The High Flux of Superhydrophilic-Superhydrophobic Janus Membrane of cPVA-PVDF/PMMA/GO by Layer-by-Layer Electrospinning for High Efficiency Oil-Water Separation

Fabrication of a Janus Copper Mesh by SiO2 Spraying for Unidirectional Water Transportation and Oil/Water Separation

Massive discharge of oily wastewater and frequent occurrence of offshore oil spills have posed an enormous threat to the socioeconomic and ecological environments. Janus membranes with asymmetric wettability properties have great potential for oil/water separation applications and have attracted widespread attention. However, existing Janus membranes still suffer from complex and costly manufacturing processes, low permeability, and poor recyclability. Herein, a novel and facile strategy was proposed to fabricate a Janus copper mesh with opposite wettability for unidirectional water transport and efficient oil/water separation. The hydrophilic side of the Janus copper mesh was prepared by coating it with Cu(OH)2 nanoneedles via a chemical oxidation method. The hydrophobic side was fabricated by coating it with hydrophobic SiO2 nanoparticles via a facile spraying method. The as-prepared Janus copper mesh showed asymmetric surface wettability, which can achieve unidirectional water transport and efficient oil/water separation with excellent recyclability, exhibiting great application potential for droplet manipulation and wastewater purification.

The Design of PAN-Based Janus Membrane with Adjustable Asymmetric Wettability in Wastewater Purification

In this paper, an environmentally friendly polyacrylonitrile-based (PAN-based) composite membrane with a Janus structure for wastewater treatment was successfully fabricated. To achieve the optimum adsorption of PAN-based Janus composite membrane, the asymmetric wettability was regulated through electrospinning, resulting in TiO2 modifying PAN as the hydrophilic substrate layer, and PCL gaining a different thickness as the hydrophobic layer. The prepared Janus composite membrane (PAN/TiO2-PCL20) showed excellent oil/water separation performance for diverse surfactant-stabilized oil-in-water emulsions. For n-hexane-in-water emulsion, the permeate flux and separation efficiency reached 1344 L m-2 h-1 and 99.52%, respectively. Even after 20 cycles of separation, it still had outstanding reusability and the separation efficiency remained above 99.15%. Meanwhile, the PAN/TiO2-PCL20 also exhibited an excellent photocatalytic activity, and the removal rate for RhB reached 93.2%. In addition, the research revealed that PAN/TiO2-PCL20 possessed good mechanical property and unidirectional water transfer capability. All results indicated that PAN/TiO2-PCL20 with photocatalysis and oil/water separation performance could be used for practical complex wastewater purification.

"Biomass to Membrane": Sulfonated Kraft Lignin/PCL Superhydrophilic Electrospun Membrane for Gravity-Driven Oil-in-Water Emulsion Separation

Biobased membranes made with green solvents have numerous advantages in the water purification industry; however, their long-term use is impeded by severe membrane fouling and low structural stability. Herein, we proposed a facile and green approach to fabricate an eco-friendly and biodegradable electrospun membrane by simply blending polycaprolactone (PCL) with sulfonated kraft lignin (SKL) in a green solvent (i.e., acetic acid) without needing any additional post-treatment. We investigated the influence of SKL content on the surface morphology, chemical composition, and mechanical properties of the electrospun membrane. The SKL-modified membranes (L-5 and L-10) showed superhydrophilicity and underwater superoleophobicity with a water contact angle (WCA) of 0° (<3 s) and an underwater-oil contact angle (UWOCA) over 150° due to the combined effect of surface roughness and hydrophilic chemical functionality. Furthermore, the as-prepared membranes demonstrated excellent pure water flux of 800-900 LMH and an emulsion flux of 170-480 LMH during the gravity-driven filtration of three surfactant-stabilized oil-in-water emulsions, namely, mineral oil/water, gasoline/water, and n-hexadecane/water emulsions. In addition, these membranes exhibited superior antioil-fouling performance with excellent separation efficiency (97-99%) and a high flux recovery ratio (>98%). The 10 wt % SKL-incorporated membrane (L-10) also showed consistent separation performance after 10 cyclic tests, indicating its excellent reusability and recyclability. Furthermore, the stability of the membrane under harsh pH conditions was also evaluated and proved to be robust enough to maintain its wettability in a wide pH range (pH 1-10).

Progress on Improved Fouling Resistance-Nanofibrous Membrane for Membrane Distillation: A Mini-Review

Nanofibrous membranes for membrane distillation (MD) have demonstrated promising results in treating various water and wastewater streams. Significant progress has been made in recent decades because of the development of sophisticated membrane materials, such as superhydrophobic, omniphobic and Janus membranes. However, fouling and wetting remain crucial issues for long-term operation. This mini-review summarizes ideas as well as their limitations in understanding the fouling in membrane distillation, comprising organic, inorganic and biofouling. This review also provides progress in developing antifouling nanofibrous membranes for membrane distillation and ongoing modifications on nanofiber membranes for improved membrane distillation performance. Lastly, challenges and future ways to develop antifouling nanofiber membranes for MD application have been systematically elaborated. The present mini-review will interest scientists and engineers searching for the progress in MD development and its solutions to the MD fouling issues.

