Plasmonic Fiber Optic Refractometric Sensors: From Conventional Architectures to Recent Design Trends

Optical fiber biosensors toward in vivo detection

This review takes stock of the various optical fiber-based biosensors that could be used for in vivo applications. We discuss the characteristics that biosensors must have to be suitable for such applications and the corresponding transduction modes. In particular, we focus on optical fiber biosensors based on fluorescence, evanescent wave, plasmonics, interferometry, and Raman phenomenon. The operational principles, implemented solutions, and performances are described and debated. The different sensing configurations, such as the side- and tip-based fiber biosensors, are illustrated, and their adaptation for in vivo measurements is discussed. The required implementation of multiplexed biosensing on optical fibers is shown. In particular, the use of multi-fiber assemblies, one of the most optimal configurations for multiplexed detection, is discussed. Different possibilities for multiple localized functionalizations on optical fibers are presented. A final section is devoted to the practical in vivo use of fiber-based biosensors, covering regulatory, sterilization, and packaging aspects. Finally, the trends and required improvements in this promising and emerging field are analyzed and discussed.

Optrode-Assisted Multiparametric Near-Infrared Spectroscopy for the Analysis of Liquids

We demonstrate a sensing scheme for liquid analytes that integrates multiple optical fiber sensors in a near-infrared spectrometer. With a simple optofluidic method, a broadband radiation is encoded in a time-domain interferogram and distributed to different sensing units that interrogate the sample simultaneously; the spectral readout of each unit is extracted from its output signal by a Fourier transform routine. The proposed method allows performing a multiparametric analysis of liquid samples in a compact setup where the radiation source, measurement units, and spectral readout are all integrated in a robust telecom optical fiber. An experimental validation is provided by combining a plasmonic nanostructured fiber probe and a transmission cuvette in the setup and demonstrating the simultaneous measurement of the absorption spectrum and the refractive index of water-methanol solutions.

Cross-sensitivity immune SPR sensor based on fan-shaped microstructured optical fiber for temperature and refractive index sensing

To avoid coating and filling into the fiber holes, facilitate the phase-matching and eliminate cross-sensitivity problems, we propose a surface plasmon resonance sensor based on a fan-shaped microstructured optical fiber (MOF) for the simultaneous sensing of temperature and refractive index (RI). The fan-shaped structure is fabricated by polishing two sides of MOF with an angle of 120°. One side is coated with the gold film and polydimethylsiloxane layer for temperature sensing, and the other side is only coated with the gold film for RI sensing. The two sensing sides can support resonance peaks with two polarized directions at the angle of 120°, which are independent without cross-sensitivity. By monitoring the shifts of the two polarized peaks, our numerical results show that the temperature sensitivity is 2.932 nm/°C in the range of 30 °C to 40 °C, and RI sensitivity is 4235 nm/RIU in the range of 1.38 to 1.39, respectively.

Analysis of Plasmonic Sensors Performance Realized by Exploiting Different UV-Cured Optical Adhesives Combined with Plastic Optical Fibers

Polymer-based surface plasmon resonance (SPR) sensors can be used to realize simple, small-size, disposable, and low-cost biosensors for application in several fields, e.g., healthcare. The performance of SPR sensors based on optical waveguides can be changed by tuning several parameters, such as the dimensions and the shape of the waveguides, the refractive index of the core, and the metal nanofilms used to excite the SPR phenomenon. In this work, in order to develop, experimentally test, and compare several polymer-based plasmonic sensors, realized by using waveguides with different core refractive indices, optical adhesives and 3D printed blocks with a trench inside have been used. In particular, the sensors are realized by filling the blocks' trenches (with two plastic optical fibers located at the end of these) with different UV-cured optical adhesives and then covering them with the same bilayer to excite the SPR phenomenon. The developed SPR sensors have been characterized by numerical and experimental results. Finally, in order to propose photonic solutions for healthcare, a comparative analysis has been reported to choose the best sensor configuration useful for developing low-cost biosensors.

A Novel Approach to Realize Plasmonic Sensors via Multimode Optical Waveguides: A Review

In recent decades, the Surface Plasmon Resonance (SPR) phenomenon has been utilized as an underlying technique in a broad range of application fields. Herein, a new measuring strategy which harnesses the SPR technique in a way that is different from the classical methodology was explored by taking advantage of the characteristics of multimode waveguides, such as plastic optical fibers (POFs) or hetero-core fibers. The sensor systems based on this innovative sensing approach were designed, fabricated, and investigated to assess their ability to measure various physical features, such as magnetic field, temperature, force, and volume, and to realize chemical sensors. In more detail, a sensitive patch of fiber was used in series with a multimodal waveguide where the SPR took place, to alter the mode profile of the light at the input of the waveguide itself. In fact, when the changes of the physical feature of interest acted on the sensitive patch, a variation of the incident angles of the light launched in the multimodal waveguide occurred, and, as a consequence, a shift in resonance wavelength took place. The proposed approach permitted the separation of the measurand interaction zone and the SPR zone. This meant that the SPR zone could be realized only with a buffer layer and a metallic film, thus optimizing the total thickness of the layers for the best sensitivity, regardless of the measurand type. The proposed review aims to summarize the capabilities of this innovative sensing approach to realize several types of sensors for different application fields, showing the high performances obtained by exploiting a simple production process and an easy experimental setup.

Polymer Doping as a Novel Approach to Improve the Performance of Plasmonic Plastic Optical Fibers Sensors

In this work, Fe2O3 was investigated as a doping agent for poly(methyl methacrylate) (PMMA) in order to enhance the plasmonic effect in sensors based on D-shaped plastic optical fibers (POFs). The doping procedure consists of immerging a premanufactured POF sensor chip in an iron (III) solution, avoiding repolymerization and its related disadvantages. After treatment, a sputtering process was used to deposit a gold nanofilm on the doped PMMA in order to obtain the surface plasmon resonance (SPR). More specifically, the doping procedure increases the refractive index of the POF's PMMA in contact with the gold nanofilm, improving the SPR phenomena. The doping of the PMMA was characterized by different analyses in order to determine the effectiveness of the doping procedure. Moreover, experimental results obtained by exploiting different water-glycerin solutions have been used to test the different SPR responses. The achieved bulk sensitivities confirmed the improvement of the plasmonic phenomenon with respect to a similar sensor configuration based on a not-doped PMMA SPR-POF chip. Finally, doped and non-doped SPR-POF platforms were functionalized with a molecularly imprinted polymer (MIP), specific for the bovine serum albumin (BSA) detection, to obtain dose-response curves. These experimental results confirmed an increase in binding sensitivity for the doped PMMA sensor. Therefore, a lower limit of detection (LOD), equal to 0.04 μM, has been obtained in the case of the doped PMMA sensor when compared to the one calculated for the not-doped sensor configuration equal to about 0.09 μM.

