino Benlloch 7, 46980 Paterna, Spain; (B.M.-R.); (S.T.-G.)
| |
Collapse
|
11
|
Jorda-Reolid M, Gomez-Caturla J, Ivorra-Martinez J, Stefani PM, Rojas-Lema S, Quiles-Carrillo L. Upgrading Argan Shell Wastes in Wood Plastic Composites with Biobased Polyethylene Matrix and Different Compatibilizers. Polymers (Basel) 2021; 13:polym13060922. [PMID: 33802815 PMCID: PMC8002462 DOI: 10.3390/polym13060922] [Citation(s) in RCA: 12] [Impact Index Per Article: 4.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 02/27/2021] [Revised: 03/12/2021] [Accepted: 03/15/2021] [Indexed: 12/21/2022] Open
Abstract
The present study reports on the development of wood plastic composites (WPC) based on micronized argan shell (MAS) as a filler and high-density polyethylene obtained from sugarcane (Bio-HDPE), following the principles proposed by the circular economy in which the aim is to achieve zero waste by the introduction of residues of argan as a filler. The blends were prepared by extrusion and injection molding processes. In order to improve compatibility between the argan particles and the green polyolefin, different compatibilizers and additional filler were used, namely polyethylene grafted maleic anhydride (PE-g-MA 3 wt.-%), maleinized linseed oil (MLO 7.5 phr), halloysite nanotubes (HNTs 7.5 phr), and a combination of MLO and HNTs (3.75 phr each). The mechanical, morphological, thermal, thermomechanical, colorimetric, and wettability properties of each blend were analyzed. The results show that MAS acts as a reinforcing filler, increasing the stiffness of the Bio-HDPE, and that HNTs further increases this reinforcing effect. MLO and PE-g-MA, altogether with HNTs, improve the compatibility between MAS and Bio-HDPE, particularly due to bonds formed between oxygen-based groups present in each compound. Thermal stability was also improved provided by the addition of MAS and HNTs. All in all, reddish-like brown wood plastic composites with improved stiffness, good thermal stability, enhanced compatibility, and good wettability properties were obtained.
Collapse
Affiliation(s)
- Maria Jorda-Reolid
- Departamento de Materiales y Tecnologías, Asociación de Investigación de la Industria del Juguete, Conexas y Afines (AIJU), Av. de la Industria, 23, 03440 Ibi, Spain; (M.J.-R.); (S.R.-L.)
| | - Jaume Gomez-Caturla
- Instituto de Tecnología de Materiales (ITM), Universitat Politècnica de València (UPV), Plaza Ferrándiz y Carbonell 1, 03801 Alcoy, Spain;
| | - Juan Ivorra-Martinez
- Instituto de Tecnología de Materiales (ITM), Universitat Politècnica de València (UPV), Plaza Ferrándiz y Carbonell 1, 03801 Alcoy, Spain;
- Correspondence: (J.I.-M.); (L.Q.-C.)
| | - Pablo Marcelo Stefani
- Instituto de Investigaciones en Ciencia y Tecnología de Materiales (INTEMA), Consejo Nacional de Investigaciones Científicas y Técnicas (CONICET), Universidad Nacional de Mar del Plata (UNMdP), Av. Colón 10850, Mar del Plata 7600, Argentina;
| | - Sandra Rojas-Lema
- Departamento de Materiales y Tecnologías, Asociación de Investigación de la Industria del Juguete, Conexas y Afines (AIJU), Av. de la Industria, 23, 03440 Ibi, Spain; (M.J.-R.); (S.R.-L.)
| | - Luis Quiles-Carrillo
- Departamento de Materiales y Tecnologías, Asociación de Investigación de la Industria del Juguete, Conexas y Afines (AIJU), Av. de la Industria, 23, 03440 Ibi, Spain; (M.J.-R.); (S.R.-L.)
- Correspondence: (J.I.-M.); (L.Q.-C.)
| |
Collapse
|
12
|
Marset D, Dolza C, Fages E, Gonga E, Gutiérrez O, Gomez-Caturla J, Ivorra-Martinez J, Sanchez-Nacher L, Quiles-Carrillo L. The Effect of Halloysite Nanotubes on the Fire Retardancy Properties of Partially Biobased Polyamide 610. Polymers (Basel) 2020; 12:E3050. [PMID: 33352673 PMCID: PMC7765851 DOI: 10.3390/polym12123050] [Citation(s) in RCA: 6] [Impact Index Per Article: 1.5] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 12/15/2020] [Revised: 12/16/2020] [Accepted: 12/17/2020] [Indexed: 01/31/2023] Open
Abstract
The main objective of the work reported here was the analysis and evaluation of halloysite nanotubes (HNTs) as natural flame retardancy filler in partially biobased polyamide 610 (PA610), with 63% of carbon from natural sources. HNTs are naturally occurring clays with a nanotube-like shape. PA610 compounds containing 10%, 20%, and 30% HNT were obtained in a twin-screw co-rotating extruder. The resulting blends were injection molded to create standard samples for fire testing. The incorporation of the HNTs in the PA610 matrix leads to a reduction both in the optical density and a significant reduction in the number of toxic gases emitted during combustion. This improvement in fire properties is relevant in applications where fire safety is required. With regard to calorimetric cone results, the incorporation of 30% HNTs achieved a significant reduction in terms of the peak values obtained of the heat released rate (HRR), changing from 743 kW/m2 to about 580 kW/m2 and directly modifying the shape of the characteristic curve. This improvement in the heat released has produced a delay in the mass transfer of the volatile decomposition products, which are entrapped inside the HNTs' lumen, making it difficult for the sample to burn. However, in relation to the ignition time of the samples (TTI), the incorporation of HNTs reduces the ignition start time about 20 s. The results indicate that it is possible to obtain polymer formulations with a high renewable content such as PA610, and a natural occurring inorganic filler in the form of a nanotube, i.e., HNTs, with good flame retardancy properties in terms of toxicity, optical density and UL94 test.
