1
|
Sabol D, Murčinková Z. Stress Wave Propagation and Decay Based on Micro-Scale Modelling in the Topology of Polymer Composite with Circular Particles. Polymers (Basel) 2024; 16:2189. [PMID: 39125215 PMCID: PMC11314150 DOI: 10.3390/polym16152189] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 06/05/2024] [Revised: 07/22/2024] [Accepted: 07/26/2024] [Indexed: 08/12/2024] Open
Abstract
This article deals with stress wave decay performance, analysing the stress wave propagation generated by an impulsive unit load in a 2D representative unit cell (RUC) of a polymer composite with circular particles representing spherical particles, elliptical particles, and short fibres. The micro-scale numerical simulation uses explicit finite element analysis (FEA). The micro-response to an impulsive unit load creates a stress wave amplitude interacting with the material structure and tends to weaken and absorb energy. The stress wave damping is determined by the decaying amplitudes of Mises stress at the front of the stress wave. The stress wave damping is evaluated for different ratios of tensile modules and material densities of matrix and reinforcing material and other factors, such as percentage and particle size, applied to nine topologies of RUCs, and even the presence of an interfacial region is analysed. Moreover, the article visualises the phases of stress wave decay in various particle distributions, i.e., various topologies. Analysing the different topologies of the same particle volume (area) percentage, the study proved that the composite topology and resulting wave-particle and wave-wave interactions are other sources of material damping. The presence of even a small percentage, 3.5 area%, of reinforcing circular particles in the matrix brings a significant increase in stress wave damping up to about 40-43% (depending on the topology) compared to a homogeneous matrix with stress wave damping of 12.5% under the same conditions. Moreover, the topology with the same volume (area) percentage can increase particle stress wave damping by 15.3%.
Collapse
Affiliation(s)
- Dominik Sabol
- Faculty of Manufacturing Technologies with Seat in Prešov, Technical University of Košice, Bayerova 1, 080 01 Prešov, Slovakia;
| | | |
Collapse
|
2
|
Kumar V, Alam MN, Yewale MA, Park SS. Multifunctional Aspects of Mechanical and Electromechanical Properties of Composites Based on Silicone Rubber for Piezoelectric Energy Harvesting Systems. Polymers (Basel) 2024; 16:2058. [PMID: 39065375 PMCID: PMC11281235 DOI: 10.3390/polym16142058] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 06/27/2024] [Revised: 07/10/2024] [Accepted: 07/17/2024] [Indexed: 07/28/2024] Open
Abstract
Energy harvesting systems fabricated from rubber composite materials are promising due to their ability to produce green energy with no environmental pollution. Thus, the present work investigated energy harvesting through piezoelectricity using rubber composites. These composites were fabricated by mixing titanium carbide (TiC) and molybdenum disulfide (MoS2) as reinforcing and electrically conductive fillers into a silicone rubber matrix. Excellent mechanical and electromechanical properties were produced by these composites. For example, the compressive modulus was 1.55 ± 0.08 MPa (control) and increased to 1.95 ± 0.07 MPa (6 phr or per hundred parts of rubber of TiC) and 2.02 ± 0.09 MPa (6 phr of MoS2). Similarly, the stretchability was 133 ± 7% (control) and increased to 153 ± 9% (6 phr of TiC) and 165 ± 12% (6 phr of MoS2). The reinforcing efficiency (R.E.) and reinforcing factor (R.F.) were also determined theoretically. These results agree well with those of the mechanical property tests and thus validate the experimental work. Finally, the electromechanical tests showed that at 30% strain, the output voltage was 3.5 mV (6 phr of TiC) and 6.7 mV (6 phr of MoS2). Overall, the results show that TiC and MoS2 added to silicone rubber lead to robust and versatile composite materials. These composite materials can be useful in achieving higher energy generation, high stretchability, and optimum stiffness and are in line with existing theoretical models.
Collapse
Affiliation(s)
| | | | | | - Sang-Shin Park
- School of Mechanical Engineering, Yeungnam University, 280 Daehak-Ro, Gyeongsan 38541, Gyeongbuk, Republic of Korea; (V.K.); (M.N.A.); (M.A.Y.)
| |
Collapse
|
3
|
Bokobza L. On the Use of Nanoparticles in Dental Implants. MATERIALS (BASEL, SWITZERLAND) 2024; 17:3191. [PMID: 38998274 PMCID: PMC11242106 DOI: 10.3390/ma17133191] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Received: 04/25/2024] [Revised: 06/16/2024] [Accepted: 06/27/2024] [Indexed: 07/14/2024]
Abstract
Results obtained in physics, chemistry and materials science on nanoparticles have drawn significant interest in the use of nanostructures on dental implants. The main focus concerns nanoscale surface modifications of titanium-based dental implants in order to increase the surface roughness and provide a better bone-implant interfacial area. Surface coatings via the sol-gel process ensure the deposition of a homogeneous layer of nanoparticles or mixtures of nanoparticles on the titanium substrate. Nanotubular structures created on the titanium surface by anodic oxidation yield an interesting nanotopography for drug release. Carbon-based nanomaterials hold great promise in the field of dentistry on account of their outstanding mechanical properties and their structural characteristics. Carbon nanomaterials that include carbon nanotubes, graphene and its derivatives (graphene oxide and graphene quantum dots) can be used as coatings of the implant surface. Their antibacterial properties as well as their ability to be functionalized with adequate chemical groups make them particularly useful for improving biocompatibility and promoting osseointegration. Nevertheless, an evaluation of their possible toxicity is required before being exploited in clinical trials.