D-shaped fiber optic plasmonic sensors using planar and grating structures of silver and gold: design and analysis

In this paper, a D-shaped optical fiber plasmonic sensor using planar and grating structures of silver and gold metals is simulated using the finite element method under the wave optics module of COMSOL Multiphysics. Performance defining parameters are based on (i) the transmittance curve, viz., resonance wavelength (λ r), shift in resonance wavelength (Δ λ r), minimum transmittance (T m i n ), and bandwidth (BW), and (ii) on electric field distribution of a surface plasmon wave, viz., penetration depth (PD) and propagation length (PL) obtained for the considered sensor structures. It is found that gold gives wider BW than silver (e.g., at 1.39 refractive index of the sample: 480% for the planar case and 241% for the grating case), which deteriorates sensor performance by degrading detection accuracy. However, gold gives higher Δ λ r than silver (at 1.40-1.39=0.01 change in refractive index of the sample: 18.33% for the planar case and 16.39% for the grating case), which improves sensor performance and enhances sensitivity. A grating slightly increases the BW and Δ λ r for both gold and silver. Further, with respect to silver, the sensor that contains gold demonstrates higher PD (e.g., 22.32% at 1.39 refractive index of the sample for the planar case) and lower PL (e.g., 22.74% at 1.39 refractive index of sample for the planar case). A grating increases the PD (e.g., 10% for silver at 1.39 refractive index of the sample), whereas it decreases the PL (e.g., 8.73% for silver at 1.39 refractive index of the sample). Lower PL signifies the localization of the field, whereas higher PD enables the sensor to detect larger molecules. Therefore, the sensor with grating metals provides better sensitivity with reduced detection accuracy for the detection of comparatively larger molecules.

Estradiol Detection for Aquaculture Exploiting Plasmonic Spoon-Shaped Biosensors

In this work, a surface plasmon resonance (SPR) biosensor based on a spoon-shaped waveguide combined with an estrogen receptor (ERα) was developed and characterized for the detection and the quantification of estradiol in real water samples. The fabrication process for realizing the SPR platform required a single step consisting of metal deposition on the surface of a polystyrene spoon-shaped waveguide featuring a built-in measuring cell. The biosensor was achieved by functionalizing the bowl sensitive surface with a specific estrogen receptor (ERα) that was able to bind the estradiol. In a first phase, the biosensor tests were performed in a phosphate buffer solution obtaining a limit of detection (LOD) equal to 0.1 pM. Then, in order to evaluate the biosensor's response in different real matrices related to aquaculture, its performances were examined in seawater and freshwater. The experimental results support the possibility of using the ERα-based biosensor for the screening of estradiol in both matrices.

Plasmonic biosensing with tilted fiber Bragg gratings interrogated using a 512-pixel spectrometer

Plasmonic tilted fiber Bragg gratings (TFBGs) are very efficient for fast, accurate, and minimally invasive biosensing. Their transmitted amplitude spectrum is a dense comb of narrowband cladding mode resonances (full width at half maximum < 1 nm) that is usually demodulated using highly resolved (wavelength resolution < 10 pm) devices. This work demonstrates the possibility of using a coarsely resolved spectrometer (166 pm) to read out the amplitude spectrum of a gold-coated TFBG. A refined analysis of the spectral content has allowed us to develop signal processing that provides a refractometric sensitivity of 2656 nm/RIU. This is a fivefold improvement compared to previously reported read-out techniques. Biosensing has then been successfully implemented with gold-coated TFBGs implemented in reflection mode for the detection of insulin, with specific antibodies grafted on the gold surface. Our experimental work is a first step toward the industrialization of the FBG technology, as it opens the door to fast parallel biosensing, profiting from the multiple sensing channels (up to 64) of the interrogator and its high processing speed (repetition rate up to 3 kHz).

Plasmonic Sensors beyond the Phase Matching Condition: A Simplified Approach

The conventional approach to optimising plasmonic sensors is typically based entirely on ensuring phase matching between the excitation wave and the surface plasmon supported by the metallic structure. However, this leads to suboptimal performance, even in the simplest sensor configuration based on the Otto geometry. We present a simplified coupled mode theory approach for evaluating and optimizing the sensing properties of plasmonic waveguide refractive index sensors. It only requires the calculation of propagation constants, without the need for calculating mode overlap integrals. We apply our method by evaluating the wavelength-, device length- and refractive index-dependent transmission spectra for an example silicon-on-insulator-based sensor of finite length. This reveals all salient spectral features which are consistent with full-field finite element calculations. This work provides a rapid and convenient framework for designing dielectric-plasmonic sensor prototypes-its applicability to the case of fibre plasmonic sensors is also discussed.

Plasmonic optical fiber gratings based on few-layer Ta2C MXenes for refractive index sensing

Tilted fiber Bragg grating (TFBG) is a widespread approach for developing refractive index (RI) sensors. The unique optoelectronic properties exhibited by MXene are expected to enhance the performance of TFBG-SPR sensors. In this study, a Ta₂C coating appropriate for sensing was obtained by optimizing the photo-deposition time, which addressed the challenge of preparing large areas of MXene. The uniform coating of the few-layer Ta₂C increases the wavelength sensitivity and FOM of the sensor to 229.5 nm/RIU and 2228.15 respectively. This significant enhancement was attributed to an ordered MXene phase of the grown Ta₂C. The energy band theory verified the metallic nature of the Ta₂C and the amplification effect on the RI response. Finite element analysis demonstrated that the stronger absorption band of Ta₂C facilitated the generation of surface plasmon polariton. Based on the above benefits, the sensor detected melamine in milk with a detection limit of 7.9 × 10^-9M. The TFBG/Au/Ta₂C sensor is a promising approach for biochemical analysis and trace detection.

