Capillary Sensor with Disposable Optrode for Diesel Fuel Quality Testing

Automotive Diesel Fuel Internal Stability Testing with the Use of UV and Temperature as Degradation Factors

Diesel fuel stability can be considered from many points of view, of which the two considered most important are stability in contact with the environment and internal stability. Fuel stability in touch with the environment is often defined as oxidation stability, of which measurement procedures are well developed. The presented paper shows that fuel's internal stability can also be important. The internal stability of diesel fuel with the local use of thermal and ultraviolet radiation (UV) as degradation factors and fluorescence signals as a probe is presented in this paper. We show that the internal degradation of fuel with temperature use differs from that with UV and simultaneous both factors use. Our study shows that using temperature as a degradation factor introduces significant fluorescence fading. Moreover, the fluorescence signal restores significantly later than the sample stabilizes at room temperature. The novelty proposed based on examination is hybrid degradation and an examination cycle that enables the simultaneous use of degradation factors and fluorescence reading. For this purpose, a dedicated measurement setup of signal control and processing was constructed and programmed. The measurement procedure of the data series for specific wavelength enables calculation of signal shifts that allow the internal stability classification of diesel fuel samples in less than 30 min with the cost of a single disposable capillary probe and one polymer plug. Premium and regular fuel examination results show that internal fuel stability can be related to polycyclic aromatic hydrocarbons (PAH) concentrations and can be modified with dedicated additives.

Transient 2D Junction Temperature Distribution Measurement by Short Pulse Driving and Gated Integration with Ordinary CCD Camera

The time resolution of the transient process is usually limited by the minimum exposure time of the high-speed camera. In this work, we proposed a method that can achieve nanosecond temporal resolution with an ordinary CCD camera by driving the LED under test with a periodic short-pulse signal and multiple-cycle superposition to obtain two-dimensional transient junction temperature distribution of the heating process. The temporal resolution is determined by the pulse width of the drive source. In the cooling process, the Boxcar gated integration principle is adopted to complete the two-dimensional transient junction temperature distribution with temporal resolution subject to the minimum exposure time of the CCD camera, i.e., 1 μs in this case. To demonstrate the validity of this method, we measured the two-dimensional transient junction temperature distribution of the blue LEDs according to the principle of thermoreflectance and compared it with the thermal imaging method.

Applications Characteristics of Different Biodiesel Blends in Modern Vehicles Engines: A Review

Two main aspects of the transportation industry are pollution to the environment and depletion of fossil fuels. In the transportation industry, the pollution to the environment can be reduced with the use of cleaner fuel, such as gas-to-liquid fuel, to reduce the exhaust emissions from engines. However, the depletion of fossil fuels is still significant. Biodiesel is a non-toxic, renewable, and biodegradable fuel that is considered an alternative resource to conventional diesel fuel. Even though biodiesel shows advantages as a renewable source, there are still minor drawbacks while operating in diesel engines. Modern vehicle engines are designed to be powered by conventional diesel fuel or gasoline fuel. In this review, the performance, emissions, combustion, and endurance characteristics of different types of diesel engines with various conditions are assessed with biodiesel and blended fuel as well as the effect of biodiesel on the diesel engines. The results show that biodiesel and blended fuel had fewer emissions of CO, HC, and PM but higher NOx emissions than the diesel-fuelled engine. In the endurance test, biodiesel and blended fuel showed less wear and carbon deposits. A high concentration of wear debris was found inside the lubricating oil while the engine operated with biodiesel and blends. The performance, emissions, and combustion characteristics of biodiesel and its blends showed that it can be used in a diesel engine. However, further research on long-term endurance tests is required to obtain a better understanding of endurance characteristics about engine wear of the diesel engine using biodiesel and its blends.

Application of Wireless Accelerometer Mounted on Wheel Rim for Parked Car Monitoring

Damages of different kinds that can be inflicted to a parked car. Among them, loosening of the car wheel bolts is difficult to detect during normal use of the car and is at the same time very dangerous to the health and life of the driver. Moreover, in patents and publications, only little information is presented about electronic sensors available for activation from inside of the car to inform the driver about the mentioned dangerous situation. Thus, the main aim of this work is the proposition and examination of a sensing device using of a wireless accelerometer head to detect loosening of wheel fixing bolts before ride has been started. The proposed sensing device consists of a wireless accelerometer head, an assembly interface and a receiver unit. The assembly interface between the head and the inner part of the rim enables the correct operation of the system. The data processing algorithm developed for the receiver unit enables the proper detection of the unscrewing of bolts. Moreover, the tested algorithm is resistant to the interference signals generated in the accelerometer head by cars and men passing in close distance.

