Techniques for Interface Stress Measurements within Prosthetic Sockets of Transtibial Amputees: A Review of the Past 50 Years of Research

The AERO prosthetic liner: socket pressure distribution, comfort and material composition

PURPOSE

This study aimed to evaluate the pressure distribution and comfort of transtibial prosthesis wearers using an affordable ethyl-vinyl acetate (EVA) roll-on (AERO) liner.

METHOD

Fifteen unilateral transtibial prosthesis users wore patella tendon bearing (PTB) sockets with a polyethylene foam (PE-lite) liner were enrolled this study. AERO liners were provided to all participants. Six force sensors were applied to the residual limb to evaluate pressure distribution during treadmill walking, and the socket comfort score (SCS) was used to evaluate comfortability. Fourier transform infrared (FT-IR) spectroscopy was performed on the EVA and PE-lite liners.

RESULTS

Eleven participants used prefabricated AERO liners and four participants used custom-made AERO liners. The pressure distribution was analysed by the coefficient of variation (CV): PE-lite was 75.7 ± 6.0 and AERO liner 83.3 ± 4.1. Residual limb pressure was significantly decreased when using the AERO liner (p = .0007), with a large effect size (r = 0.87). Mean SCS was 7.5 ± 1.3 and 8.9 ± 1.1 for PE-lite and AERO liner respectively.

CONCLUSION

Better pressure distribution and comfort were observed when the participants used the AERO liner. AERO had a greater proportion of calcium carbonate (CaCO3). These findings suggest that the AERO liner is a better off-the-shelf option for persons using traditional prosthetic sockets and liners.

Evaluating the Effectiveness of Transtibial Prosthetic Socket Shape Design using Artificial Intelligence: A Clinical Comparison with Traditional Plaster Cast Socket Designs

OBJECTIVE

This study investigates the feasibility of creating an AI algorithm to enhance prosthetic socket shapes for transtibial prostheses, aiming for a less operator-dependent, standardized approach.

DESIGN

The study comprised two phases: first, developing an AI algorithm in a cross-sectional study to predict prosthetic socket shapes. Second, testing the AI-predicted Digitally Measured and Standardized Designed (DMSD-)prosthetic socket against a Manually Measured and Designed (MMD-)prosthetic socket in a two-week within-subject cross-sectional study.

SETTING

The study was done at the rehabilitation department of the Radboud University Medical Center in Nijmegen, the Netherlands.

PARTICIPANTS

The AI algorithm was developed using retrospective data from 116 patients from a Dutch orthopedic company: OIM Orthopedie, and tested on ten randomly selected participants from Papenburg Orthopedie.

INTERVENTIONS

Utilization of an AI algorithm to enhance the shape of a transtibial prosthetic socket.

MAIN OUTCOME MEASURES

The algorithm was optimized to minimize the error in the test set. Participants' Socket Comfort Score (SCS) and fitting ratings from an independent physiotherapist and prosthetist were collected.

RESULTS

Predicted prosthetic shapes deviated by 2.51 mm from the actual designs. 8/10 DMSD and all 10 MMD-prosthetic sockets were satisfactory for home testing. Participants rated DMSD prosthetic sockets at 7.1 ± 2.2 (n=8) and MMD prosthetic sockets at 6.6 ± 1.2 (n=10) on average.

CONCLUSION

The study demonstrates promising results for using an AI algorithm in prosthetic socket design, but long-term effectiveness and refinement for improved comfort and fit in more deviant cases are necessary.

An Optical Sensor for Measuring Displacement between Parallel Surfaces

An optoelectronic sensor was developed to measure the in-plane displacement between two parallel surfaces. This sensor used a photodetector, which was placed on one of the parallel surfaces, to measure the intensity of the red (R), green (G), blue (B), and white/clear (C) light spectra of a broad-spectrum light that was reflected off a color grid on the opposing surface. The in-plane displacement between these two surfaces caused a change in the reflected RGB and C light intensity, allowing the prediction of the displacement direction and magnitude by using a polynomial regression prediction algorithm to convert the RGB and C light intensity to in-plane displacement. Results from benchtop experiments showed that the sensor can achieve accurate displacement predictions with a coefficient of determination R2 > 0.97, a root mean squared error (RMSE) < 0.3 mm, and a mean absolute error (MAE) < 0.36 mm. By measuring the in-plane displacement between two surfaces, this sensor can be applied to measure the shear of a flexible layer, such as a shoe's insole or the lining of a limb prosthesis. This sensor would allow slippage detection in wearable devices such as orthotics, prostheses, and footwear to quantify the overfitting or underfitting of these devices.

Application of ultrasound to monitor in vivo residual bone movement within transtibial prosthetic sockets

Transtibial prosthetic users do often struggle to achieve an optimal prosthetic fit, leading to residual limb pain and stump-socket instability. Prosthetists face challenges in objectively assessing the impact of prosthetic adjustments on residual limb loading. Understanding the mechanical behaviour of the pseudo-joint formed by the residual bone and prosthesis may facilitate prosthetic adjustments and achieving optimal fit. This study aimed to assess the feasibility of using B-mode ultrasound to monitor in vivo residual bone movement within a transtibial prosthetic socket during different stepping tasks. Five transtibial prosthesis users participated, and ultrasound images were captured using a Samsung HM70A system during five dynamic conditions. Bone movement relative to the socket was quantified by tracking the bone contour using Adobe After-Effect. During the study a methodological adjustment was made to improve data quality, and the first two participants were excluded from analysis. The remaining three participants exhibited consistent range of motion, with a signal to noise ratio ranging from 1.12 to 2.59. Medial-lateral and anterior-posterior absolute range of motion varied between 0.03 to 0.88 cm and 0.14 to 0.87 cm, respectively. This study demonstrated that it is feasible to use B-mode ultrasound to monitor in vivo residual bone movement inside an intact prosthetic socket during stepping tasks.

Quantitative analysis of interface pressures in transfemoral prosthetic sockets

BACKGROUND

Among the different factors affecting socket comfort, the pressure applied on residual limb tissues is a crucial parameter for the success or failure of any prosthetic device. However, only a few incomplete data are available on people with transfemoral amputation, in this regard. This work aims at filling this gap in the literature.

METHODS

Ten people with transfemoral amputation wearing 3 different socket designs were recruited in this study: 2 ischial containment sockets featured by proximal trim lines that contain the ischial tuberosity and ramus and greater trochanter, 2 subischial sockets with proximal trim lines under the ischium level, and 6 quadrilateral sockets with proximal trim lines that contain the greater trochanter and create a horizontal seat for the ischial tuberosity. The pressure values at the anterior, lateral, posterior, and medial areas of the socket interface were recorded during 5 locomotion tasks (ie, horizontal, ascent, and descent walking, upstairs and downstairs) by using an F-Socket System (Tekscan Inc., Boston, MA). Gait segmentation was performed by exploiting plantar pressure, which was acquired by an additional sensor under the foot. Mean and standard deviation of minimum and maximum values were calculated for each interface area, locomotion task, and socket design. The mean pressure patterns during different locomotion tasks were reported, as well.