Flat Photonic Crystal Fiber Plasmonic Sensor for Simultaneous Measurement of Temperature and Refractive Index with High Sensitivity

A compact temperature-refractive index (RI) flat photonic crystal fiber (PCF) sensor based on surface plasmon resonance (SPR) is presented in this paper. Sensing of temperature and RI takes place in the x- and y- polarization, respectively, to avoid the sensing crossover, eliminating the need for matrix calculation. Simultaneous detection of dual parameters can be implemented by monitoring the loss spectrum of core modes in two polarizations. Compared with the reported multi-function sensors, the designed PCF sensor provides higher sensitivities for both RI and temperature detection. A maximum wavelength sensitivity of -5 nm/°C is achieved in the temperature range of -30-40 °C. An excellent optimal wavelength sensitivity of 17,000 nm/RIU is accomplished in the RI range of 1.32-1.41. The best amplitude sensitivity of RI is up to 354.39 RIU^-1. The resolution of RI and temperature sensing is 5.88 × 10^-6 RIU and 0.02 °C, respectively. The highest value of the figure of merit (FOM) is 216.74 RIU^-1. In addition, the flat polishing area of the gold layer reduces the manufacturing difficulty. The proposed sensor has the characteristics of high sensitivity, simple structure, good fabrication repeatability, and flexible operation. It has potential in medical diagnosis, chemical inspection, and many other fields.

Optical Properties of a Tapered Optical Fiber Coated with Alkanes Doped with Fe3O4 Nanoparticles

The presented research shows the possibilities of creating in-line magnetic sensors based on the detection of changes of light propagation parameters, especially polarization, obtained by mixing Fe₃O₄ nanoparticles with hexadecane (higher alkane) surrounding a biconical optical fiber taper. The fiber optic taper allows to directly influence light parameters inside the taper without the necessity to lead the beam out of the structure. The mixture of hexadecane and Fe₃O₄ nanoparticles forms a special cladding surrounding a fiber taper which can be controlled by external factors such as the magnetic field. Described studies show changes of transmission (power, loss) and polarization properties like azimuth, and ellipticity, depending on the location of the mixture on sections of tapered optical fiber. The taper was made of a standard single-mode telecommunication fiber, stretched out to a length of 20.0 ± 0.5 mm and the diameter of the tapers is around 15.0 ± 0.3 μm, with the loss lower than 0.5 dB @ 1550 nm. Such a taper causes the beam to leak out of the waist structure and allows the addition of the external beam-controlling cladding material. The presented research can be used to build polarization switches or optical sensor. The results show that it can be a new way to control the propagation parameters of a light beam using tapered optical fiber and magnetic mixture.

SPR Sensor Based on a Tapered Optical Fiber with a Low Refractive Index Liquid Crystal Cladding and Bimetallic Ag-Au Layers

This paper presents a study of the influence of bimetallic layer covers of a tapered optical fiber surrounded by a low refractive index liquid crystal on the properties of light propagation in the taper structure. This research follows previous works on the effect of monometallic thin films (Au and Ag). In this case, the total thicknesses of the bimetallic layers were h = 10 nm, and the participation of gold and silver was equal. The films were deposited on one side of the tapered waist area. The liquid crystal cells were controlled with a voltage U from 0 to 200 V, with and without amplitude modulation at a frequency of fmod = 5 Hz. For the purposes of this research, spectral characteristics were obtained for a wavelength λ ranging from 550 to 1200 nm. Measurements were carried out at room temperature for three types of rubbed layers orientation-orthogonal, parallel, and twist in relation to the fiber axis. Obtained resonant peaks were compared with the previous results regarding the resonant wavelength, peak width, SNR, and maximum absorption. In the presented paper, the novelty is mainly focused on the materials used and their time stability, as well as corresponding changes in the technological parameters used.

Spoon-shaped polymer waveguides to excite multiple plasmonic phenomena: A multisensor based on antibody and molecularly imprinted nanoparticles to detect albumin concentrations over eight orders of magnitude

A polymeric multimode waveguide, characterized by a pioneering spoon-shaped geometry, was herein proposed for the first time to devise Surface Plasmon Resonance (SPR) biochemical sensors. The plasmon excitation was enabled by layering a gold nanofilm of ∼60 nm onto the spoon-waveguide. As a consequence of the waveguide's extra-ordinary geometry, two distinct sensing regions were identified: a planar one, located on the spoon's neck, and a concave one on the bowl, with angled surfaces. The bulk sensitivity (S_n) is correlated both to the way the light was launched in/collected from the sensor (parallel or orthogonal to the main axis of the waveguide) and to the sensing area interrogated (planar-neck or angled-bowl), indicating that the sensor's performance can be conveniently tuned, depending on the chosen measuring configuration. The SPR sensor's characterization showed S_n equal to 750 nm/RIU for the neck and to 950 nm/RIU for the bowl. To further inspect the peculiar sensing-features and assess the application niches, the spoon-shaped waveguide was functionalized with two kinds of receptors, both specific for human serum albumin (HSA): an antibody on the bowl region (high S_n); molecularly imprinted nanoparticles (nanoMIPs) on the neck region (low S_n). The experimental results showed a limit of detection (LOD) for the immune-sensor of 280 pM and an LOD for the nanoMIP-sensor of 4.16 fM. The overall response of the HSA multi-sensor encompassed eight orders of magnitude, suggesting that the spoon-shaped waveguide's provides multi-scale detection and holds potential to devise multi-analyte sensing platforms.

Biomechanical Sensing Using Gas Bubbles Oscillations in Liquids and Adjacent Technologies: Theory and Practical Applications

Gas bubbles present in liquids underpin many natural phenomena and human-developed technologies that improve the quality of life. Since all living organisms are predominantly made of water, they may also contain bubbles-introduced both naturally and artificially-that can serve as biomechanical sensors operating in hard-to-reach places inside a living body and emitting signals that can be detected by common equipment used in ultrasound and photoacoustic imaging procedures. This kind of biosensor is the focus of the present article, where we critically review the emergent sensing technologies based on acoustically driven oscillations of bubbles in liquids and bodily fluids. This review is intended for a broad biosensing community and transdisciplinary researchers translating novel ideas from theory to experiment and then to practice. To this end, all discussions in this review are written in a language that is accessible to non-experts in specific fields of acoustics, fluid dynamics and acousto-optics.