Collapse
Affiliation(s)
- David Marset
- Textile Industry Research Association (AITEX), Plaza Emilio Sala 1, 03801 Alcoy, Spain; (D.M.); (C.D.); (E.F.); (E.G.); (O.G.)
| | - Celia Dolza
- Textile Industry Research Association (AITEX), Plaza Emilio Sala 1, 03801 Alcoy, Spain; (D.M.); (C.D.); (E.F.); (E.G.); (O.G.)
| | - Eduardo Fages
- Textile Industry Research Association (AITEX), Plaza Emilio Sala 1, 03801 Alcoy, Spain; (D.M.); (C.D.); (E.F.); (E.G.); (O.G.)
| | - Eloi Gonga
- Textile Industry Research Association (AITEX), Plaza Emilio Sala 1, 03801 Alcoy, Spain; (D.M.); (C.D.); (E.F.); (E.G.); (O.G.)
| | - Oscar Gutiérrez
- Textile Industry Research Association (AITEX), Plaza Emilio Sala 1, 03801 Alcoy, Spain; (D.M.); (C.D.); (E.F.); (E.G.); (O.G.)
| | - Jaume Gomez-Caturla
- Technological Institute of Materials (ITM), Universitat Politècnica de València (UPV), Plaza Ferrándiz y Carbonell 1, 03801 Alcoy, Spain; (J.G.-C.); (L.S.-N.)
| | - Juan Ivorra-Martinez
- Technological Institute of Materials (ITM), Universitat Politècnica de València (UPV), Plaza Ferrándiz y Carbonell 1, 03801 Alcoy, Spain; (J.G.-C.); (L.S.-N.)
| | - Lourdes Sanchez-Nacher
- Technological Institute of Materials (ITM), Universitat Politècnica de València (UPV), Plaza Ferrándiz y Carbonell 1, 03801 Alcoy, Spain; (J.G.-C.); (L.S.-N.)
| | - Luis Quiles-Carrillo
- Technological Institute of Materials (ITM), Universitat Politècnica de València (UPV), Plaza Ferrándiz y Carbonell 1, 03801 Alcoy, Spain; (J.G.-C.); (L.S.-N.)
| |
Collapse
|
13
|
Arai S, Sakakibara S, Mareschal R, Ooi T, Zinn M, Matsumoto K. Biosynthesis of Random-Homo Block Copolymer Poly[Glycolate- ran-3-Hydroxybutyrate (3HB)]- b-Poly(3HB) Using Sequence-Regulating Chimeric Polyhydroxyalkanoate Synthase in Escherichia coli. Front Bioeng Biotechnol 2020; 8:612991. [PMID: 33364233 PMCID: PMC7752996 DOI: 10.3389/fbioe.2020.612991] [Citation(s) in RCA: 4] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 10/01/2020] [Accepted: 11/16/2020] [Indexed: 11/13/2022] Open
Abstract
Glycolate (GL)-containing polyhydroxyalkanoate (PHA) was synthesized in Escherichia coli expressing the engineered chimeric PHA synthase PhaC AR and coenzyme A transferase. The cells produced poly[GL-co-3-hydroxybutyrate (3HB)] with the supplementation of GL and 3HB, thus demonstrating that PhaC AR is the first known class I PHA synthase that is capable of incorporating GL units. The triad sequence analysis using 1H nuclear magnetic resonance indicated that the obtained polymer was composed of two distinct regions, a P(GL-ran-3HB) random segment and P(3HB) homopolymer segment. The random segment was estimated to contain a 71 mol% GL molar ratio, which was much greater than the value (15 mol%) previously achieved by using PhaC1 P s STQK. Differential scanning calorimetry analysis of the polymer films supported the presence of random copolymer and homopolymer phases. The solvent fractionation of the polymer indicated the presence of a covalent linkage between these segments. Therefore, it was concluded that PhaC AR synthesized a novel random-homo block copolymer, P(GL-ran-3HB)-b-P(3HB).
Collapse
Affiliation(s)
- Shuzo Arai
- Graduate School of Chemical Sciences and Engineering, Hokkaido University, Sapporo, Japan
| | - Sayaka Sakakibara
- Graduate School of Chemical Sciences and Engineering, Hokkaido University, Sapporo, Japan
| | - Robin Mareschal
- Department of Engineering, Hokkaido University, Sapporo, Japan
- Institute of Life Technologies, University of Applied Sciences and Arts Western Switzerland (HES-SO Valais-Wallis), Sion, Switzerland
| | - Toshihiko Ooi
- Division of Applied Chemistry, Faculty of Engineering, Hokkaido University, Sapporo, Japan
| | - Manfred Zinn
- Institute of Life Technologies, University of Applied Sciences and Arts Western Switzerland (HES-SO Valais-Wallis), Sion, Switzerland
| | - Ken’ichiro Matsumoto
- Division of Applied Chemistry, Faculty of Engineering, Hokkaido University, Sapporo, Japan
| |
Collapse
|