RESULTS

Considering all subjects irrespective of socket design, the mean pressure range resulted 45.3 (posterior)-106.7 (posterior) kPa in horizontal walking; 48.3 (posterior)-113.8 (posterior) kPa in ascent walking; 50.8 (posterior)-105.7 (posterior) kPa in descent walking; 47.9 (posterior)-102.9 (lateral) kPa during upstairs; and 41.8 (posterior)-84.5 (anterior) kPa during downstairs. Qualitative differences in socket designs have been found.

CONCLUSIONS

These data allow for a comprehensive analysis of pressures acting at the tissue-socket interface in people with transfemoral amputation, thus offering essential information for the design of novel solutions or to improve existing ones, in this field.

Soft robotics-inspired sensing system for detecting downward movement and pistoning in prosthetic sockets: A proof-of-concept study

BACKGROUND

Vertical displacement of the residual limb within transtibial prosthetic socket, often known as "pistoning" or downward movement, may lead to skin breakdowns and ulcers. Downward movement is particularly difficult to self-manage for diabetic individuals living with amputation because of diminished sensation in the residual limb from peripheral neuropathy. Therefore, a customizable sensor at the distal end that can alert the users when high-risk downward movement and pistoning occurs is urgently needed.

OBJECTIVES

Presented herein for the first time is a lightweight, inexpensive sensing system inspired by soft robotics that can detect the occurrence and severity of downward movement at the distal end.

METHODS

The sensing system consists of a multilayered torus-shaped balloon, allowing easy integration with pin-lock socket systems. The design allows sensing of vertical displacement without imparting high reaction forces back onto the distal end. A benchtop compression tester was used to characterize system performance. Systematic and parametric benchtop tests were conducted to examine the sensor's physical characteristics. Long-term (24-h) stability of the sensor was also recorded.

RESULTS

Compared with water, air was determined to be a better medium with a higher linear full-scale span (FSS) because of its compressible nature. Repeatable 0.5-mm vertical displacements yielded a linear (>0.99 R2) FSS of 4.5 mm and a sensitivity of 0.8 kPa/mm. The sensing system is highly precise, with as low as 1% FSS total error band and average hysteresis of 2.84% of FSS. Over 24 h, a 4% FSS drift was observed.

CONCLUSION

Sensing system characteristics, coupled with low-cost, customizable fabrication, indicates promising performance for daily use to notify and alert transtibial prosthetic users of downward movement and/or pistoning.

Approach for Non-Intrusive Detection of the Fit of Orthopaedic Devices Based on Vibrational Data

The soft tissues of residual limb amputees are subject to large volume fluctuations over the course of a day. Volume fluctuations in residual limbs can lead to local pressure marks, causing discomfort, pain and rejection of prostheses. Existing methods for measuring interface stress encounter several limitations. A major problem is that the measurement instrumentation is applied in the sensitive interface between the prosthesis and residual limb. This paper presents the principle investigation of a non-intrusive technique to evaluate the fit of orthopaedic prosthesis sockets in transfemoral amputees based on experimentally obtained vibrational data. The proposed approach is based on changes in the dynamical behaviour detectable at the outer surface of prostheses; thus, the described interface is not affected. Based on the experimental investigations shown and the derived results, it can be concluded that structural dynamic measurements are a promising non-intrusive technique to evaluate the fit of orthopaedic prosthesis sockets in transfemoral amputee patients. The obtained resonance frequency changes of 2% are a good indicator of successful applicabilityas these changes can be detected without the need for complex measurement devices.

Advances in the measurement of prosthetic socket interface mechanics: a review of technology, techniques, and a 20-year update

INTRODUCTION

A key determinant of prosthesis use is the quality of fit of the prosthetic socket. The socket surrounds the residual limb and applies the appropriate force distribution to the soft tissues to maintain suspension, support, and stabilization as well as translate limb movement to prosthesis movement. The challenge in socket fabrication lays in achieving geometry that provides the appropriate force distribution at physiologically appropriate locations; a task dependent on the understanding of interface tissue-mechanics.

AREAS COVERED

In the last 20 years substantial advancements in sensor innovation and computational power have allowed researchers to quantify the socket-residual limb interface; this paper reviews prominent measurement and sensing techniques described in literature over this time frame. Advantages and short comings of each technique are discussed with a focus on translation to clinical environments.

EXPERT OPINION

Prosthetic sockets directly influence comfort, device use, user satisfaction, and tissue health. Advancements in instrumentation technology have unlocked the possibility of sophisticated measurement systems providing quantitative data that may work in tandem with a clinician's heuristic expertise during socket fabrication. If validated, many of the emerging sensing technologies could be implemented into a clinical setting to better characterize how patients interact with their device and help inform prosthesis fabrication and assessment techniques.

Overcoming Challenges and Innovations in Orthopedic Prosthesis Design: An Interdisciplinary Perspective

Recent advances in the orthopedic prostheses design have significantly improved the quality of life for individuals with orthopedic disabilities. However, there are still critical challenges that need to be addressed to further enhance the functionality of orthopedic prostheses improving biocompatibility to promote better integration with natural tissues, enhancing durability to withstand the demands of daily use, and improving sensory feedback for better control of movement are the most pressing issues. To address these challenges, promising emerging solutions such as smart prosthetics, 3D printing, regenerative medicine, and artificial intelligence have been developed. These innovative technologies hold the potential to significantly enhance the functionality of orthopedic prostheses. Realizing the full potential of these next-generation orthopedic prostheses requires addressing several critical factors. These include interdisciplinary collaboration between experts in orthopedics, materials science, biology, and engineering, increased investment in research and development, standardization of components to ensure quality and reliability, and improved access to prosthetics. A comprehensive review of these challenges and considerations for future orthopedic prosthesis design is s provided in this paper addressing the further advances to the field. By addressing these issues, we can continue to improve the lives of individuals with orthopedic disabilities and further enhance the field of orthopedic prosthetics.

Scalable approach to fabricate paper-based biomass reduced graphene sensor for the detection of exhaled diabetic breath

Herein, we demonstrate a microwave-assisted chemical reduction technique to exfoliate a few layers of graphene from the natural waste material, 'coconut shell'. The microwave irradiation coconut shell is subjected to structural, morphological and functional groups characterization methods including SEM, Raman, FTIR and XPS spectroscopic analyses. The formation of biomass reduced graphene (BRG) has been confirmed through Raman and FTIR spectroscopic analyzes with the presence of D, G and 2D and other functional spectral bands, respectively. The surface topography of the BRG exhibits two-dimensional mat structures with wrinkle topography, imaged by electron microscopic techniques. The metallic behaviour of the BRG is evaluated by band structure calculation using density functional theory. The synthesized nanostructure has been evaluated for exhaled diabetic breath sensing application by fabricating sensor device on the paper-based substrate by roll-to-roll coating technique. The BRG sensor exhibited enhanced sensing response at a very lower concentration of diabetic biomarker with long term stability and rapid response/recovery time of 1.11 s/41.25 s, respectively. Based on our findings, the microwave-assisted BRG is a potential candidate for fabricating highly scalable, inherently safe, economically viable and excellent sensing performance to detect exhaled diabetic breath at room temperature.