Dual-channel temperature-compensated vector magnetic field sensor based on lab-on-a-fiber-tip

Fiber-optic magnetic field sensors based on magnetic fluid (MF) is encountering with thermal effects and demand for vectorization for several years. A common solution is to use axially processed fiber cascaded with fiber Bragg grating (FBG). However, the length of such sensors is usually in centimeter-level, which restricts the sensing applications in narrow space and gradient field cases. In this work, we present an ultracompact reflection-type dual-channel sensor for vector magnetic field (Channel 1, referred as CH1) and temperature (Channel 2, referred as CH2) monitoring, which is composed of a pair of gold-plated wedge-shaped multimode fiber (MMF) tip and gold-plated multimode-no-core fiber (MNF) tip. The surface plasmon resonance (SPR) effect was adopted. The two sensor probes are coated with magnetic-field-sensitive MF and temperature-sensitive polydimethylsiloxane (PDMS), respectively. The issue of vector magnetic field and temperature cross-sensitivity is tactfully resolved. Importantly, the proposed sensing probes are ultracompact and the spatial resolution is extremely small (615 µm for CH1 based on wedge-shaped fiber tip and 2 mm for CH2 based on MNF), which is very helpful for narrow space and gradient magnetic field detection. The obtained magnetic field intensity sensitivities are 1.10 nm/mT (90° direction) and -0.26 nm/mT (0° direction), and temperature sensitivity is -3.12 nm/°C.

A method for the controllable fabrication of optical fiber-based localized surface plasmon resonance sensors

Optical fiber-based Localized Surface Plasmon Resonance (OF-LSPR) biosensors have emerged as an ultra-sensitive miniaturized tool for a great variety of applications. Their fabrication by the chemical immobilization of gold nanoparticles (AuNPs) on the optic fiber end face is a simple and versatile method. However, it can render poor reproducibility given the number of parameters that influence the binding of the AuNPs. In order to develop a method to obtain OF-LSPR sensors with high reproducibility, we studied the effect that factors such as temperature, AuNPs concentration, fiber core size and time of immersion had on the number and aggregation of AuNPs on the surface of the fibers and their resonance signal. Our method consisted in controlling the deposition of a determined AuNPs density on the tip of the fiber by measuring its LSPR signal (or plasmonic signal, Sp) in real-time. Sensors created thus were used to measure changes in the refractive index of their surroundings and the results showed that, as the number of AuNPs on the probes increased, the changes in the Sp maximum values were ever lower but the wavelength shifts were higher. These results highlighted the relevance of controlling the relationship between the sensor composition and its performance.

High Birefringence D-Shaped Germanium-Doped Photonic Crystal Fiber Sensor

In this work, a surface plasmon resonance (SPR) sensor based on a D-shaped germanium-doped photonic crystal fiber (PCF) is proposed. The finite element method (FEM) is introduced to analyze the structure parameters, such as germanium-doped concentration, lattice pitch, and air hole size. In addition, the coupling properties and birefringence properties of PCF are also studied. The computer simulation results indicate that two different surface plasmon polariton (SPP) coupling modes are produced on the polished surface, covered with metal film, when the analyte refractive index (RI) is 1.34. Then, with the increase of the RI, the incompleteness of one of the coupling modes will be transformed into the complete coupling. The effect of germanium concentration on the birefringence is also analyzed. It has an optimal wavelength sensitivity of 5600 nm/RIU when the RI is 1.37. This sensor exhibits a maximum birefringence of 1.06 × 10-2 and a resolution of 1.78 × 10-5 RIU with high linearity.

A Plasmonic Biosensor Based on Light-Diffusing Fibers Functionalized with Molecularly Imprinted Nanoparticles for Ultralow Sensing of Proteins

Plasmonic bio/chemical sensing based on optical fibers combined with molecularly imprinted nanoparticles (nanoMIPs), which are polymeric receptors prepared by a template-assisted synthesis, has been demonstrated as a powerful method to attain ultra-low detection limits, particularly when exploiting soft nanoMIPs, which are known to deform upon analyte binding. This work presents the development of a surface plasmon resonance (SPR) sensor in silica light-diffusing fibers (LDFs) functionalized with a specific nanoMIP receptor, entailed for the recognition of the protein human serum transferrin (HTR). Despite their great versatility, to date only SPR-LFDs functionalized with antibodies have been reported. Here, the innovative combination of an SPR-LFD platform and nanoMIPs led to the development of a sensor with an ultra-low limit of detection (LOD), equal to about 4 fM, and selective for its target analyte HTR. It is worth noting that the SPR-LDF-nanoMIP sensor was mounted within a specially designed 3D-printed holder yielding a measurement cell suitable for a rapid and reliable setup, and easy for the scaling up of the measurements. Moreover, the fabrication process to realize the SPR platform is minimal, requiring only a metal deposition step.

Development of a surface plasmon resonance sensor using an optical fiber prepared by electroless displacement gold plating and its application to immunoassay

A simple and low-cost method of fabricating an optical fiber for a surface plasmon resonance (SPR) sensor was proposed. The method is based on the electroless nickel plating and subsequent displacement gold plating of the core of the optical fiber. The thickness of the nickel and gold thin films deposited on the core of the optical fiber could be controlled by measuring the reflected light intensity from the tip of the optical fiber during the plating processes. The sensitivity and resolution of the SPR sensor with the fabricated optical fiber in the refractive index range from 1.333 to 1.348 were 1324.3 nm/RIU and 7.6 × 10^-4 RIU, respectively. The developed SPR sensor was successfully used in the determination of immunoglobulin A (IgA) in human saliva. The IgA quantification results obtained by the SPR sensor were in excellent agreement with those obtained by conventional enzyme-linked immunosorbent assay using a 96-well microtiter plate.

Enhancement of the SPR Effect in an Optical Fiber Device Utilizing a Thin Ag Layer and a 3092A Liquid Crystal Mixture

This paper is a continuation of previous work and shows the enhancement of the surface plasmon resonance effect in a tapered optical fiber device. The study investigated liquid crystal cells containing a tapered optical fiber covered with a silver nanolayer, surrounded by a low refractive index liquid crystal in terms of the properties of light propagation in the taper structure. Silver films with a thickness of d = 10 nm were deposited on the tapered waist area. Measurements were performed at room temperature; liquid crystal steering voltage U from 0 to 200 V, with and without any amplitude modulation with a frequency of f = 5 Hz, and the wavelength λ ranged from 550 to 1200 nm. A significant influence of the initial arrangement of liquid crystals molecules on light propagation was observed. Three types of liquid crystal cells—orthogonal, parallel, and twist—were considered. During the measurements, resonant peaks were obtained—the position of which can also be controlled by the type of liquid crystal cells and the steering voltage. Based on the obtained results, the best parameters, such as highest peak’s width reduction, and the highest SNR value were received for twisted cells. In addition, the present work was compared with the previous work and showed the possibility of improving properties of the manufactured probes, and consequently, the surface plasmon resonance effect. In the presented paper, the novelty is mainly focused on the used materials as well as suitable changes in applied technological parameters. In contrast to gold, silver is characterized by different optic and dielectric properties, e.g., refractive index, extension coefficient, and permittivity, which results in changes in the light propagation and the SPR wavelengths.

