Influence of the Architecture of Soft Polymer-Functionalized Polymer Nanoparticles on Their Dynamics in Suspension

Blending Approach Preparation of PVA-g-PMA Films with Embedded "Green" Synthesized Silver Nanoparticles for Acetone Optical Detection

The blending approach (also known as the ex-situ approach) was used for the deposition of thin composite films comprising poly(vinyl alcohol-graft-methyl acrylate) (PVA-g-PMA) and silver nanoparticles (AgNPs). Firstly, the copolymer aqueous dispersion was synthesized through the redox polymerization of methyl acrylate (MA) on poly(vinyl alcohol) (PVA) using ammonium cerium (IV) nitrate as the initiator. Then, AgNPs were synthesized through a "green" method using the water extract of lavender based on by-products of the essential oil industry, and then they were blended with the polymer. Dynamic light scattering (DLS) and transmission electron microscopy (TEM) were used to determine nanoparticle size, along with their stability over time in suspension, during the 30-day period. Thin films of the PVA-g-PMA copolymer, with different AgNP volume fractions varying between 0.008 and 0.260%, were deposited via the spin-coating method on Si substrates, and their optical properties were explored. UV-VIS-NIR spectroscopy and non-linear curve fitting were used for the determination of the refractive index, extinction coefficient, and thickness of the films, while photoluminescence measurements at room temperature were conducted for studying the emission of the films. The concentration dependence of film thickness was observed and showed that thickness increased linearly from 31 nm to 75 nm when the nanoparticles' weight content increased from 0.3 wt% to 2.3 wt%. The sensing properties toward acetone vapors were tested in a controlled atmosphere by measuring reflectance spectra before and during exposure to the analyte molecules in the same film spot; the swelling degree of films was calculated and compared to the corresponding undoped samples. It was shown that the concentration of AgNPs of 1.2 wt% in the films is optimal for the enhancement of the sensing response toward acetone. The influence of AgNPs on the films' properties was revealed and discussed.

Dynamic Mixing Behaviors of Ionically Tethered Polymer Canopy of Nanoscale Hybrid Materials in Fluids of Varying Physical and Chemical Properties

An emerging area of sustainable energy and environmental research is focused on the development of novel electrolytes that can increase the solubility of target species and improve subsequent reaction performance. Electrolytes with chemical and structural tunability have allowed for significant advancements in flow batteries and CO₂ conversion integrated with CO₂ capture. Liquid-like nanoparticle organic hybrid materials (NOHMs) are nanoscale fluids that are composed of inorganic nanocores and an ionically tethered polymeric canopy. NOHMs have been shown to exhibit enhanced conductivity making them promising for electrolyte applications, though they are often challenged by high viscosity in the neat state. In this study, a series of binary mixtures of NOHM-I-HPE with five different secondary fluids, water, chloroform, toluene, acetonitrile, and ethyl acetate, were prepared to reduce the fluid viscosity and investigate the effects of secondary fluid properties (e.g., hydrogen bonding ability, polarity, and molar volume) on their transport behaviors, including viscosity and diffusivity. Our results revealed that the molecular ratio of secondary fluid to the ether groups of Jeffamine M2070 (λ_SF) was able to describe the effect that secondary fluid has on transport properties. Our findings also suggest that in solution, the Jeffamine M2070 molecules exist in different nanoscale environments, where some are more strongly associated with the nanoparticle surface than others, and the conformation of the polymer canopy was dependent on the secondary fluid. This understanding of the polymer conformation in NOHMs can allow for the better design of an electrolyte capable of capturing and releasing small gaseous or ionic species.

Polymer Adsorbents vs. Functionalized Oxides and Carbons: Particulate Morphology and Textural and SurfaceCharacteristics

Various methods for morphological, textural, and structural characterization of polymeric, carbon, and oxide adsorbents have been developed and well described. However, there are ways to improve the quantitative information extraction from experimental data for describing complex sorbents and polymer fillers. This could be based not only on probe adsorption and electron microscopies (TEM, SEM) but also on small-angle X-ray scattering (SAXS), cryoporometry, relaxometry, thermoporometry, quasi-elastic light scattering, Raman and infrared spectroscopies, and other methods. To effectively extract information on complex materials, it is important to use appropriate methods to treat the data with adequate physicomathematical models that accurately describe the dependences of these data on pressure, concentration, temperature, and other parameters, and effective computational programs. It is shown that maximum accurate characterization of complex materials is possible if several complemented methods are used in parallel, e.g., adsorption and SAXS with self-consistent regularization procedures (giving pore size (PSD), pore wall thickness (PWTD) or chord length (CLD), and particle size (PaSD) distribution functions, the specific surface area of open and closed pores, etc.), TEM/SEM images with quantitative treatments (giving the PaSD, PSD, and PWTD functions), as well as cryo- and thermoporometry, relaxometry, X-ray diffraction, infrared and Raman spectroscopies (giving information on the behavior of the materials under different conditions).