Assessment of Socket Pressure during Walking in Rapid Fit Prosthetic Sockets

(1) Background: A sustainable casting system that combines the use of a polystyrene bag, a prosthetic liner and a vacuum system was developed to reduce fabrication time while maintaining comfort for the trans-tibial prosthesis user. (2) Methods: Eight prosthetists (28.7 ± 8.25 years old) fit ten trans-tibial prosthesis wearers (46 ± 12.4 years old) with two types of total surface bearing (TSB) prostheses; a polystyrene bead (PS) prosthesis and a plaster of paris (POP) prosthesis. Duration of casting and combined mean peak pressure was measured at six locations on the residual limb using Force Sensing Resistors (FSR). A pressure uniformity score (%) was determined. Socket Comfort Scale (SCS) was also measured. (3) Results: Duration of casting for the POP method was 64.8 ± 9.53 min and 7.8 ± 2 min for the PS method, (p = 0.006). Pressure uniformity in the POP prosthesis was 79.3 ± 6.54 and 81.7 ± 5.83 in the PS prosthesis (p = 0.027). SCS in both prosthesis types were equivalent. (4) Conclusion: A rapid fit PS prosthesis was developed, with significantly shorter duration than the traditional POP method. Socket pressure uniformity was confirmed and improved in the PS method. Socket comfort was equal between the two prothesis types.

A case study on the value of in-socket force measurements in gait monitoring of lower-limb prosthesis users

Wearable sensors have the potential to drastically improve gait rehabilitation and assessments. This is especially the case for lower limb prosthesis users as small wearables can provide useful information about in-socket conditions. Through a simple case study, we investigated the value of measuring in-socket forces in addition to gait parameters in gauging the effectiveness of a training intervention. The results showed that the additional objective information obtained through in-socket measurements can enhance our understanding of how a particular intervention affects both gait and socket comfort.

Redundancy Reduction for Sensor Deployment in Prosthetic Socket: A Case Study

The irregular pressure exerted by a prosthetic socket over the residual limb is one of the major factors that cause the discomfort of amputees using artificial limbs. By deploying the wearable sensors inside the socket, the interfacial pressure distribution can be studied to find the active regions and rectify the socket design. In this case study, a clustering-based analysis method is presented to evaluate the density and layout of these sensors, which aims to reduce the local redundancy of the sensor deployment. In particular, a Self-Organizing Map (SOM) and K-means algorithm are employed to find the clustering results of the sensor data, taking the pressure measurement of a predefined sensor placement as the input. Then, one suitable clustering result is selected to detect the layout redundancy from the input area. After that, the Pearson correlation coefficient (PCC) is used as a similarity metric to guide the removal of redundant sensors and generate a new sparser layout. The Jenson-Shannon Divergence (JSD) and the mean pressure are applied as posterior validation metrics that compare the pressure features before and after sensor removal. A case study of a clinical trial with two sensor strips is used to prove the utility of the clustering-based analysis method. The sensors on the posterior and medial regions are suggested to be reduced, and the main pressure features are kept. The proposed method can help sensor designers optimize sensor configurations for intra-socket measurements and thus assist the prosthetists in improving the socket fitting.

HAILO: A Sensorised Hand Splint for the Exploration of Interaction Forces

This study presents the design and development of an instrumented splint for measuring the biomechanical effects of hand splinting, and for assessing interface loading characteristics for people with arthritis. Sixteen multi-axial soft load-sensing nodes were mounted on the splint-skin interface of a custom 3D printed thumb splint. The splint was used to measure the interface forces between splint and hand in 12 healthy participants in 6 everyday tasks. Forces were compared between a baseline relaxed hand position and during states of active use. These data were used to generate a measure of sensor activity across the splint surface. Through direct comparison with a commercial splint, the 3D printed splint was deemed to provide similar levels of support. Observation of the activity across the 16 sensors showed that active areas of the splint surface varied between tasks but were commonly focused at the base of the thumb. Our findings show promise in the ability to detect the changing forces imparted on the hand by the splint surface, objectively characterising their behaviour. This opens the opportunity for future study into the biomechanical effects of splints on arthritic thumbs to improve this important intervention and improve quality of life.

Measuring discomfort-An objective method for quantifying peak pressure discomfort and improved fit in adults with transtibial amputation

BACKGROUND

Prosthetic socket coupling with the residual limb should be comfortable without causing skin breakdown or excessive pressure. However, users report socket discomfort, and there is a scarcity of objective measurements available to assess this feeling of discomfort. Quantifying the specific pressure may enable clinicians and users to determine and improve comfort levels objectively.

OBJECTIVES

(1) To evaluate if a peak pressure reduction assists in resolving wounds, redness, and pain inside prosthetic sockets in people with transtibial amputation. (2) To determine if peak pressures measured inside the prosthetic socket due to external forces could be used to quantify the level of improvement in socket discomfort.

DESIGN

In this cohort study, we used a pressure sensor to quantify and facilitate adjustments to the prosthetic socket, correlating this information to the user's socket comfort.

SETTING

Outpatient clinic in a tertiary hospital in Singapore.

PARTICIPANTS

People (N = 16) with unilateral transtibial lower limb amputation using a prosthesis.

INTERVENTIONS

NA.

MAIN OUTCOME MEASURES

Peak pressure and socket comfort score (SCS).

RESULTS

The peak pressure value showed a statistically significant reduction across all participants following adjustments at a 50% delta change in pressure (p = .001). This was achieved with a mean number of 2.6 ± 1.4 adjustments per participant. Following the adjustments, the paired t-test results showed a mean increase between the first SCS and final SCS was 2.6 (p = .001).

CONCLUSION

The wound, redness, and pain resolved in 15 of 16 participants regardless of diabetic status following socket adjustments. Although the peak pressures values did not correlate to the SCS score, the reduction in peak pressure saw significant improvement to the SCS. The use of a portable sensor is a fast and efficient means to quantify adjustments inside the prosthetic socket and could potentially be considered as part of future care delivery.

A Computational Gait Model With a Below-Knee Amputation and a Semi-Active Variable-Stiffness Foot Prosthesis

INTRODUCTION

Simulations based on computational musculoskeletal models are powerful tools for evaluating the effects of potential biomechanical interventions, such as implementing a novel prosthesis. However, the utility of simulations to evaluate the effects of varied prosthesis design parameters on gait mechanics has not been fully realized due to the lack of a readily-available limb loss-specific gait model and methods for efficiently modeling the energy storage and return dynamics of passive foot prostheses. The purpose of this study was to develop and validate a forward simulation-capable gait model with lower-limb loss and a semi-active variable-stiffness foot (VSF) prosthesis.

METHODS

A seven-segment 28-DoF gait model was developed and forward kinematics simulations, in which experimentally observed joint kinematics were applied and the resulting contact forces under the prosthesis evolved accordingly, were computed for four subjects with unilateral below-knee amputation walking with a VSF.

RESULTS

Model-predicted resultant ground reaction force (GRFR) matched well under trial-specific optimized parameter conditions (mean R2: 0.97, RMSE: 7.7% body weight (BW)) and unoptimized (subject-specific, but not trial-specific) parameter conditions (mean R2: 0.93, RMSE: 12% BW). Simulated anterior-posterior center of pressure demonstrated a mean R2 = 0.64 and RMSE = 14% foot length. Simulated kinematics remained consistent with input data (0.23 deg RMSE, R2 > 0.99) for all conditions.