Implementation of Common Rail Direct Injection System and Optimization of Fuel Injector Parameters in an Experimental Single-Cylinder Diesel Engine

The diesel engine is one of the solutions to slow down fossil fuel depletion due to its high efficiency. However, its high pollutant emission limits its usage in many fields. To improve its efficiency and emissions, a conventional mechanical fuel injection system (MFI) was be replaced with common rail direct injection (CRDI) system for the purpose of this study. In this way, injection parameters such as injection timing, injection pressure and multiple injection schemes can be tuned to enhance the engine performance. The rail pressure and engine speed response of the modified diesel engine was tested. It was found that by advancing the start of injection timing (SOI) timing or increasing the rail pressure, the brake torque generated can be increased. Multiple injection schemes can be implemented to reduce the peak heat release rate (HRR). Post injection was observed to increase the late combustion HRR. The maximum pressure rise rate (PRR) can be reduced by applying pilot injection. Further research was conducted on optimizing fuel injector parameters to improve the indicated mean effective pressure (IMEP) consistency and reduce injector power consumption. The consistency of IMEP was indicated by coefficient of variation (CoV) of IMEP. The injector parameters included open time, low time and duty cycle of injector signals. These parameters were optimized by carrying out response surface methodology. The optimized parameters were observed to be 230 µs for open time, 53µs for low time and 27.5% for duty cycle. The percentage of error of CoV of IMEP and injector power were found to be lower than 5% when the predicted results are compared with experimental results.

Modeling In-Vehicle VOCs Distribution from Cabin Interior Surfaces under Solar Radiation

In-vehicle air pollution has become a public health priority worldwide, especially for volatile organic compounds (VOCs) emitted from the vehicle interiors. Although existing literature shows VOCs emission is temperature-dependent, the impact of solar radiation on VOCs distribution in enclosed cabin space is not well understood. Here we made an early effort to investigate the VOCs levels in vehicle microenvironments using numerical modeling. We evaluated the model performance using a number of turbulence and radiation model combinations to predict heat transfer coupled with natural convection, heat conduction and radiation with a laboratory airship. The Shear–Stress Transport (SST) k-ω model, Surface-to-surface (S2S) model and solar load model were employed to investigate the thermal environment of a closed automobile cabin under solar radiation in the summer. A VOCs emission model was employed to simulate the spatial distribution of VOCs. Our finding shows that solar radiation plays a critical role in determining the temperature distribution in the cabin, which can increase by 30 °C for directly exposed cabin surfaces and 10 °C for shaded ones, respectively. Ignoring the thermal radiation reduced the accuracy of temperature and airflow prediction. Due to the strong temperature dependence, the hotter interiors such as the dashboard and rear board released more VOCs per unit time and area. A VOC plume rose from the interior sources as a result of the thermal buoyancy flow. A total of 19 mg of VOCs was released from the interiors within two simulated hours from 10:00 am to noon. The findings, such as modeled spatial distributions of VOCs, provide a key reference to automakers, who are paying increasing attention to cabin environment and the health of drivers and passengers.

Environment-Friendly Biodiesel/Diesel Blends for Improving the Exhaust Emission and Engine Performance to Reduce the Pollutants Emitted from Transportation Fleets

Biodiesel derived from biomass is a renewable source of fuel, and global application of biodiesel in the transport sector has rapidly expanded over the last decade. However, effort has been made to overcome its main shortcoming, i.e., efficiency and exhaust emission characteristics (NOx emissions) in unmodified diesel engines. Biodiesel combustion generally results in lower unburned hydrocarbons (HC), carbon monoxide (CO), and particulate matter (PM) in exhaust emissions compared to fossil diesel. In this study, various biodiesel blends (Chlorella vulgaris, Jatropha curcus, and Calophyllum inophyllum) were investigated for fuel characteristics, and engine performance with exhaust emission compared to diesel. Chlorella vulgaris, Jatropha curcus, and Calophyllum inophyllum biodiesel were synthesized by the acid-base transesterification approach in a microwave reactor and blended with conventional diesel fuel by volume. The fuel blends were denoted as MB10 (90% diesel + 10% microalgae biodiesel), MB20 (80% diesel + 20% microalgae biodiesel), JB10 (90% diesel + 10% jatropha biodiesel), JB20 (80% diesel + 20% jatropha biodiesel), PB10 (90% diesel + 10% polanga biodiesel) and PB20 (80% diesel + 20% polanga biodiesel). Experiments were performed using these fuel blends with a single-cylinder four-stroke diesel engine at different loads. It was shown in the results that, at rated load, thermal efficiency of the engine decreased from 34.6% with diesel to 34.1%, 33.7%, 34.1%, 34.0%, 33.9%, and 33.5% with MB10, MB20, JB10, JB20, PB10, and PB20 fuels, respectively. Unburned hydrocarbon, carbon monoxide and smoke emissions improved with third-generation fuels (MB10, MB20) in comparison to base diesel fuel and second-generation fuels (JB10, JB20, PB10 and PB20). Oxides of nitrogen emissions were slightly increased with both the third- and second-generation fuels as compared to the base diesel. The combustion behavior of microalgae biodiesel was also very close to diesel fuels. In the context of comparable engine performance, emissions, and combustion characteristics, along with biofuel production yield (per year per acre), microalgae biodiesel could have a great potential as a next-generation sustainable fuel in compression engine (CI) engines compared to jatropha and polanga biodiesel fuels.