Differential Refractive Index Sensor Based on Coupled Plasmon Waveguide Resonance in the C-Band

We proposed a differential fiber-optic refractive index sensor based on coupled plasmon waveguide resonance (CPWR) in the C-band. The sensor head is a BK7 prism coated with ITO/Au/ITO/TiO₂ film. CPWR is excited on the film by the S-polarized components of an incident light. The narrow absorption peak of CPWR makes it possible to realize dual-wavelength differential intensity (DI) interrogation by using only one incident point. To implement DI interrogation, we used a DWDM component to sample the lights with central wavelengths of 1529.55 and 1561.42 nm from the lights reflected back by the sensor head. The intensities of the dual-wavelength lights varied oppositely within the measurement range of refractive index, thus, a steep slope was produced as the refractive index of the sample increased. The experimental results show that the sensitivity is 32.15/RIUs within the measurement range from 1.3584 to 1.3689 and the resolution reaches 9.3 × 10⁻⁶ RIUs. Benefiting from the single incident point scheme, the proposed sensor would be easier to calibrate in bio-chemical sensing applications. Moreover, this sensing method is expected to be applied to retro-reflecting SPR sensors with tapered fiber tip to achieve better resolution than wavelength interrogation.

A High-Sensitivity SPR Refractive Index Sensor Based on No-Core Fiber with Ag-Cu Composite Films

A fiber/Ag-Cu films surface plasmon resonance (SPR) refractive index (RI) sensor composed of multimode fiber-no-core-fiber-multimode fiber (MMF-NCF-MMF) structure is designed. The sensing region length and Cu film deposition time of sensor are gradually optimized by the control variable method, which finally achieves the improvement of sensor properties. We experimentally compared the sensing performance of the fiber/Ag film and fiber/Ag-Cu films sensor. Experimental results show that the fiber/Ag-Cu films sensor has good linearity (R-square = 0.993), and its sensitivity is as high as 3957 nm/RIU in the refractive index detection range of 1.3328–1.3853, which is 1109 nm/RIU higher than the sensitivity of a conventional fiber/Ag film sensor. The sensor presented in this paper adopts the structure with composite metal film, which outperforms the common single-layer metal film in chemical stability such as oxidation resistance and mechanical hardness. Meanwhile, the SPR sensor with MMF-NCF-MMF structure has the advantages of convenient manufacture and compact structure. In conclusion, it can bestow a unique advantage in the field of biological detection or chemical analysis.

The Role of Tapered Light-Diffusing Fibers in Plasmonic Sensor Configurations

In this work, we experimentally analyzed the effect of tapering in light-diffusing optical fibers (LDFs) when employed as surface plasmon resonance (SPR)-based sensors. Although tapering is commonly adopted to enhance the performance of plasmonic optical fiber sensors, we have demonstrated that in the case of plasmonic sensors based on LDFs, the tapering produces a significant worsening of the bulk sensitivity (roughly 60% in the worst case), against a slight decrease in the full width at half maximum (FWHM) of the SPR spectra. Furthermore, we have demonstrated that these aspects become more pronounced when the taper ratio increases. Secondly, we have established that a possible alternative exists in using the tapered LDF as a modal filter after the sensible region. In such a case, we have determined that a good trade-off between the loss in sensitivity and the FWHM decrease could be reached.

Bovine Serum Albumin Protein Detection by a Removable SPR Chip Combined with a Specific MIP Receptor

Nowadays, the development of simple, fast, and low-cost selective sensors to detect substances of interest is of great importance in several application fields. Among this kind of sensors, those based on surface plasmon resonance (SPR) represent a promising category, since they are highly sensitive, versatile, and label-free. In this work, an SPR probe, based on a poly(methyl methacrylate) (PMMA) slab waveguide covered by a gold nanofilm, combined with a specific molecularly imprinted polymer (MIP) receptor for bovine serum albumin (BSA) protein, has been realized and experimentally characterized. The obtained experimental results have shown a limit of detection (LOD) equal to about 8.5 × 10−9 M. This value is smaller than the one achieved by another SPR probe, based on a D-shaped plastic optical fiber (POF), functionalized with the same MIP receptor; more specifically, the obtained LOD was reduced by about three orders of magnitude with respect to the POF configuration. Moreover, concerning the D-shaped POF configuration, no manufacturing process is present in the proposed sensor configuration. In addition, fibers are used only to connect the simple sensor chip with a light source and a detector, promoting a bio-chemical sensing approach based on disposable, low-cost, and removable chips.

Surface Plasmonic Sensors: Sensing Mechanism and Recent Applications

Surface plasmonic sensors have been widely used in biology, chemistry, and environment monitoring. These sensors exhibit extraordinary sensitivity based on surface plasmon resonance (SPR) or localized surface plasmon resonance (LSPR) effects, and they have found commercial applications. In this review, we present recent progress in the field of surface plasmonic sensors, mainly in the configurations of planar metastructures and optical-fiber waveguides. In the metastructure platform, the optical sensors based on LSPR, hyperbolic dispersion, Fano resonance, and two-dimensional (2D) materials integration are introduced. The optical-fiber sensors integrated with LSPR/SPR structures and 2D materials are summarized. We also introduce the recent advances in quantum plasmonic sensing beyond the classical shot noise limit. The challenges and opportunities in this field are discussed.

An Overview of Artificial Olfaction Systems with a Focus on Surface Plasmon Resonance for the Analysis of Volatile Organic Compounds

The last three decades have witnessed an increasing demand for novel analytical tools for the analysis of gases including odorants and volatile organic compounds (VOCs) in various domains. Traditional techniques such as gas chromatography coupled with mass spectrometry, although very efficient, present several drawbacks. Such a context has incited the research and industrial communities to work on the development of alternative technologies such as artificial olfaction systems, including gas sensors, olfactory biosensors and electronic noses (eNs). A wide variety of these systems have been designed using chemiresistive, electrochemical, acoustic or optical transducers. Among optical transduction systems, surface plasmon resonance (SPR) has been extensively studied thanks to its attractive features (high sensitivity, label free, real-time measurements). In this paper, we present an overview of the advances in the development of artificial olfaction systems with a focus on their development based on propagating SPR with different coupling configurations, including prism coupler, wave guide, and grating.