CONCLUSIONS

These methods may be useful for simulating gait among individuals with lower-limb loss and predicting GRFR arising from gait with novel VSF prostheses. Such data are useful to optimize prosthesis design parameters on a user-specific basis.

A Visual Feedback Tool for Quantitative Pressure Monitoring in Lower-Limb Prosthetic Sockets

Obtaining a good socket fit is an iterative process dependent on the skill and experience of the prosthetist creating it and requires individualisation based on the size and shape. There is no standard measurement system used to aid prosthetic socket creation despite the severe impacts on physical health and quality of life if one is ill fitting. Pressure sensors embedded in a prosthetic socket were used to collect data at the socket–residuum interface. To choose an interpolation method, the sensor array was simplified to a 2D grid with a border for extrapolation and tested using previously collected walking test pressure data. Four multivariable interpolation methods were evaluated to create a colour map of the pressure data. Radial basis function interpolation was chosen, as it produced a clear image with a graduated interpolation between data points, and was used to create a colour map across the surface of a 3D prosthetic socket model. For the model to be accessible to clinical audiences, a desktop application was created using PyQt to view the model. The application allowed for connection to the sensors via Bluetooth, with the pressure data updating on the 3D model in real time. Clinician feedback on the application showed the potential for a clinical product; however, further development informed by feedback from rehabilitation clinicians and prosthesis users is required.

Human-device interface pressure measurement in prosthetic, orthotic and exoskeleton applications: A systematic review

This study aimed to investigate normal and shear load sensor technology that has been characterised and used at the human-device interface in prosthetic, orthotic and exoskeleton applications. In addition to taking a cross-disciplinary view, this study expands on previous reviews by considering recently published papers, clinical translation of sensors, and development of the sensor technology itself. A search of MEDLINE, INSPEC, SCOPUS and Web of Science was performed up to 26 January 2021. A total of 33 studies were assessed for quality and their data extracted. The review found variable quality of published papers, with normal load being most commonly measured, and resistive sensor technology most commonly used. The translation to clinical environments was indicated in most studies, though the study population was not always made up of the target users. Studies could benefit from more direct comparison with clinically relevant load thresholds and by ensuring clinical testing is performed in the most realistic and representative way possible. Additionally, more focus on developing sensors that measure shear loads would enable further insights into conditions at the human-device interface. Finally, all researchers would benefit from better and more widespread anonymous data sharing practices to facilitate further experimentation.

Digital healthcare technologies: Modern tools to transform prosthetic care

INTRODUCTION

Digital healthcare technologies are transforming the face of prosthetic care. Millions of people with limb loss around the world do not have access to any form of rehabilitative healthcare. However, digital technologies provide a promising solution to augment the range and efficiency of prosthetists.

AREAS COVERED

The goal of this review is to introduce the digital technologies that have the potential to change clinical methods in prosthetic healthcare. Our target audience are researchers who are unfamiliar with the field of prostheses in general, especially with the newest technological developments. This review addresses technologies for: scanning of amputated limbs, limb-to-socket rectification, additive manufacturing of prosthetic sockets, and quantifying patient response to wearing sockets. This review does not address biomechatronic prostheses or biomechanical design practices.

EXPERT OPINION

Digital technologies will enable affordable prostheses to be built on a scale larger than with today's clinical practices. Large technological gaps need to be overcome to enable the mass production and distribution of prostheses digitally. However, recent advances in computational methods and CAD/CAM technologies are bridging this gap faster than ever before. We foresee that these technologies will return mobility and economic opportunity to amputees on a global scale in the near future.

Characterising Residual Limb Morphology and Prosthetic Socket Design Based on Expert Clinician Practice

Functional, comfortable prosthetic limbs depend on personalised sockets, currently designed using an iterative, expert-led process, which can be expensive and inconvenient. Computer-aided design and manufacturing (CAD/CAM) offers enhanced repeatability, but far more use could be made from clinicians’ extensive digital design records. Knowledge-based socket design using smart templates could collate successful design features and tailor them to a new patient. Based on 67 residual limb scans and corresponding sockets, this paper develops a method of objectively analysing personalised design approaches by expert prosthetists, using machine learning: principal component analysis (PCA) to extract key categories in anatomic and surgical variation, and k-means clustering to identify local ‘rectification’ design features. Rectification patterns representing Total Surface Bearing and Patella Tendon Bearing design philosophies are identified automatically by PCA, which reveals trends in socket design choice for different limb shapes that match clinical guidelines. Expert design practice is quantified by measuring the size of local rectifications identified by k-means clustering. Implementing smart templates based on these trends requires clinical assessment by prosthetists and does not substitute training. This study provides methods for population-based socket design analysis, and example data, which will support developments in CAD/CAM clinical practice and accuracy of biomechanics research.

Adjustable-Volume Prosthetic Sockets: Market Overview and Value Propositions

The prosthetic socket is commonly considered to be the most important part of the prosthesis and lack of fit can lead to skin breakdown, reduction in wear, reduction in activity, and consequential deleterious health effects. Furthermore, approximately 90% of amputations are due to a vascular etiology, which affect fluid retention regularity, and even small limb volume fluctuations can lead to lack of fit. Adjustability in the socket volume has been suggested as a potential solution to common fit issues but has lacked market penetration mostly due to lack of reimbursement. Despite this there are several adjustable-volume sockets emerging on the market today including prefabricated, modular, custom with adjustable-volume component, custom with adjustable-volume feature, and adjustable-hybrid sockets. Prefabricated sockets are mass produced in common sizes and fit directly to the patient by a prosthetist using pad kits, BOA dials, or straps. Modular sockets are assembled to a patient or model with panels or struts attached to an adjustable base. Custom sockets with adjustable-volume elements are traditionally-fabricated sockets made to a model of a patient's limb with a volume-adjustable component added or volume-adjustable feature built in. Custom-hybrid sockets are made custom to a model of the patient's limb and incorporate several aspects of the previous socket types and include some radically-unique design aspects which cannot be limited to one category. These adjustable-volume sockets offer several advantages to traditional rigid-volume sockets for the patient, prosthetist, and providing clinic. The micro-adjustability for the patient allows them to alter fit without removing the socket, maintaining a more intimate fit throughout the day than traditional sockets. The macro-adjustability for the prosthetist allows for increased options for fit customization including the ability to reverse or undo changes without necessarily re-making the socket. This allows for the most optimal fit for the patient. Adjustable volume also present efficiencies in the fitting process by simplifying or eliminating steps including residual limb shape capture, form modification, diagnostic fabrication, iterative alteration, and definitive fabrication with the different socket types affecting different steps. Due to these factors, adjustable-volume sockets have disrupted the market to the point where reimbursement reform is needed including additional L-codes in the United States and fee-for-service or fee-for-outcome associated with prosthetic follow-up care. Prosthetic care should also be separated from durable medical equipment to allow for alternative reimbursement models. As reimbursement adapts prosthetists must adapt correspondingly to differentiate their skillset from other allied health providers including incorporating more objective methods to show superior care outcomes. This adaptation should include a continued push for state and municipal licensure of prosthetists.