Enhancing Mechanical Properties and Flux of Nanofibre Membranes for Water Filtration

Nanofibres have gained attention for their highly porous structure, narrow pore size, and high specific surface area. One of the most efficient techniques for producing nanofibres is electrospinning. These fibres are used in various fields, including water filtration. Although they possess the ability to filter various components, the fibres generally have low mechanical strength, which can mitigate their performance over time. To address this, studies have focused on enhancing nanofibre membrane strength for water filtration. Previous analyses show that the mechanical properties of nanofibre mats can be improved through solvent vapour treatment, thermal treatment, and chemical crosslinking. These treatments promote interfibre bonding, leading to the improvement of mechanical strength. However, excessive treatment alters nanofibre behaviour. Excessive heat exposure reduces interfibre bonding, while too much solvent vapour decreases pore size and mechanical strength. Thus, a comprehensive understanding of these post-treatments is crucial. This review examines post-treatments aiming to increase the mechanical strength of nanofibre mats, discussing their advantages and disadvantages. Understanding these treatments is essential for optimising nanofibre membrane performance in water filtration and other applications.

Recent developments in the application of membrane separation technology and its challenges in oil-water separation: A review

In the development and production process of domestic and foreign oil fields, large amounts of oil-bearing wastewater with complex compositions containing toxic and harmful pollutants are generated. These oil-bearing wastewaters will cause serious environmental pollution if they are not effectively treated before discharge. Among these wastewaters, the oily sewage produced in the process of oilfield exploitation has the largest content of oil-water emulsion. In order to solve the problem of oil-water separation of oily sewage, the paper summarizes the research of many scholars in many aspects, such as the use of physical and chemical methods such as air flotation and flocculation, or the use of mechanical methods such as centrifuges and oil booms for sewage treatment. Comprehensive analysis shows that among these oil-water separation methods, membrane separation technology has higher separation efficiency in the separation of general oil-water emulsions than other methods and also exhibits a better separation effect for stable emulsions, which has a broader application prospect for future developments. To present the characteristics of different types of membranes more intuitively, this paper describes the applicable conditions and characteristics of various types of membranes in detail, summarizes the shortcomings of existing membrane separation technologies, and offers prospects for future research directions.

Studies on the Application of Polyimidobenzimidazole Based Nanofiber Material as the Separation Membrane of Lithium-Ion Battery

Aromatic polyimide has good mechanical properties and high-temperature resistance. Based on this, benzimidazole is introduced into the main chain, and its intermolecular (internal) hydrogen bond can increase mechanical and thermal properties and electrolyte wettability. Aromatic dianhydride 4,4'-oxydiphthalic anhydride (ODPA) and benzimidazole-containing diamine 6,6'-bis [2-(4-aminophenyl)benzimidazole] (BAPBI) were synthesized by means of a two-step method. Imidazole polyimide (BI-PI) was used to make a nanofiber membrane separator (NFMS) by electrospinning process, using its high porosity and continuous pore characteristics to reduce the ion diffusion resistance of the NFMS, enhancing the rapid charge and discharge performance. BI-PI has good thermal properties, with a Td5% of 527 °C and a dynamic mechanical analysis Tg of 395 °C. The tensile strength of the NFMS increased from 10.92MPa to 51.15MPa after being hot-pressed. BI-PI has good miscibility with LIB electrolyte, the porosity of the film is 73%, and the electrolyte absorption rate reaches 1454%. That explains the higher ion conductivity (2.02 mS cm^-1) of NFMS than commercial one (0.105 mS cm^-1). When applied to LIB, it is found that it has high cyclic stability and excellent rate performance at high current density (2 C). BI-PI (120 Ω) has a lower charge transfer resistance than the commercial separator Celgard H1612 (143 Ω).

Stretchable, durable and asymmetrically wettable nanofiber composites with unidirectional water transportation capability for temperature sensing

The one-way transportation of liquids plays an important role in smart and wearable electronics. Here, we report an asymmetric nanofibrous membrane (ANM) with unidirectional water transport (UWT) capability by integrating one superhydrophilic MXene/Chitosan/Polyurethane (PU) nanofiber membrane (MCPNM) and one ultrathin hydrophobic PU/Polyvinylpyrrolidone (PVP) layer with a "bead-on-string" structure. The UWT performance shows long-term stability and can be well maintained during the cyclic stretching, abrasion and ultrasonic washing tests. The ANM exhibits negative temperature coefficient and is served as a temperature sensor to monitor the temperature variation of the environment, which can provide efficient alarm signals in a hot or cold condition. When attached on person's skin, the ANM displays a unique anti-gravity UWT behavior. The stretchable, wearable and multi-functional nanofibrous composite membrane with an asymmetric wettability shows potential applications in flexible and wearable electronics, health monitoring, etc.