IP-Dip-Based SPR Structure for Refractive Index Sensing of Liquid Analytes

In this paper, we present a two-dimensional surface plasmon resonance structure for refractive index sensing of liquid analytes. The polymer structure was designed with a period of 500 nm and prepared in a novel IP-Dip polymer by direct laser writing lithography based on a mechanism of two-photon absorption. The sample with a set of prepared IP-Dip structures was coated by 40 nm thin gold layer. The sample was encapsulated into a prototyped chip with inlet and outlet. The sensing properties were investigated by angular measurement using the prepared solutions of isopropyl alcohol in deionized water of different concentrations. Sensitivity of 478-617 nm per refractive index unit was achieved in angular arrangement at external angle of incidence of 20°.

Simply and cost-effectively fabricated AuNP-based fusion spliced transmissive optical fiber LSPR probes

The transmissive optical fiber localized surface plasmon resonance (LSPR) sensor has become an effective tool in refractive index sensing because of its compact structure, high sensitivity and strong designability. However, its special structure with the sensing region in the middle of the optical fiber leads to the shortcomings of difficult preparation and poor reproducibility, which greatly restricts its application scopes. In order to solve such problem, we design gold nanoparticle (AuNP)-based fusion spliced transmissive optical fiber LSPR probes, which are fabricated via the fusion splicing between the surface modified combination tapered optical fiber and another multimode quartz optical fiber but are totally different from other fabrications of the reported transmissive optical fiber LSPR probes. The fiber probe fabrication is rather simple and cost-effective, only relying on the procedures of combination tapered optical fiber preparation, surface modification and probe fusion splicing, and except for the probe fusion splicing, the other procedures can be mass prepared thus maintaining high efficiency and good reproducibility in fiber probe fabrications. Moreover, according to the experimental verifications, the proposed fiber probes can reach rather high sensitivity in refractive index sensing with high accuracy and good stability in both static and dynamic detecting modes. Therefore, the AuNP-based fusion spliced transmissive optical fiber LSPR probe is a preferred solution for refractive index sensing and can be widely used in various applications.

Composite Structure Based on Gold-Nanoparticle Layer and HMM for Surface-Enhanced Raman Spectroscopy Analysis

Hyperbolic metamaterials (HMMs), supporting surface plasmon polaritons (SPPs), and highly confined bulk plasmon polaritons (BPPs) possess promising potential for application as surface-enhanced Raman scattering (SERS) substrates. In the present study, a composite SERS substrate based on a multilayer HMM and gold-nanoparticle (Au-NP) layer was fabricated. A strong electromagnetic field was generated at the nanogaps of the Au NPs under the coupling between localized surface plasmon resonance (LSPR) and a BPP. Additionally, a simulation of the composite structure was assessed using COMSOL; the results complied with those achieved through experiments: the SERS performance was enhanced, while the enhancing rate was downregulated, with the extension of the HMM periods. Furthermore, this structure exhibited high detection performance. During the experiments, rhodamine 6G (R6G) and malachite green (MG) acted as the probe molecules, and the limits of detection of the SERS substrate reached 10⁻¹⁰ and 10⁻⁸ M for R6G and MG, respectively. Moreover, the composite structure demonstrated prominent reproducibility and stability. The mentioned promising results reveal that the composite structure could have extensive applications, such as in biosensors and food safety inspection.

Nanomaterial-Based CO2 Sensors

The detection of carbon dioxide (CO2) is critical for environmental monitoring, chemical safety control, and many industrial applications. The manifold application fields as well as the huge range of CO2 concentration to be measured make CO2 sensing a challenging task. Thus, the ability to reliably and quantitatively detect carbon dioxide requires vastly improved materials and approaches that can work under different environmental conditions. Due to their unique favorable chemical, optical, physical, and electrical properties, nanomaterials are considered state-of-the-art sensing materials. This mini-review documents the advancement of nanomaterial-based CO2 sensors in the last two decades and discusses their strengths, weaknesses, and major applications. The use of nanomaterials for CO2 sensing offers several improvements in terms of selectivity, sensitivity, response time, and detection, demonstrating the advantage of using nanomaterials for developing high-performance CO2 sensors. Anticipated future trends in the area of nanomaterial-based CO2 sensors are also discussed in light of the existing limitations.

Highly sensitive differential fiber-optic SPR sensor in telecom band

We proposed a differential fiber-optic SPR remote sensor with ultra-high sensitivity in telecom band. The working band of the sensor is designed as the C-band which is the low loss band of optical fiber communication aiming to improve the sensitivity and enable the capability of remote monitoring. The sensor head is a BK7 prism coated with Au/TiO₂ films, enabling two channels for differential intensity interrogation. The intensities of the reflected lights through the channels vary oppositely within the measurement range of refractive index. Due to the sharp dip of angular resonant response in the C-band, the differential signal produces a steep slope as the refractive index of the sample varies, thus higher sensitivity is expected in a narrow measurement range. According to the results, the sensitivity is as high as 456 V/RIUs within the narrow measurement range of 1.3×10^-2 RIUs and the resolution reaches to 6×10^-6 RIUs. The measurement range can be tuned conveniently by adjusting the thickness of TiO₂ film and can be expanded by increasing the number of sensing channels, which provides great convenience for the application of biosensor requiring high sensitivity.

Enhancing the sensitivity of plasmonic optical fiber sensors by analyzing the distribution of the optical modes intensity

Improving the sensitivity of plasmonic optical fiber sensors constitutes a major challenge as it could significantly enhance their sensing capabilities for the label-free detection of biomolecular interactions or chemical compounds. While many efforts focus on developing more sensitive structures, we present here how the sensitivity of a sensor can be significantly enhanced by improving the light analysis. Contrary to the common approach where the global intensity of the light coming from the core is averaged, our approach is based on the full analysis of the retro-reflected intensity distribution that evolves with the refractive index of the medium being analyzed. Thanks to this original and simple approach, the refractive index sensitivity of a plasmonic optical fiber sensor used in reflection mode was enhanced by a factor of 25 compared to the standard method. The reported approach opens exciting perspectives for improving the remote detection as well as for developing new sensing strategies.