A Scoping Review of Pressure Measurements in Prosthetic Sockets of Transfemoral Amputees during Ambulation: Key Considerations for Sensor Design

Sensor systems to measure pressure at the stump-socket interface of transfemoral amputees are receiving increasing attention as they allow monitoring to evaluate patient comfort and socket fit. However, transfemoral amputees have many unique characteristics, and it is unclear whether existing research on sensor systems take these sufficiently into account or if it is conducted in ways likely to lead to substantial breakthroughs. This investigation addresses these concerns through a scoping review to profile research regarding sensors in transfemoral sockets with the aim of advancing and improving prosthetic socket design, comfort and fit for transfemoral amputees. Publications found from searching four scientific databases were screened, and 17 papers were found relating to the aim of this review. After quality assessment, 12 articles were finally selected for analysis. Three main contributions are provided: a de facto methodology for experimental studies on the implications of intra-socket pressure sensor use for transfemoral amputees; the suggestion that associated sensor design breakthroughs would be more likely if pressure sensors were developed in close combination with other types of sensors and in closer cooperation with those in possession of an in-depth domain knowledge in prosthetics; and that this research would be facilitated by increased interdisciplinary cooperation and open research data generation.

Evaluating the Dynamic Performance of Interfacial Pressure Sensors at a Simulated Body-Device Interface

BACKGROUND

Pressure sensing at the body-device interface can help assess the quality of fit and function of assistive devices during physical activities and movement such as walking and running. However, the dynamic performance of various pressure sensor configurations is not well established.

OBJECTIVES

Two common commercially available thin-film pressure sensors were tested to determine the effects of clinically relevant setup configurations focusing on loading areas, interfacing elements (i.e. 'puck') and calibration methods.

METHODOLOGY

Testing was performed using a customized universal testing machine to simulate dynamic, mobility relevant loads at the body-device interface. Sensor performance was evaluated by analyzing accuracy and hysteresis.

FINDINGS

The results suggest that sensor calibration method has a significant effect on sensor performance although the difference is mitigated by using an elastomeric loading puck. Both sensors exhibited similar performance during dynamic testing that agree with accuracy and hysteresis values reported by manufacturers and in previous studies assessing mainly static and quasi-static conditions.

CONCLUSION

These findings suggest that sensor performance under mobility relevant conditions may be adequately represented via static and quasi-testing testing. This is important since static testing is much easier to apply and reduces the burden on users to verify dynamic performance of sensors prior to clinical application. The authors also recommend using a load puck for dynamic testing conditions to achieve optimal performance.

Investigation of Orthopedic Prosthesis Socket Management after Transfemoral Amputation by Expert Survey

Prosthesis treatment requires the close interaction of different actors. In fitting prostheses to patients, special attention is given to the manufacturing of the socket. The continuous development of the technologies involved in the fitting and optimization of prostheses is shown in the literature. The assessment of orthopedic technicians and their influence in the process is thus far largely unexplored. Ten orthopedic technicians were interviewed about the socket fitting process after transfemoral amputation. The research goal was to clarify the socket treatment process with regards to the German context. The results showed that the orthopedic technicians focussing on the patient during the fitting process. This study underlines the importance of interaction and empathy. Volume fluctuations are decisive within the treatment process and are interactively influenced by various factors. Furthermore, the research emphasizes the need for appropriate assistive technologies and the potential for the further development of existing systems.

Textile-based Pressure Sensors for Monitoring Prosthetic-Socket Interfaces

Amputees are prone to experiencing discomfort when wearing their prosthetic devices. As the amputee population grows this becomes a more prevalent and pressing concern. There is a need for new prosthetic technologies to construct more comfortable and well-fitted liners and sockets. One of the well-recognized impediments to the development of new prosthetic technology is the lack of practical inner socket sensors to monitor the inner socket environment (ISE), or the region between the residual limb and the socket. Here we present a capacitive pressure sensor fabricated through a simple, and scalable sewing process using commercially available conductive yarns and textile materials. This fully-textile sensor provides a soft, flexible, and comfortable sensing system for monitoring the ISE. We provide details of our low-power sensor system capable of high-speed data collection from up to four sensor arrays. Additionally, we demonstrate two custom set-ups to test and validate the textile-based sensors in a simulated prosthetic environment. Finally, we utilize the textile-based sensors to study the ISE of a bilateral transtibial amputee. Results indicate that the textile-based sensors provide a promising potential for seamlessly monitoring the ISE.

Safety Assessment of Rehabilitation Robots: A Review Identifying Safety Skills and Current Knowledge Gaps

The assessment of rehabilitation robot safety is a vital aspect of the development process, which is often experienced as difficult. There are gaps in best practices and knowledge to ensure safe usage of rehabilitation robots. Currently, safety is commonly assessed by monitoring adverse events occurrence. The aim of this article is to explore how safety of rehabilitation robots can be assessed early in the development phase, before they are used with patients. We are suggesting a uniform approach for safety validation of robots closely interacting with humans, based on safety skills and validation protocols. Safety skills are an abstract representation of the ability of a robot to reduce a specific risk or deal with a specific hazard. They can be implemented in various ways, depending on the application requirements, which enables the use of a single safety skill across a wide range of applications and domains. Safety validation protocols have been developed that correspond to these skills and consider domain-specific conditions. This gives robot users and developers concise testing procedures to prove the mechanical safety of their robotic system, even when the applications are in domains with a lack of standards and best practices such as the healthcare domain. Based on knowledge about adverse events occurring in rehabilitation robot use, we identified multi-directional excessive forces on the soft tissue level and musculoskeletal level as most relevant hazards for rehabilitation robots and related them to four safety skills, providing a concrete starting point for safety assessment of rehabilitation robots. We further identified a number of gaps which need to be addressed in the future to pave the way for more comprehensive guidelines for rehabilitation robot safety assessments. Predominantly, besides new developments of safety by design features, there is a strong need for reliable measurement methods as well as acceptable limit values for human-robot interaction forces both on skin and joint level.

A Prosthetic Socket with Active Volume Compensation for Amputated Lower Limb

Typically, the actual volume of the residual limb changes over time. This causes the prosthesis to not fit, and then pain and skin disease. In this study, a prosthetic socket was developed to compensate for the volume change of the residual limb. Using an inflatable air bladder, the proposed socket monitors the pressure in the socket and keeps the pressure distribution uniform and constant while walking. The socket has three air bladders on anterior and posterior tibia areas, a latching type 3-way pneumatic valve and a portable control device. In the paper, the mechanical properties of the air bladder were investigated, and the electromagnetic analysis was performed to design the pneumatic valve. The controller is based on a hysteresis control algorithm with a closed loop, which keeps the pressure in the socket close to the initial set point over a long period of time. In experiments, the proposed prosthesis was tested through the gait simulator that can imitate a human’s gait cycle. The active volume compensation of the socket was successfully verified during repetitive gait cycle using the weight loads of 50, 70, and 90 kg and the residual limb model with a variety of volumes. It was confirmed that the pressure of the residual limb recovered to the initial state through the active control. The pressure inside the socket had a steady state error of less than 0.75% even if the volume of the residual limb was changed from −7% to +7%.

