Cigarette Butt Waste as Material for Phase Inverted Membrane Fabrication Used for Oil/Water Emulsion Separation

Cellulose acetate, a source from discarded cigarette butts for the development of mixed matrix loose nanofiltration membranes for selective separation

This study presents an environmentally friendly method for extracting cellulose acetate (CA) from discarded cigarette filters, which is then utilized in the fabrication of cellulose-based membranes designed for high flux and rejection rates. CA membranes are likeable to separate dyes and ions, but their separation efficiency is exposed when the contaminant concentration is very low. So, we have integrated graphene oxide (GO) and carboxylated titanium dioxide (COOH-TiO2) in CA to develop mixed matrix membranes (MMMs) and studied them against dyes and most used salts. The CA has been extracted from these butts and added GO and COOH-TiO2 nanoparticles to develop MMMs. The present work administers the effective separation of five dyes (methyl orange, methyl violet, methylene blue, cresol red, and malachite green) and salts (NaCl and Na2SO4) along with the high efficiency of water flux by prepared CA membranes. The prepared membranes rejected up to 94.94 % methyl violet, 91.28 % methyl orange, 88.28 % methylene blue, 89.91 % cresol red, and 91.70 % malachite green dye. Along with the dyes, the membranes showed ∼40.40 % and ∼ 42.97 % rejection of NaCl and Na2SO4 salts, respectively. Additionally, these membranes have tensile strength up to 1.54 MPa. Various characterization techniques were performed on all prepared CA membranes to comprehend their behaviour. The antibacterial activity of MMMs was investigated using the Muller-Hinton-Disk diffusion method against the gram-positive bacterium Staphylococcus aureus (S. aureus) and the gram-negative bacterium Escherichia coli (E. coli). We believe the present work is an approach to utilizing waste materials into valuable products for environmental care.

Sustainability in Membrane Technology: Membrane Recycling and Fabrication Using Recycled Waste

Membrane technology has shown a promising role in combating water scarcity, a globally faced challenge. However, the disposal of end-of-life membrane modules is problematic as the current practices include incineration and landfills as their final fate. In addition, the increase in population and lifestyle advancement have significantly enhanced waste generation, thus overwhelming landfills and exacerbating environmental repercussions and resource scarcity. These practices are neither economically nor environmentally sustainable. Recycling membranes and utilizing recycled material for their manufacturing is seen as a potential approach to address the aforementioned challenges. Depending on physiochemical conditions, the end-of-life membrane could be reutilized for similar, upgraded, and downgraded operations, thus extending the membrane lifespan while mitigating the environmental impact that occurred due to their disposal and new membrane preparation for similar purposes. Likewise, using recycled waste such as polystyrene, polyethylene terephthalate, polyvinyl chloride, tire rubber, keratin, and cellulose and their derivates for fabricating the membranes can significantly enhance environmental sustainability. This study advocates for and supports the integration of sustainability concepts into membrane technology by presenting the research carried out in this area and rigorously assessing the achieved progress. The membranes' recycling and their fabrication utilizing recycled waste materials are of special interest in this work. Furthermore, this study offers guidance for future research endeavors aimed at promoting environmental sustainability.

Robust microfluidic construction of polyvinyl pyrrolidone microfibers incorporated with W/O emulsions stabilized by amphiphilic konjac glucomannan

In this work, we prepared polyvinyl pyrrolidone (PVP) microfibers incorporated water-in-oil (W/O) emulsions. The W/O emulsions were fabricated by hexadecyl konjac glucomannan (HKGM, emulsifier), corn oil (oil phase) and purple corn anthocyanins (PCAs, water phase). The structures and functions of emulsions and microfibers were characterized by confocal laser scanning (CLSM) and scanning electron microscopy (SEM), Fourier transform infrared (FT-IR), Raman and nuclear magnetic resonance (NMR) spectroscopy. The results showed that W/O emulsions exhibited good storage stability for 30 d. Microfibers presented ordered and uniform arrays. Compared with pure PVP microfiber films, the addition of W/O emulsions with PCAs improved the water resistance (WVP from 1.28 to 0.76 g mm/m² day kPa), mechanical strength (Elongation at break from 18.35 % to 49.83 %), antioxidation (free radical scavenging rate from 2.58 % to 16.37 %), and antibacterial activity (inhibition zone against E. coli: 27.33 mm and inhibition zone against S. aureus: 28.33 mm) of microfiber films. Results showed that microfiber film exhibited controlled release of PCAs in W/O emulsions, and about 32 % of the PCAs were released from the microfiber film after 340 min. The as-prepared microfiber films exhibited potential applications for food packaging.

3D Printed and Conventional Membranes—A Review

Polymer membranes are central to the proper operation of several processes used in a wide range of applications. The production of these membranes relies on processes such as phase inversion, stretching, track etching, sintering, or electrospinning. A novel and competitive strategy in membrane production is the use of additive manufacturing that enables the easier manufacture of tailored membranes. To achieve the future development of better membranes, it is necessary to compare this novel production process to that of more conventional techniques, and clarify the advantages and disadvantages. This review article compares a conventional method of manufacturing polymer membranes to additive manufacturing. A review of 3D printed membranes is also done to give researchers a reference guide. Membranes from these two approaches were compared in terms of cost, materials, structures, properties, performance. and environmental impact. Results show that very few membrane materials are used as 3D-printed membranes. Such membranes showed acceptable performance, better structures, and less environmental impact compared with those of conventional membranes.

Waste Reutilization in Polymeric Membrane Fabrication: A New Direction in Membranes for Separation

In parallel to the rapid growth in economic and social activities, there has been an undesirable increase in environmental degradation due to the massively produced and disposed waste. The need to manage waste in a more innovative manner has become an urgent matter. In response to the call for circular economy, some solid wastes can offer plenty of opportunities to be reutilized as raw materials for the fabrication of functional, high-value products. In the context of solid waste-derived polymeric membrane development, this strategy can pave a way to reduce the consumption of conventional feedstock for the production of synthetic polymers and simultaneously to dampen the negative environmental impacts resulting from the improper management of these solid wastes. The review aims to offer a platform for overviewing the potentials of reutilizing solid waste in liquid separation membrane fabrication by covering the important aspects, including waste pretreatment and raw material extraction, membrane fabrication and characterizations, as well as the separation performance evaluation of the resultant membranes. Three major types of waste-derived polymeric raw materials, namely keratin, cellulose, and plastics, are discussed based on the waste origins, limitations in the waste processing, and their conversion into polymeric membranes. With the promising material properties and viability of processing facilities, recycling and reutilization of waste resources for membrane fabrication are deemed to be a promising strategy that can bring about huge benefits in multiple ways, especially to make a step closer to sustainable and green membrane production.