Bloch Surface Wave Resonance Based Sensors as an Alternative to Surface Plasmon Resonance Sensors

We report on a highly sensitive measurement of the relative humidity (RH) of moist air using both the surface plasmon resonance (SPR) and Bloch surface wave resonance (BSWR). Both resonances are resolved in the Kretschmann configuration when the wavelength interrogation method is utilized. The SPR is revealed for a multilayer plasmonic structure of SF10/Cr/Au, while the BSWR is resolved for a multilayer dielectric structure (MDS) comprising four bilayers of TiO2/SiO2 with a rough termination layer of TiO2. The SPR effect is manifested by a dip in the reflectance of a p-polarized wave, and a shift of the dip with the change in the RH, or equivalently with the change in the refractive index of moist air is revealed, giving a sensitivity in a range of 0.042-0.072 nm/%RH. The BSWR effect is manifested by a dip in the reflectance of the spectral interference of s- and p-polarized waves, which represents an effective approach in resolving the resonance with maximum depth. For the MDS under study, the BSWRs were resolved within two band gaps, and for moist air we obtained sensitivities of 0.021-0.038 nm/%RH and 0.046-0.065 nm/%RH, respectively. We also revealed that the SPR based RH measurement is with the figure of merit (FOM) up to 4.7 × 10-4 %RH-1, while BSWR based measurements have FOMs as high as 3.0 × 10-3 %RH-1 and 1.1 × 10-3 %RH-1, respectively. The obtained spectral interferometry based results demonstrate that the BSWR based sensor employing the available MDS has a similar sensitivity as the SPR based sensor, but outperforms it in the FOM. BSW based sensors employing dielectrics thus represent an effective alternative with a number of advantages, including better mechanical and chemical stability than metal films used in SPR sensing.

Comparison of the Optical Planar Waveguide Sensors’ Characteristics Based on Guided-Mode Resonance

A comparison of optical sensors’ characteristics based on guided-mode resonance has been carried out. It was considered a prism structure with a metal film, a metal grating on a metal substrate and a dielectric grating on a dielectric substrate. It is shown that the main characteristics are determined by the sensitivity of the constant propagation of the respective waveguides on a change in wavelength and a change in the refractive index of the tested medium. In addition, they depend on the full width at half maximum of the spectral or angular reflectance dependence. The corresponding analytical relationships obtained for the three types of sensors are almost the same. It is demonstrated that the ratio of the sensor spectral sensitivity on the resonance curve spectral width is equal to the ratio of the angular sensitivity on the angular width of the corresponding resonance curve for all three types of sensors.

Surface Plasmon Resonance Sensor Based on Dual-Side Polished Microstructured Optical Fiber with Dual-Core

A surface plasmon resonance (SPR) sensor based on a dual-side polished microstructured optical fiber (MOF) with a dual core is proposed for a large analyte refractive index (RI; n_a) detection range. Gold is used as a plasmonic material coated on the polished surface, and analytes can be directly contacted with the gold film. The special structure not only facilitates the fabrication of the sensor, but also can work in the n_a range of 1.42–1.46 when the background material RI is 1.45, which is beyond the reach of other traditional MOF-SPR sensors. The sensing performance of the sensor was investigated by the wavelength and amplitude interrogation methods. The detailed numerical results showed that the proposed sensor can work effectively in the n_a range of 1.35–1.47 and exhibits higher sensitivity in the n_a range of 1.42–1.43.

High-resolution interrogation of tilted fiber Bragg gratings using an extended range dual wavelength differential detection

An extended range dual wavelength differential detection technique for interrogating fiber Bragg grating sensors is implemented for the measurement of tilted fiber Bragg gratings. The dynamic chirp of a single DFB laser diode modulated with a square wave is used to generate two pairs of wavelengths, in the high and low modulation states, with a separation approximately equal to the bandwidth of the TFBG, resulting in a doubling of the range of the DWDD measurement. A spectral resolution of 0.08 pm and a refractive index resolution of 9.9 × 10^-6 are obtained over a range of refractive index of 3.7 × 10^-2, corresponding to 11.9 bits of resolution.

Functionalized Microstructured Optical Fibers: Materials, Methods, Applications

Microstructured optical fiber-based sensors (MOF) have been widely developed finding numerous applications in various fields of photonics, biotechnology, and medicine. High sensitivity to the refractive index variation, arising from the strong interaction between a guided mode and an analyte in the test, makes MOF-based sensors ideal candidates for chemical and biochemical analysis of solutions with small volume and low concentration. Here, we review the modern techniques used for the modification of the fiber's structure, which leads to an enhanced detection sensitivity, as well as the surface functionalization processes used for selective adsorption of target molecules. Novel functionalized MOF-based devices possessing these unique properties, emphasize the potential applications for fiber optics in the field of modern biophotonics, such as remote sensing, thermography, refractometric measurements of biological liquids, detection of cancer proteins, and concentration analysis. In this work, we discuss the approaches used for the functionalization of MOFs, with a focus on potential applications of the produced structures.

A Large Detection-Range Plasmonic Sensor Based on An H-Shaped Photonic Crystal Fiber

An H-shaped photonic crystal fiber (PCF)-based surface plasmon resonance (SPR) sensor is proposed for detecting large refractive index (RI) range which can either be higher or lower than the RI of the fiber material used. The grooves of the H-shaped PCF as the sensing channels are coated with gold film and then brought into direct contact with the analyte, which not only reduces the complexity of the fabrication but also provides reusable capacity compared with other designs. The sensing performance of the proposed sensor is investigated by using the finite element method. Numerical results show that the sensor can work normally in the large analyte RI (n_a) range from 1.33 to 1.49, and reach the maximum sensitivity of 25,900 nm/RIU (RI units) at the n_a range 1.47–1.48. Moreover, the sensor shows good stability in the tolerances of ±10% of the gold-film thickness.

Multiplexed Remote SPR Detection of Biological Interactions through Optical Fiber Bundles

The development of sensitive methods for in situ detection of biomarkers is a real challenge to bring medical diagnosis a step forward. The proof-of-concept of a remote multiplexed biomolecular interaction detection through a plasmonic optical fiber bundle is demonstrated here. The strategy relies on a fiber optic biosensor designed from a 300 µm diameter bundle composed of 6000 individual optical fibers. When appropriately etched and metallized, each optical fiber exhibits specific plasmonic properties. The surface plasmon resonance phenomenon occurring at the surface of each fiber enables to measure biomolecular interactions, through the changes of the retro-reflected light intensity due to light/plasmon coupling variations. The functionalization of the microstructured bundle by multiple protein probes was performed using new polymeric 3D-printed microcantilevers. Such soft cantilevers allow for immobilizing the probes in micro spots, without damaging the optical microstructures nor the gold layer. We show here the potential of this device to perform the multiplexed detection of two different antibodies with limits of detection down to a few tenths of nanomoles per liter. This tool, adapted for multiparametric, real-time, and label free monitoring is minimally invasive and could then provide a useful platform for in vivo targeted molecular analysis.

