Separable MSE-Based Design of Two-Way Multiple-Relay Cooperative MIMO 5G Networks

Design and Synchronization Procedures of a D&F Co-Operative 5G Network Based on SDR Hardware Interface: Performance Analysis

Software defined radio (SDR) is a commonly used platform for its ease of operation and cost-effectiveness for the development and testing of real wireless communication systems. By supporting high transmission rates and enabling fast and cost-effective deployments, mainly in millimeter-wave (mmWave), the co-operative 5G network has been standardized by 3GPP Release 16. In this paper, a decode-and-forward (D&F) co-operative hardware network is proposed as one of the key technologies for future 5G/6G wireless networks. The proposed system consists of an emulated base station processing unit (gnodeB), a D&F protocol and the user equipment (UE). In particular, the design of the D&F relay node is based on an MIMO layer 2 relay technology. A testbed based on an SDR platform and MatlabTM software, in which the physical broadcast channel (PBCH) transmission, physical downlink control channel (PDCCH), physical downlink shared channel (PDSCH), and downlink shared channel (DL-SCH) for transport channel coding, according to the 3GPP standardized 5G downlink signal, has been designed. The key performance indicators (KPIs), namely EVM, BER, and throughput, were measured for 5G signals with 64-QAM and 256-QAM modulation schemes. The obtained results show that the D&F co-operative 5G network achieves substantially improved KPIs in the communication between the gnodeB and the UE in an outdoor-to-indoor scenario. Furthermore, it has been demonstrated that the D&F protocol presents a good performance and behavior being compared to one commercial equipment.

Advanced Physical-Layer Technologies for Beyond 5G Wireless Communication Networks

Fifth-generation (5G) networks will not satisfy the requirements of the latency, bandwidth, and traffic density in 2030 and beyond, and next-generation wireless communication networks with revolutionary enabling technologies will be required. Beyond 5G (B5G)/sixth-generation (6G) networks will achieve superior performance by providing advanced functions such as ultralow latency, ultrahigh reliability, global coverage, massive connectivity, and better intelligence and security levels. Important aspects of B5G/6G networks require the modification and exploitation of promising physical-layer technologies. This Special Issue (SI) presents research efforts to identify and discuss the novel techniques, technical challenges, and promising solution methods of physical-layer technologies with a vision of potential involvement in the B5G/6G era. In particular, this SI presents innovations and concepts, including nonorthogonal multiple access, massive multiple-input multiple-output (MIMO), energy harvesting, hybrid satellite terrestrial relays, Internet of Things-based home automation, millimeter-wave bands, device-to-device communication, and artificial-intelligence or machine-learning techniques. Further, this SI covers the proposed solutions, including MIMO antenna design, modulation detection, interference management, hybrid precoding, and statistical beamforming along with their performance improvements in terms of performance metrics, including bit error rate, outage probability, ergodic sum rate, spectrum efficiency, and energy efficiency.

A Two-Hop mmWave MIMO NR-Relay Nodes to Enhance the Average System Throughput and BER in Outdoor-to-Indoor Environments

Millimeter-Wave (mmWave) bands are receiving enormous attention in 5G mobile communications, due to the capability to provide a multi-gigabit transmission rate. In this paper, a two-hop architecture for 5G communications with the capacity to support high end-to-end performance due to the use of Relay Nodes (RNs) in mmWave-bands is presented. One of the novelties of the paper is the implementation of Amplify-and-Forward (A&F) and Decode-and-Forward (D&F) RNs along with a mmWave-band transceiver chain (Tx/Rx). In addition, two approaches for channel estimation were implemented at the D&F RN for decoding the backhaul link. One of them assumes complete knowledge of the channel (PCE), and the other one performs the channel estimation through Least Square (LS) estimator. A large number of simulations, using MATLABTM and SimulinkTM software, were performed to verify the potential benefits of the proposal two-hop 5G architecture in an outdoor-to-indoor scenario. The main novelty in performing these simulations is the use of signals with 5G features, as DL-SCH transport channel coding, PDSCH generation, and SS Burst generation, which is another of the main contributions of the paper. On the other hand, mmWave transmitter and receiver chains were designed and implemented with off-the shelf components. The simulations show that the two-hop network substantially improves the Key Performance Indicators (KPIs), Bit Error Rate (BER), and Throughput, in the communications between the logical 5G Radio Node (gNodeB), and the New Radio User Equipment (NR-UE). For example, a throughput improvement of 22 Mbps is obtained when a 4 × 4 × 2 MIMO D&F with LS architecture is used versus a SISO D&F with PCE architecture for Signal-to-Noise Ratio (SNR) = 20 dB and 64-QAM signal. This improvement reaches 96 Mbps if a 256-QAM signal is considered. The improvement in BER is 11 dB and 10.5 dB, respectively, for both cases. This work also shows that the obtained results with D&F RNs are better than with A&F RNs. For example, an improvement of 17 Mbps in the use of SISO D&F with LS vs. SISO A&F, for the 64-QAM signal is obtained. Besides, this paper constitutes a first step to the implementation of a mmWave MIMO 5G cooperative network platform.