Collapse
Affiliation(s)
- Liliane Bokobza
- Independent Researcher, 194-196 Boulevard Bineau, 92200 Neuilly-sur-Seine, France
| |
Collapse
|
4
|
Kumar V, Alam MN, Park SS. Review of Recent Progress on Silicone Rubber Composites for Multifunctional Sensor Systems. Polymers (Basel) 2024; 16:1841. [PMID: 39000697 PMCID: PMC11244113 DOI: 10.3390/polym16131841] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 06/07/2024] [Revised: 06/24/2024] [Accepted: 06/25/2024] [Indexed: 07/17/2024] Open
Abstract
The latest progress (the year 2021-2024) on multifunctional sensors based on silicone rubber is reported. These multifunctional sensors are useful for real-time monitoring through relative resistance, relative current change, and relative capacitance types. The present review contains a brief overview and literature survey on the sensors and their multifunctionalities. This contains an introduction to the different functionalities of these sensors. Following the introduction, the survey on the types of filler or rubber and their fabrication are briefly described. The coming section deals with the fabrication methodology of these composites where the sensors are integrated. The special focus on mechanical and electro-mechanical properties is discussed. Electro-mechanical properties with a special focus on response time, linearity, and gauge factor are reported. The next section of this review reports the filler dispersion and its role in influencing the properties and applications of these sensors. Finally, various types of sensors are briefly reported. These sensors are useful for monitoring human body motions, breathing activity, environment or breathing humidity, organic gas sensing, and, finally, smart textiles. Ultimately, the study summarizes the key takeaway from this review article. These conclusions are focused on the merits and demerits of the sensors and are followed by their future prospects.
Collapse
Affiliation(s)
- Vineet Kumar
- School of Mechanical Engineering, Yeungnam University, 280 Daehak-Ro, Gyeongsan 38541, Gyeongbuk, Republic of Korea
| | - Md Najib Alam
- School of Mechanical Engineering, Yeungnam University, 280 Daehak-Ro, Gyeongsan 38541, Gyeongbuk, Republic of Korea
| | - Sang Shin Park
- School of Mechanical Engineering, Yeungnam University, 280 Daehak-Ro, Gyeongsan 38541, Gyeongbuk, Republic of Korea
| |
Collapse
|
5
|
Ning H, Zhang Y, Lu L, Pan L. Properties and release behavior of sodium alginate-based nanocomposite active films: Effects of particle size of IRMOF-3. Int J Biol Macromol 2024; 271:132488. [PMID: 38763248 DOI: 10.1016/j.ijbiomac.2024.132488] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 02/22/2024] [Revised: 05/05/2024] [Accepted: 05/16/2024] [Indexed: 05/21/2024]
Abstract
Nanoparticles are used as fillers to improve the properties of biopolymers, and their particle size is an important parameter. This work aims to investigate the effect of particle size of isoreticular metal-organic framework-3 (IRMOF-3) on the mechanical, physical, and release properties of sodium alginate (SA)-based composite active film. In our study, IRMOF-3 with six different particle sizes was synthesized by introducing additives. IRMOF-3 loading with carvacrol (IRMOF-3/CA nanoparticles) was incorporated into the SA matrix to prepare the composite film. The characterization and testing results of films showed that the particle size of nanoparticles affected the physical morphology and chemical structure of the film. Especially smaller nanoparticles uniformly dispersed into the SA matrix more easily, forming a denser and more stable spatial network structure with SA, which could more significantly improve the tensile strength, water vapor barrier, and hydrophobic properties of the film (P < 0.05). In addition, the CA release rate from the active film could be significantly reduced by about 33.90 % even when the smallest particle size of the IRMOF-3/CA nanoparticles was added. Therefore, when IRMOF-3/CA is used as the nano-filler to develop SA-based active film, its particle size has a potential influence on the properties of the film.