Method for Determining the Plasmon Resonance Wavelength in Fiber Sensors Based on Tilted Fiber Bragg Gratings

Surface plasmon resonance-based fiber-optic sensors are of increasing interest in modern sensory research, especially for chemical and biomedical applications. Special attention deserves to be given to sensors based on tilted fiber Bragg gratings, due to their unique spectral properties and potentially high sensitivity and resolution. However, the principal task is to determine the plasmon resonance wavelength based on the spectral characteristics of the sensor and, most importantly, to measure changes in environmental parameters with high resolution, while the existing indirect methods are only useable in a narrow spectral range. In this paper, we present a new approach to solving this problem, based on the original method of determining the plasmon resonance spectral position in the automatic mode by precisely calculating the constriction location on the transmission spectrum of the sensor. We also present an experimental comparison of various data processing methods in both a narrow and a wide range of the refractive indexes. Application of our method resulted in achieving a resolution of up to 3 × 10⁻⁶ in terms of the refractive index.

Palladium-coated plasmonic optical fiber gratings for hydrogen detection

Surface plasmon resonance excitation with tilted fiber Bragg gratings has been typically studied using gold films to target biochemical sensing applications. However, surface plasmons can be excited on other metal coatings as well. In this work, plasmonic optical fiber grating platforms are developed using palladium films. Since the optical properties of this metal differ from the ones of gold, simulations are carried out to define the optimal thickness. Due to the phase transition of palladium in the presence of hydrogen, intensity changes in the optical transmission of the devices are produced. It is demonstrated that these platforms can be used for hydrogen detection at concentrations way below the lower explosive limit.

Fiber optic surface plasmon resonance sensor based on a silver-coated large-core suspended-core fiber

A fiber optic surface plasmon resonance (SPR) sensor based on a silver-coated large-core suspended-core fiber was proposed. A dynamic chemical liquid phase deposition method was adopted to fabricate a set of proposed sensors with different silver layer thicknesses. A stable fully spiced all-fiber sensing system was established to evaluate the performance of the fabricated sensors. The results show that the proposed sensor with a thicker silver layer exhibits higher sensitivity and figure of merit. The performance of the proposed sensor is comparable to those of the conventional solid-core fiber and hollow fiber SPR sensors and much higher than that of the metal nanoparticle functionalized suspended-core fiber sensors.

Evaluation of Nanoplasmonic Optical Fiber Sensors Based on D-Type and Suspended Core Fibers with Metallic Nanowires

The introduction of metallic nanostructures in optical fibers has revolutionized the field of plasmonic sensors since they produce sharper and fine-tuned resonances resulting in higher sensitivities and resolutions. This article evaluates the performance of three different plasmonic optical fiber sensors based on D-type and suspended core fibers with metallic nanowires. It addresses how their different materials, geometry of the components, and their relative position can influence the coupling between the localized plasmonic modes and the guided optical mode. It also evaluates how that affects the spatial distributions of optical power of the different modes and consequently their overlap and coupling, which ultimately impacts the sensor performance. In this work, we use numerical simulations based on finite element methods to validate the importance of tailoring the features of the guided optical mode to promote an enhanced coupling with the localized modes. The results in terms of sensitivity and resolution demonstrate the advantages of using suspended core fibers with metallic nanowires.

A Temperature Plasmonic Sensor Based on a Side Opening Hollow Fiber Filled with High Refractive Index Sensing Medium

A surface plasmon resonance temperature sensor based on a side opening hollow-core microstructured optical fiber is proposed in this paper. This design employs a gold nanowire to excite the plasmon mode, and can be easily filled with the sensing medium through the side opening of the fiber, which not only simplifies the fabrication of the sensor but can also use the high refractive index sensing medium. The coupling characteristics, sensing performance and fabrication tolerance of the sensor are analyzed by using the finite element method. The simulation results indicate that the maximum sensitivity is 3.21 nm/°C for the x-polarized core mode in the temperature range of 13.27–50.99 °C, and 4.98 nm/°C for the y-polarized core mode in the temperature range of 14.55–51.19 °C, when benzene is used as the sensing medium. The sensor also shows a good stability in the range of ±10% fabrication tolerance.

Graphene-Enhanced Surface Plasmon Resonance Liquid Refractive Index Sensor Based on Photonic Crystal Fiber

A surface plasmon resonance (SPR) liquid refractive index sensor based on photonic crystal fiber (PCF) is proposed. The PCF is made of the exposed core structure, and the gold film is formed by electron beam evaporation within its defects. The sensitivity of the sensor is improved by coating graphene on the surface of the gold film. The experimental results show that the sensitivity of the sensor is increased by 390 nm/RIU after the introduction of graphene, and finally to 2290 nm/RIU. The experiment and simulation have a good consistency. Significantly, the sensor can be reused, and the measurement accuracy can be maintained.

Optical Planar Waveguide Sensor with Integrated Digitally-Printed Light Coupling-in and Readout Elements

Optical planar waveguide sensors, able to detect and process information from the environment in a fast, cost-effective, and remote fashion, are of great interest currently in different application areas including security, metrology, automotive, aerospace, consumer electronics, energy, environment, or health. Integration of networks of these systems together with other optical elements, such as light sources, readout, or detection systems, in a planar waveguide geometry is greatly demanded towards more compact, portable, and versatile sensing platforms. Herein, we report an optical temperature sensor with a planar waveguide architecture integrating inkjet-printed luminescent light coupling-in and readout elements with matched emission and excitation. The first luminescent element, when illuminated with light in its absorption band, emits light that is partially coupled into the propagation modes of the planar waveguide. Remote excitation of this element can be performed without the need for special alignment of the light source. A thermoresponsive liquid crystal-based film regulates the amount of light coupled out from the planar waveguide at the sensing location. The second luminescent element partly absorbs the waveguided light that reaches its location and emits at longer wavelengths, serving as a temperature readout element through luminescence intensity measurements. Overall, the ability of inkjet technology to digitally print luminescent elements demonstrates great potential for the integration and miniaturization of light coupling-in and readout elements in optical planar waveguide sensing platforms.