Lower limb prosthetic interfaces: Clinical and technological advancement and potential future direction

The human-prosthesis interface is one of the most complicated challenges facing the field of prosthetics, despite substantive investments in research and development by researchers and clinicians around the world. The journal of the International Society for Prosthetics and Orthotics, Prosthetics and Orthotics International, has contributed substantively to the growing body of knowledge on this topic. In celebrating the 50th anniversary of the International Society for Prosthetics and Orthotics, this narrative review aims to explore how human-prosthesis interfaces have changed over the last five decades; how research has contributed to an understanding of interface mechanics; how clinical practice has been informed as a result; and what might be potential future directions. Studies reporting on comparison, design, manufacturing and evaluation of lower limb prosthetic sockets, and osseointegration were considered. This review demonstrates that, over the last 50 years, clinical research has improved our understanding of socket designs and their effects; however, high-quality research is still needed. In particular, there have been advances in the development of volume and thermal control mechanisms with a few designs having the potential for clinical application. Similarly, advances in sensing technology, soft tissue quantification techniques, computing technology, and additive manufacturing are moving towards enabling automated, data-driven manufacturing of sockets. In people who are unable to use a prosthetic socket, osseointegration provides a functional solution not available 50 years ago. Furthermore, osseointegration has the potential to facilitate neuromuscular integration. Despite these advances, further improvement in mechanical features of implants, and infection control and prevention are needed.

Additive manufacturing techniques for smart prosthetic liners

Elastomeric liners are commonly worn between the prosthetic socket and the limb. A number of improvements to the state of the art of liner technology are required to address outstanding problems. A liner that conforms to the residuum more accurately, may improve the skin health at the stump-socket interface. Previous work has shown that for effective thermal management of the socket environment, an active heat removal system is required, yet this is not available. Volume tracking of the stump could be used as a diagnostic tool for looking at the changes that occur across the day for all users, which depend on activity level, position, and the interaction forces of the prosthetic socket with the limb. We believe that it would be advantageous to embed these devices into a smart liner, which could be replaced and repaired more easily than the highly costly and labour-intensive custom-made socket. This paper presents the work to develop these capabilities in soft material technology, with: the development of a printable nanocomposite stretch sensor system; a low-cost digital method for casting bespoke prosthetic liners; a liner with an embedded stretch sensor for growth / volume tracking; a model liner with an embedded active cooling system.

A personalised prosthetic liner with embedded sensor technology: a case study

BACKGROUND

Numerous sensing techniques have been investigated in an effort to monitor the main parameters influencing the residual limb/prosthesis interface, fundamental to the optimum design of prosthetic socket solutions. Sensing integration within sockets is notoriously complex and can cause user discomfort. A personalised prosthetic liner with embedded sensors could offer a solution. However, to allow for a functional and comfortable instrumented liner, highly customised designs are needed. The aim of this paper is to presents a novel approach to manufacture fully personalised liners using scanned three-dimensional image data of the patient's residual limb, combined with designs that allow for sensor integration. To demonstrate the feasibility of the proposed approach, a personalised liner with embedded temperature and humidity sensors was realised and tested on a transtibial amputee, presented here as a case study.

METHODS

The residual limb of a below knee amputee was first scanned and a three-dimensional digital image created. The output was used to produce a personalised prosthesis. The liner was manufactured using a cryogenic Computer Numeric Control (CNC) machining approach. This method enables fast, direct and precise manufacture of soft elastomer products. Twelve Hygrochron Data Loggers, able to measure both temperature and humidity, were embedded in specific liner locations, ensuring direct sensor-skin contact. The sensor locations were machined directly into the liner, during the manufacturing process. The sensors outputs were assessed on the below amputee who took part in the study, during resting (50 min) and walking activities (30 min). To better describe the relative thermal properties of new liner, the same tests were repeated with the amputee wearing his existing liner. Quantitative comparisons of the thermal properties of the new liner solution with that currently used in clinical practice are, therefore, reported.

RESULTS

The liner machining process took approximately 4 h. Fifteen minutes after donning the prosthesis, the skin temperature reached a plateau. Physical activity rapidly increased residuum skin temperatures, while cessation of activity caused a moderate decrease. Humidity increased throughout the observation period. In addition, the new liner showed better thermal properties with respect to the current liner solution (4% reduction in skin temperature).

CONCLUSIONS

This work describes a personalised liner solution, with embedded temperature and humidity sensors, developed through an innovative approach. This new method allows for a range of sensors to be smoothly embedded into a liner, which is capable of measuring changes in intra-socket microclimate conditions, resulting in the design of advanced socket solutions personalised specifically for individual requirements. In future, this method will not only provide a personalised liner but will also enable dynamic assessment of how a residual limb behaves within the socket during daily activities.

Exploring the role of transtibial prosthetic use in deep tissue injury development: a scoping review

Background

The soft tissue of the residual limb in transtibial prosthetic users encounters unique biomechanical challenges. Although not intended to tolerate high loads and deformation, it becomes a weight-bearing structure within the residuum-prosthesis-complex. Consequently, deep soft tissue layers may be damaged, resulting in Deep Tissue Injury (DTI). Whilst considerable effort has gone into DTI research on immobilised individuals, only little is known about the aetiology and population-specific risk factors in amputees. This scoping review maps out and critically appraises existing research on DTI in lower-limb prosthetic users according to (1) the population-specific aetiology, (2) risk factors, and (3) methodologies to investigate both.

Results

A systematic search within the databases Pubmed, Ovid Excerpta Medica, and Scopus identified 16 English-language studies. The results indicate that prosthetic users may be at risk for DTI during various loading scenarios. This is influenced by individual surgical, morphological, and physiological determinants, as well as the choice of prosthetic componentry. However, methodological limitations, high inter-patient variability, and small sample sizes complicate the interpretation of outcome measures. Additionally, fundamental research on cell and tissue reactions to dynamic loading and on prosthesis-induced alterations of the vascular and lymphatic supply is missing.

Conclusion

We therefore recommend increased interdisciplinary research endeavours with a focus on prosthesis-related experimental design to widen our understanding of DTI. The results have the potential to initiate much-needed clinical advances in surgical and prosthetic practice and inform future pressure ulcer classifications and guidelines.

Developing an Analogue Residual Limb for Comparative DVC Analysis of Transtibial Prosthetic Socket Designs

Personalised prosthetic sockets are fabricated by expert clinicians in a skill- and experience-based process, with research providing tools to support evidence-based practice. We propose that digital volume correlation (DVC) may offer a deeper understanding of load transfer from prosthetic sockets into the residual limb, and tissue injury risk. This study’s aim was to develop a transtibial amputated limb analogue for volumetric strain estimation using DVC, evaluating its ability to distinguish between socket designs. A soft tissue analogue material was developed, comprising silicone elastomer and sand particles as fiducial markers for image correlation. The material was cast to form an analogue residual limb informed by an MRI scan of a person with transtibial amputation, for whom two polymer check sockets were produced by an expert prosthetist. The model was micro-CT scanned according to (i) an unloaded noise study protocol and (ii) a case study comparison between the two socket designs, loaded to represent two-legged stance. The scans were reconstructed to give 108 µm voxels. The DVC noise study indicated a 64 vx subvolume and 50% overlap, giving better than 0.32% strain sensitivity, and ~3.5 mm spatial resolution of strain. Strain fields induced by the loaded sockets indicated tensile, compressive and shear strain magnitudes in the order of 10%, with a high signal:noise ratio enabling distinction between the two socket designs. DVC may not be applicable for socket design in the clinical setting, but does offer critical 3D strain information from which existing in vitro and in silico tools can be compared and validated to support the design and manufacture of prosthetic sockets, and enhance the biomechanical understanding of the load transfer between the limb and the prosthesis.