Collapse
Affiliation(s)
- Haoyue Ning
- Department of Packaging Engineering, Jiangnan University, Wuxi, Jiangsu 214122, China
| | - Yuemei Zhang
- Department of Packaging Engineering, Jiangnan University, Wuxi, Jiangsu 214122, China
| | - Lixin Lu
- Department of Packaging Engineering, Jiangnan University, Wuxi, Jiangsu 214122, China; Jiangsu Key Laboratory of Advanced Food Manufacturing Equipment & Technology, Wuxi, Jiangsu 214122, China.
| | - Liao Pan
- Department of Packaging Engineering, Jiangnan University, Wuxi, Jiangsu 214122, China; Jiangsu Key Laboratory of Advanced Food Manufacturing Equipment & Technology, Wuxi, Jiangsu 214122, China
| |
Collapse
|
6
|
Jantachum P, Phinyocheep P. Compatibilization of Cellulose Nanocrystal-Reinforced Natural Rubber Nanocomposite by Modified Natural Rubber. Polymers (Basel) 2024; 16:363. [PMID: 38337252 DOI: 10.3390/polym16030363] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 11/26/2023] [Revised: 01/15/2024] [Accepted: 01/23/2024] [Indexed: 02/12/2024] Open
Abstract
Due to global warming and environmental concerns, developing a fully bio-based nanocomposite is an attractive issue. In this work, the cellulose nanocrystals (CNCs) extracted from Luffa cylindrica, a renewable resource, were explored as a bio-based reinforcing filler in natural rubber (NR) nanocomposites. In addition, modified natural rubber was explored as a potential compatibilizer to assist the filler dispersion in the rubber nanocomposite. The effect of the CNC content (0-15 phr) on cure characteristics and the mechanical, dynamic, and thermal properties of NR/CNC nanocomposites was investigated. The results showed that the scorch time and cure time of the nanocomposites increased with increased CNC contents. The optimum tensile strength of NR nanocomposites having 5 phr of the CNC (NR-CNC5) was 20.60% higher than the corresponding unfilled NR vulcanizate, which was related to the increased crosslink density of the rubber nanocomposite. The incorporation of oxidized-degraded NR (ODNR) as a compatibilizer in the NR-CNC5 nanocomposite exhibited a considerably reduced cure time, which will lead to energy conservation during production. Moreover, the cure rate index of NR-CNC5-ODNR is much higher than using a petroleum-based silane coupling agent (Si69) as a compatibilizer in the NR-CNC5 nanocomposite. The good filler dispersion in the NR-CNC5 nanocomposite compatibilized by ODNR is comparable to the use of Si69, evidenced by scanning electron microscopy. There is, therefore, a good potential for the use of modified NR as a bio-based compatibilizer for rubber nanocomposites.
Collapse
Affiliation(s)
- Punyarat Jantachum
- Department of Chemistry, Faculty of Science, Mahidol University, Rama VI Rd., Bangkok 10400, Thailand
| | - Pranee Phinyocheep
- Department of Chemistry, Faculty of Science, Mahidol University, Rama VI Rd., Bangkok 10400, Thailand
| |
Collapse
|
7
|
N A, Jakkamputi LP, Gnanasekaran S, Thangamuthu M, Rakkiyannan J, Bhalerao YJ. Dynamic Behavior Modeling of Natural-Rubber/Polybutadiene-Rubber-Based Hybrid Magnetorheological Elastomer Sandwich Composite Structures. Polymers (Basel) 2023; 15:4583. [PMID: 38232007 PMCID: PMC10708534 DOI: 10.3390/polym15234583] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 10/13/2023] [Revised: 11/26/2023] [Accepted: 11/28/2023] [Indexed: 01/19/2024] Open
Abstract
This study investigates the dynamic characteristics of natural rubber (NR)/polybutadiene rubber (PBR)-based hybrid magnetorheological elastomer (MRE) sandwich composite beams through numerical simulations and finite element analysis, employing Reddy's third-order shear deformation theory. Four distinct hybrid MRE sandwich configurations were examined. The validity of finite element simulations was confirmed by comparing them with results from magnetorheological (MR)-fluid-based composites. Further, parametric analysis explored the influence of magnetic field intensity, boundary conditions, ply orientation, and core thickness on beam vibration responses. The results reveal a notable 10.4% enhancement in natural frequencies in SC4-based beams under a 600 mT magnetic field with clamped-free boundary conditions, attributed to the increased PBR content in MR elastomer cores. However, higher magnetic field intensities result in slight frequency decrements due to filler particle agglomeration. Additionally, augmenting magnetic field intensity and magnetorheological content under clamped-free conditions improves the loss factor by from 66% to 136%, presenting promising prospects for advanced applications. This research contributes to a comprehensive understanding of dynamic behavior and performance enhancement in hybrid MRE sandwich composites, with significant implications for engineering applications. Furthermore, this investigation provides valuable insights into the intricate interplay between magnetic field effects, composite architecture, and vibration response.
Collapse
Affiliation(s)
- Ahobal N
- Department of Mechanical Engineering, Dayananda Sagar College of Engineering, Bengaluru 560078, India;
- School of Mechanical Engineering, Vellore Institute of Technology, Chennai 600127, India;
| | | | - Sakthivel Gnanasekaran
- School of Mechanical Engineering, Vellore Institute of Technology, Chennai 600127, India;
| | - Mohanraj Thangamuthu
- Department of Mechanical Engineering, Amrita School of Engineering, Amrita Vishwa Vidyapeetham, Coimbatore 641112, India;
| | | | - Yogesh Jayant Bhalerao
- Department of Mechanical Engineering and Design, School of Engineering, University of East Anglia, Norwich Research Park, Norwich NR47 TIJ, UK;
| |
Collapse
|