The Combined Effects of the Membrane and Flow Channel Development on the Performance and Energy Footprint of Oil/Water Emulsion Filtration

Membrane filtration is a promising technology for oil/water emulsion filtration due to its excellent removal efficiency of microdroplets of oil in water. However, its performance is highly limited due to the fouling-prone nature of oil droplets on hydrophobic membranes. Membrane filtration typically suffers from a low flux and high pumping energy. This study reports a combined approach to tackling the membrane fouling challenge in oil/water emulsion filtration via a membrane and a flow channel development. Two polysulfone (PSF)-based lab-made membranes, namely PSF- PSF-Nonsolvent induced phase separation (NIPS) and PSF-Vapor-induced phase separation (VIPS), were selected, and the flow channel was modified into a wavy path. They were assessed for the filtration of a synthetic oil/water emulsion. The results showed that the combined membrane and flow channel developments enhanced the clean water permeability with a combined increment of 105%, of which 34% was attributed to the increased effective filtration area due to the wavy flow channel. When evaluated for the filtration of an oil/water emulsion, a 355% permeability increment was achieved from 43 for the PSF-NIPS in the straight flow channel to 198 L m^-2 h^-1 bar^-1 for the PSF-VIPS in the wavy flow channel. This remarkable performance increment was achieved thanks to the antifouling attribute of the developed membrane and enhanced local mixing by the wavy flow channel to limit the membrane fouling. The increase in the filtration performance was translated into up to 78.4% (0.00133 vs. 0.00615 kWh m^-3) lower in pumping energy. The overall findings demonstrate a significant improvement by adopting multi-pronged approaches in tackling the challenge of membrane fouling for oil/water emulsion filtration, suggesting the potential of this approach to be applied for other feeds.

Advances in Asymmetric Wettable Janus Materials for Oil–Water Separation

The frequent occurrence of crude oil spills and the indiscriminate discharge of oily wastewater have caused serious environmental pollution. The existing separation methods have some defects and are not suitable for complex oil–water emulsions. Therefore, the efficient separation of complex oil–water emulsions has been of great interest to researchers. Asymmetric wettable Janus materials, which can efficiently separate complex oil–water emulsions, have attracted widespread attention. This comprehensive review systematically summarizes the research progress of asymmetric wettable Janus materials for oil–water separation in the last decade, and introduces, in detail, the preparation methods of them. Specifically, the latest research results of two-dimensional Janus materials, three-dimensional Janus materials, smart responsive Janus materials, and environmentally friendly Janus materials for oil–water separation are elaborated. Finally, ongoing challenges and outlook for the future research of asymmetric wettable Janus materials are presented.

Facile Fabrication of Superhydrophobic Graphene/Polystyrene Foams for Efficient and Continuous Separation of Immiscible and Emulsified Oil/Water Mixtures

Three-dimensional superhydrophobic/superlipophilic porous materials have attracted widespread attention for use in the separation of oil/water mixtures. However, a simple strategy to prepare superhydrophobic porous materials capable of efficient and continuous separation of immiscible and emulsified oil/water mixtures has not yet been realized. Herein, a superhydrophobic graphene/polystyrene composite material with a micro-nanopore structure was prepared by a single-step reaction through high internal phase emulsion polymerization. Graphene was introduced into the polystyrene-based porous materials to not only enhance the flexibility of the matrix, but also increase the overall hydrophobicity of the composite materials. The resulting as-prepared monoliths had excellent mechanical properties, were superhydrophobic/superoleophilic (water/oil contact angles were 151° and 0°, respectively), and could be used to continuously separate immiscible oil/water mixtures with a separation efficiency that exceeded 99.6%. Due to the size-dependent filtration and the tortuous and lengthy micro-nano permeation paths, our foams were also able to separate surfactant-stabilized water-in-oil microemulsions. This work demonstrates a facile strategy for preparing superhydrophobic foams for the efficient and continuous separation of immiscible and emulsified oil/water mixtures, and the resulting materials have highly promising application potentials in large-scale oily wastewater treatment.

Facile Preparation of Hydrophobic PLA/PBE Micro-Nanofiber Fabrics via the Melt-Blown Process for High-Efficacy Oil/Water Separation

Polylactic acid (PLA) micro-nanofiber fabrics with a large specific surface area and excellent biodegradability are commonly used in oil/water separation; however, challenges remain due to their poor mechanical properties. Herein, a thermoplastic polylactic acid/propylene-based elastomer (PLA/PBE) polymer was prepared by blending PLA with PBE. Then, PLA/PBE micro-nanofiber fabrics were successfully prepared using a melt-blown process. The results show that the PLA/PBE micro-nanofiber fabric has a three-dimensional porous structure, improving the thermal stability and fluidity of the PLA/PBE blended polymers. The PLA/PBE micro-nanofiber fabric demonstrated a significantly reduced average fiber diameter and an enhanced breaking strength. Moreover, the water contact angle of the prepared samples is 134°, which suggests a hydrophobic capacity. The oil absorption rate of the fabric can reach 10.34, demonstrating excellent oil/water separation performance. The successful preparation of PLA/PBE micro-nanofiber fabrics using our new method paves the way for the large-scale production of promising candidates for high-efficacy oil/water separation applications.