Sensory neuroprosthesis improves postural stability during Sensory Organization Test in lower-limb amputees

To maintain postural stability, unilateral lower-limb amputees (LLAs) heavily rely on visual and vestibular inputs, and somatosensory cues from their intact leg to compensate for missing somatosensory information from the amputated limb. When any of these resources are compromised, LLAs exhibit poor balance control compared to able-bodied individuals. We hypothesized that restoring somatosensation related to the missing limb via direct activation of the sensory nerves in the residuum would improve the standing stability of LLAs. We developed a closed-loop sensory neuroprosthesis utilizing non-penetrating multi-contact cuff electrodes implanted around the residual nerves to elicit perceptions of the location and intensity of plantar pressures under the prosthetic feet of two transtibial amputees. Effects of the sensory neuroprosthesis on balance were quantified with the Sensory Organization Test and other posturographic measures of sway. In both participants, the sensory neuroprosthesis improved equilibrium and sway when somatosensation from the intact leg and visual inputs were perturbed simultaneously. One participant also showed improvement with the sensory neuroprosthesis whenever somatosensation in the intact leg was compromised via perturbations of the platform. These observations suggest the sensory feedback elicited by neural stimulation can significantly improve the standing stability of LLAs, particularly when other sensory inputs are depleted or otherwise compromised.

Clinical utility of pressure feedback to socket design and fabrication

BACKGROUND

The clinical utility of measuring pressure at the prosthetic socket-residual limb interface is currently unknown.

OBJECTIVES

This study aimed to identify whether measuring interface pressure during prosthetic design and fabrication results in closer agreement in pressure measurements between sockets made by different clinicians, and a reduction in pressure over areas of concern. It also investigated whether clinicians value knowing the interface pressure during the fabrication process.

STUDY DESIGN

Mixed methods.

METHODS

Three prosthetists designed a complete prosthetic system for a transtibial residual limb surrogate. Standardised mechanical testing was performed on each prosthetic system to gain pressure measurements at four key anatomical locations. These measurements were provided to the clinicians, who subsequently modified their sockets as each saw fit. The pressure at each location was re-measured. Each prosthetist completed a survey that evaluated the usefulness of knowing interface pressures during the fabrication process.

RESULTS

Feedback and subsequent socket modifications saw a reduction in the pressure measurements at three of the four anatomical locations. Furthermore, the pressure measurements between prosthetists converged. All three prosthetists found value in the pressure measurement system and felt they would use it clinically.

CONCLUSIONS

Results suggest that sensors measuring pressure at the socket-limb interface has clinical utility in the context of informing prosthetic socket design and fabrication. If the technology is used at the check socket stage, iterative designs with repeated measurements can result in increased consistency between clinicians for the same residual limb, and reductions in the magnitudes of pressures over specific anatomical landmarks.

CLINICAL RELEVANCE

This study provides new information on the value of pressure feedback to the prosthetic socket design process. It shows that with feedback, socket modifications can result in reduced limb pressures, and more consistent pressure distributions between prosthetists. It also justifies the use of pressure feedback in informing clinical decisions.

Investigation of Regression Methods for Reduction of Errors Caused by Bending of FSR-Based Pressure Sensing Systems Used for Prosthetic Applications

The pressure map at the interface of a prosthetic socket and a residual limb contains information that can be used in various prosthetic applications including prosthetic control and prosthetic fitting. The interface pressure is often obtained using force sensitive resistors (FSRs). However, as reported by multiple studies, accuracies of the FSR-based pressure sensing systems decrease when sensors are bent to be positioned on a limb. This study proposes the use of regression-based methods for sensor calibration to address this problem. A sensor matrix was placed in a pressure chamber as the pressure was increased and decreased in a cyclic manner. Sensors’ responses were assessed when the matrix was placed on a flat surface or on one of five curved surfaces with various curvatures. Three regression algorithms, namely linear regression (LR), general regression neural network (GRNN), and random forest (RF), were assessed. GRNN was selected due to its performance. Various error compensation methods using GRNN were investigated and compared to improve instability of sensors’ responses. All methods showed improvements in results compared to the baseline. Developing a different model for each of the curvatures yielded the best results. This study proved the feasibility of using regression-based error compensation methods to improve the accuracy of mapping sensor readings to pressure values. This can improve the overall accuracy of FSR-based sensory systems used in prosthetic applications.

Sensing and actuation technologies for smart socket prostheses

The socket is the most critical part of every lower-limb prosthetic system, since it serves as the interfacial component that connects the residual limb with the artificial system. However, many amputees abandon their socket prostheses due to the high-level of discomfort caused by the poor interaction between the socket and residual limb. In general, socket prosthesis performance is determined by three main factors, namely, residual limb-socket interfacial stress, volume fluctuation of the residual limb, and temperature. This review paper summarizes the various sensing and actuation solutions that have been proposed for improving socket performance and for realizing next-generation socket prostheses. The working principles of different sensors and how they have been tested or used for monitoring the socket interface are discussed. Furthermore, various actuation methods that have been proposed for actively modifying and improving the socket interface are also reviewed. Through the continued development and integration of these sensing and actuation technologies, the long-term vision is to realize smart socket prostheses. Such smart socket systems will not only function as a socket prosthesis but will also be able to sense parameters that cause amputee discomfort and self-adjust to optimize its fit, function, and performance.

Structured multimaterial filaments for 3D printing of optoelectronics

Simultaneous 3D printing of disparate materials; metals, polymers and semiconductors with device quality interfaces and at high resolution remains challenging. Moreover, the precise placement of discrete and continuous domains to enable both device performance and electrical connectivity poses barriers to current high-speed 3D-printing approaches. Here, we report filaments with disparate materials arranged in elaborate microstructures, combined with an external adhesion promoter, to enable a wide range of topological outcomes and device-quality interfaces in 3D printed media. Filaments, structured towards light-detection, are printed into fully-connected 3D serpentine and spherical sensors capable of spatially resolving light at micron resolution across its entire centimeter-scale surface. 0-dimensional metallic microspheres generate light-emitting filaments that are printed into hierarchical 3D objects dotted with electroluminescent pixels at high device resolution of 55 µm not restricted by surface tension effects. Structured multimaterial filaments provides a path towards custom three-dimensional functional devices not realizable by existing approaches.

Evaluating shear and normal force with the use of an instrumented transtibial socket: A case study

Patients with transtibial amputation experience ulcers on their residual limb. The loading between the device and underlying material plays a role in loads transmitted to the skin. The objective was to evaluate normal and shear forces at the socket/liner interface during walking. A 53 year old male (85.45 kg and 177.8 cm) with a transtibial amputation participated in this case study. A transtibial prosthesis was instrumented with a load cell to measure normal and shear forces at the socket interface. Three conditions were evaluated during walking: gel liner, additional three ply sock and a hole in the gel liner. Shear and normal forces were highest with the addition of a three ply. Longitudinal shear stresses ranged from 0.4-7.66 kPa, transverse shear stresses ranged from 0.01-7.79 kPa and normal stresses ranged from 2.7-61.9 kPa. Increased shear and normal forces can cause a significant decrease in blood perfusion, linked to an increased risk of ulcer formation. Experimental force results are also important for future work involving finite element modeling of the skin/liner/device interface.

An Inductive Sensing System to Measure In-Socket Residual Limb Displacements for People Using Lower-Limb Prostheses

The objective of this research was to assess the performance of an embedded sensing system designed to measure the distance between a prosthetic socket wall and residual limb. Low-profile inductive sensors were laminated into prosthetic sockets and flexible ferromagnetic targets were created from elastomeric liners with embedded iron particles for four participants with transtibial amputation. Using insights from sensor performance testing, a novel calibration procedure was developed to quickly and accurately calibrate the multiple embedded sensors. The sensing system was evaluated through laboratory tests in which participants wore sock combinations with three distinct thicknesses and conducted a series of activities including standing, walking, and sitting. When a thicker sock was worn, the limb typically moved further away from the socket and peak-to-peak displacements decreased. However, sensors did not measure equivalent distances or displacements for a given sock combination, which provided information regarding the fit of the socket and how a sock change intervention influenced socket fit. Monitoring of limb⁻socket displacements may serve as a valuable tool for researchers and clinicians to quantitatively assess socket fit.

Stakeholder perspectives for possible residual limb monitoring system for persons with lower-limb amputation

Purpose: To gather ideas from lower-limb prosthesis users and certified prosthetists regarding possible residual limb monitoring system features and data presentation. We also gathered information on the type of residual limb problems typically encountered, how they currently manage those problems, and their ideas for methods to better manage them.Materials and methods: Two focus groups were held; one with certified prosthetists and another with lower-limb prosthesis users. Open-ended questions were used in a moderated discussion that was audio recorded, transcribed, and assessed using applied thematic analysis.Results and conclusions: Seven individuals participated in each focus group. Prosthetists came from a mix of practice settings, while prosthesis users were diverse in level of amputation, aetiology, and years of experience using lower-limb prostheses. Residual limb problems reported by participants were consistent with those in the literature. Participants suggested better managing residual limb problems through improved education, better detection of residual limb problems, and using sensor-based information to improve prosthetic technology. Participants favoured short-term use of a possible residual limb monitoring systems to troubleshoot residual limb problems, with temperature and pressure the most frequently mentioned measurements. Participants described that an ideal residual limb monitoring system would be lightweight, not interfere with prosthesis function, and result in benefits with regard to prosthetic care and socket function that outweighed inconveniences or concerns regarding system use. A potential positive of system use included having objective data for reimbursement justification, although it was pointed out that the residual limb monitoring system itself also needed to be reimbursable.Implications for RehabilitationStakeholders suggested better managing residual limb problems through improved education, better detection of residual limb problems, and using sensor-based information to improve prosthetic technology.Stakeholders favored short-term use of a possible system to troubleshoot residual limb problems, with temperature and pressure the most frequently mentioned measurements.Stakeholders described that an ideal residual limb monitoring system would be lightweight, not interfere with prosthesis function, and result in benefits with regard to prosthetic care and socket function that outweighs any inconveniences or concerns regarding system use.Stakeholders indicated that a potential positive of system use included having objective data for reimbursement justification, although it was pointed out that the residual limb monitoring system itself also needed to be reimbursable.

Management of lower limb amputations

The most common reason for lower limb amputations in the UK is peripheral arterial disease. A thoughtful approach to surgery, with consideration of optimal amputation level and residual limb shape, can improve prosthetic use and functional outcomes. Prosthesis socket design and fit, as well as use of appropriate components, must be considered in accordance with the patient's activity level and potential. Major developments in prosthetics over the past 20 years, particularly in the area of joint design, including microprocessor knees, have increased options to improve ambulation. This is particularly significant among those with more proximal amputations, for whom energy expenditure on walking is even greater. Management of post-amputation pain syndromes including phantom limb pain can prove challenging, although there are novel options for pain control. Long-term care of both the residual and contralateral limbs is paramount to reduce risk of further amputation surgery, and optimize longer term function and quality of life.

Sockets for Limb Prostheses: A Review of Existing Technologies and Open Challenges

In the prosthetics field, one of the most important bottlenecks is still the human-machine interface, namely the socket. Indeed, a large number of amputees still rejects prostheses or points out a low satisfaction level, due to a sub-optimal interaction between the socket and the residual limb tissues. The aim of this paper is to describe the main parameters (displacements, stress, volume fluctuations and temperature) affecting the stump-socket interface and reducing the comfort/stability of limb prostheses. In this review, a classification of the different socket types proposed in the literature is reported, together with an analysis of advantages and disadvantages of the different solutions, from multiple viewpoints. The paper then describes the technological solutions available to face an altered distribution of stresses on the residual limb tissues, volume fluctuations affecting the stump overtime and temperature variations affecting the residual tissues within the socket. The open challenges in this research field are highlighted and the possible future routes are discussed, towards the ambitious objective of achieving an advanced socket able to self-adapt in real-time to the complex interplay of factors affecting the stump, during both static and dynamic tasks.

Optical fiber Bragg grating-instrumented silicone liner for interface pressure measurement within prosthetic sockets of lower-limb amputees

This paper presents a fiber Bragg grating (FBG)-instrumented prosthetic silicone liner that provides cushioning for the residual limb and can successfully measure interface pressures inside prosthetic sockets of lower-limb amputees in a simple and practical means of sensing. The liner is made of two silicone layers between which 12 FBG sensors were embedded at locations of clinical interest. The sensors were then calibrated using a custom calibration platform that mimics a real-life situation. Afterward, a custom gait simulating machine was built to test the liner performance during an amputee's simulated gait. To validate the findings, the results were compared to those obtained by the commonly used F-socket mats. As the statistical findings reveal, both pressure mapping methods measured the interface pressure in a consistent way, with no significant difference (P-values ≥0.05). This pressure mapping technique in the form of a prosthetic liner will allow prosthetics professionals to quickly and accurately create an overall picture of the interface pressure distribution inside sockets in research and clinical settings, thereby improving the socket fit and amputee's satisfaction.

Systematic Review of Studies Examining Transtibial Prosthetic Socket Pressures with Changes in Device Alignment

Suitable lower-limb prosthetic sockets must provide an adequate distribution of the pressures created from standing and ambulation. A systematic search for articles reporting socket pressure changes in response to device alignment perturbation was carried out, identifying 11 studies. These were then evaluated using the American Academy of Orthotists and Prosthetists guidelines for a state-of-the-science review. Each study used a design where participants acted as their own controls. Results were available for 52 individuals and five forms of alignment perturbation. Four studies were rated as having moderate internal and external validity, the remainder were considered to have low validity. Significant limitations in study design, reporting quality and in representation of results and the suitability of calculations of statistical significance were evident across articles. Despite the high inhomogeneity of study designs, moderate evidence supports repeatable changes in pressure distribution for specific induced changes in component alignment. However, there also appears to be a significant individual component to alignment responses. Future studies should aim to include greater detail in the presentation of results to better support later meta-analyses.